Sharp AR-150 (serv.man9) Service Manual ▷ View online
6. Communication section
Note: These items are factory adjusted when shipping according to
FCC standards. Therefore, do not change the setting in the
market.
market.
A. Dial test (<FAX mode> SIM 66-13)
(1) Dial pulse transmission test
1) Execute SIM 66-13 in FAX mode.
2) Execute the dial pulse mode according to the instructions on the
2) Execute the dial pulse mode according to the instructions on the
LCD display.
SELECT SIGNAL
1:PULSE 2:DTMF
3) Set the make time.
INPUT MAKE TIME
(0–15)
Default: 0123456789#
(After deleting with the clear key, it can be set to any desired
value.)
(After deleting with the clear key, it can be set to any desired
value.)
5) Transmission is started from the line.
SEND yyPPS xxm s
1:YES 2:NO
SENDING yyPPS xxm s
SIM
Soft SW
Initial
value
value
Set value
Dial
pulse
make
time
pulse
make
time
10
PPS
PPS
FAX
mode
66-13
mode
66-13
SW67-
1 – 4
1 – 4
40ms
(14)
(14)
SW set value:
0 – 15
Make time:
25 – 41ms
0 – 15
Make time:
25 – 41ms
1ms
step
(Binary
input)
step
(Binary
input)
(2) DTMF signal transmission level adjustment
1) Execute SIM 66-13 in the FAX mode.
2) Execute the DTMF mode according to the instructions on the
2) Execute the DTMF mode according to the instructions on the
LCD display.
SELECT SIGNAL
1:PULSE 2:DTMF
3) Select the signal transmission level.
The signal transmission level is classified into two groups: the
high group, and the low group.
Transmission can be made with either of default and the soft
SW set value.
high group, and the low group.
Transmission can be made with either of default and the soft
SW set value.
SELECT HIGH LEVEL
1:DEFAULT 2:SOFT SW.
SELECT LOW LEVEL
1:DEFAULT 2:SOFT SW.
4) The transmission level can be set when the following menu is
displayed on the LCD. (et value 1 = 0.5dB change)
INPUT VALUE
(0–15)
(This value is returned to the original value when the simulation
mode is canceled.)
mode is canceled.)
Default: 0123456789#
(After deleting with the clear key, it can be set to any desired value.)
(After deleting with the clear key, it can be set to any desired value.)
6) Start transmission from the line.
H:xx L:yy
1:YES 2:NO
SENDING DTMF
xx: High group soft SW set value
yy: Low group soft SW set value
yy: Low group soft SW set value
SIM
Soft SW
Initial
value
value
Set value
DTMF
trans-
mission
level
trans-
mission
level
High
group
group
(FAX
mode)
66-13
(Test
only)
mode)
66-13
(Test
only)
SW53-
1 – 4
1 – 4
3.5dB
(7)
(7)
SW set
value: 0 –
15
Transmis-
sion level: 0
– 7.5db
value: 0 –
15
Transmis-
sion level: 0
– 7.5db
0.5ms
step
(Binary
input)
step
(Binary
input)
Low
group
group
SW53-
5 – 8
5 – 8
3.5dB
(7)
(7)
AR-F151
8 – 12
6. Communication section
Note: These items are factory adjusted when shipping according to
FCC standards. Therefore, do not change the setting in the
market.
market.
A. Dial test (<FAX mode> SIM 66-13)
(1) Dial pulse transmission test
1) Execute SIM 66-13 in FAX mode.
2) Execute the dial pulse mode according to the instructions on the
2) Execute the dial pulse mode according to the instructions on the
LCD display.
SELECT SIGNAL
1:PULSE 2:DTMF
3) Set the make time.
INPUT MAKE TIME
(0–15)
Default: 0123456789#
(After deleting with the clear key, it can be set to any desired
value.)
(After deleting with the clear key, it can be set to any desired
value.)
5) Transmission is started from the line.
SEND yyPPS xxm s
1:YES 2:NO
SENDING yyPPS xxm s
SIM
Soft SW
Initial
value
value
Set value
Dial
pulse
make
time
pulse
make
time
10
PPS
PPS
FAX
mode
66-13
mode
66-13
SW67-
1 – 4
1 – 4
40ms
(14)
(14)
SW set value:
0 – 15
Make time:
25 – 41ms
0 – 15
Make time:
25 – 41ms
1ms
step
(Binary
input)
step
(Binary
input)
(2) DTMF signal transmission level adjustment
1) Execute SIM 66-13 in the FAX mode.
2) Execute the DTMF mode according to the instructions on the
2) Execute the DTMF mode according to the instructions on the
LCD display.
SELECT SIGNAL
1:PULSE 2:DTMF
3) Select the signal transmission level.
The signal transmission level is classified into two groups: the
high group, and the low group.
Transmission can be made with either of default and the soft
SW set value.
high group, and the low group.
Transmission can be made with either of default and the soft
SW set value.
SELECT HIGH LEVEL
1:DEFAULT 2:SOFT SW.
SELECT LOW LEVEL
1:DEFAULT 2:SOFT SW.
4) The transmission level can be set when the following menu is
displayed on the LCD. (et value 1 = 0.5dB change)
INPUT VALUE
(0–15)
(This value is returned to the original value when the simulation
mode is canceled.)
mode is canceled.)
Default: 0123456789#
(After deleting with the clear key, it can be set to any desired value.)
(After deleting with the clear key, it can be set to any desired value.)
6) Start transmission from the line.
H:xx L:yy
1:YES 2:NO
SENDING DTMF
xx: High group soft SW set value
yy: Low group soft SW set value
yy: Low group soft SW set value
SIM
Soft SW
Initial
value
value
Set value
DTMF
trans-
mission
level
trans-
mission
level
High
group
group
(FAX
mode)
66-13
(Test
only)
mode)
66-13
(Test
only)
SW53-
1 – 4
1 – 4
3.5dB
(7)
(7)
SW set
value: 0 –
15
Transmis-
sion level: 0
– 7.5db
value: 0 –
15
Transmis-
sion level: 0
– 7.5db
0.5ms
step
(Binary
input)
step
(Binary
input)
Low
group
group
SW53-
5 – 8
5 – 8
3.5dB
(7)
(7)
AR-F151
8 – 12
6. Communication section
Note: These items are factory adjusted when shipping according to
FCC standards. Therefore, do not change the setting in the
market.
market.
A. Dial test (<FAX mode> SIM 66-13)
(1) Dial pulse transmission test
1) Execute SIM 66-13 in FAX mode.
2) Execute the dial pulse mode according to the instructions on the
2) Execute the dial pulse mode according to the instructions on the
LCD display.
SELECT SIGNAL
1:PULSE 2:DTMF
3) Set the make time.
INPUT MAKE TIME
(0–15)
Default: 0123456789#
(After deleting with the clear key, it can be set to any desired
value.)
(After deleting with the clear key, it can be set to any desired
value.)
5) Transmission is started from the line.
SEND yyPPS xxm s
1:YES 2:NO
SENDING yyPPS xxm s
SIM
Soft SW
Initial
value
value
Set value
Dial
pulse
make
time
pulse
make
time
10
PPS
PPS
FAX
mode
66-13
mode
66-13
SW67-
1 – 4
1 – 4
40ms
(14)
(14)
SW set value:
0 – 15
Make time:
25 – 41ms
0 – 15
Make time:
25 – 41ms
1ms
step
(Binary
input)
step
(Binary
input)
(2) DTMF signal transmission level adjustment
1) Execute SIM 66-13 in the FAX mode.
2) Execute the DTMF mode according to the instructions on the
2) Execute the DTMF mode according to the instructions on the
LCD display.
SELECT SIGNAL
1:PULSE 2:DTMF
3) Select the signal transmission level.
The signal transmission level is classified into two groups: the
high group, and the low group.
Transmission can be made with either of default and the soft
SW set value.
high group, and the low group.
Transmission can be made with either of default and the soft
SW set value.
SELECT HIGH LEVEL
1:DEFAULT 2:SOFT SW.
SELECT LOW LEVEL
1:DEFAULT 2:SOFT SW.
4) The transmission level can be set when the following menu is
displayed on the LCD. (et value 1 = 0.5dB change)
INPUT VALUE
(0–15)
(This value is returned to the original value when the simulation
mode is canceled.)
mode is canceled.)
Default: 0123456789#
(After deleting with the clear key, it can be set to any desired value.)
(After deleting with the clear key, it can be set to any desired value.)
6) Start transmission from the line.
H:xx L:yy
1:YES 2:NO
SENDING DTMF
xx: High group soft SW set value
yy: Low group soft SW set value
yy: Low group soft SW set value
SIM
Soft SW
Initial
value
value
Set value
DTMF
trans-
mission
level
trans-
mission
level
High
group
group
(FAX
mode)
66-13
(Test
only)
mode)
66-13
(Test
only)
SW53-
1 – 4
1 – 4
3.5dB
(7)
(7)
SW set
value: 0 –
15
Transmis-
sion level: 0
– 7.5db
value: 0 –
15
Transmis-
sion level: 0
– 7.5db
0.5ms
step
(Binary
input)
step
(Binary
input)
Low
group
group
SW53-
5 – 8
5 – 8
3.5dB
(7)
(7)
AR-F151
8 – 12
6. Communication section
Note: These items are factory adjusted when shipping according to
FCC standards. Therefore, do not change the setting in the
market.
market.
A. Dial test (<FAX mode> SIM 66-13)
(1) Dial pulse transmission test
1) Execute SIM 66-13 in FAX mode.
2) Execute the dial pulse mode according to the instructions on the
2) Execute the dial pulse mode according to the instructions on the
LCD display.
SELECT SIGNAL
1:PULSE 2:DTMF
3) Set the make time.
INPUT MAKE TIME
(0–15)
Default: 0123456789#
(After deleting with the clear key, it can be set to any desired
value.)
(After deleting with the clear key, it can be set to any desired
value.)
5) Transmission is started from the line.
SEND yyPPS xxm s
1:YES 2:NO
SENDING yyPPS xxm s
SIM
Soft SW
Initial
value
value
Set value
Dial
pulse
make
time
pulse
make
time
10
PPS
PPS
FAX
mode
66-13
mode
66-13
SW67-
1 – 4
1 – 4
40ms
(14)
(14)
SW set value:
0 – 15
Make time:
25 – 41ms
0 – 15
Make time:
25 – 41ms
1ms
step
(Binary
input)
step
(Binary
input)
(2) DTMF signal transmission level adjustment
1) Execute SIM 66-13 in the FAX mode.
2) Execute the DTMF mode according to the instructions on the
2) Execute the DTMF mode according to the instructions on the
LCD display.
SELECT SIGNAL
1:PULSE 2:DTMF
3) Select the signal transmission level.
The signal transmission level is classified into two groups: the
high group, and the low group.
Transmission can be made with either of default and the soft
SW set value.
high group, and the low group.
Transmission can be made with either of default and the soft
SW set value.
SELECT HIGH LEVEL
1:DEFAULT 2:SOFT SW.
SELECT LOW LEVEL
1:DEFAULT 2:SOFT SW.
4) The transmission level can be set when the following menu is
displayed on the LCD. (et value 1 = 0.5dB change)
INPUT VALUE
(0–15)
(This value is returned to the original value when the simulation
mode is canceled.)
mode is canceled.)
Default: 0123456789#
(After deleting with the clear key, it can be set to any desired value.)
(After deleting with the clear key, it can be set to any desired value.)
6) Start transmission from the line.
H:xx L:yy
1:YES 2:NO
SENDING DTMF
xx: High group soft SW set value
yy: Low group soft SW set value
yy: Low group soft SW set value
SIM
Soft SW
Initial
value
value
Set value
DTMF
trans-
mission
level
trans-
mission
level
High
group
group
(FAX
mode)
66-13
(Test
only)
mode)
66-13
(Test
only)
SW53-
1 – 4
1 – 4
3.5dB
(7)
(7)
SW set
value: 0 –
15
Transmis-
sion level: 0
– 7.5db
value: 0 –
15
Transmis-
sion level: 0
– 7.5db
0.5ms
step
(Binary
input)
step
(Binary
input)
Low
group
group
SW53-
5 – 8
5 – 8
3.5dB
(7)
(7)
AR-F151
8 – 12