Sharp AL-840 (serv.man8) Service Manual ▷ View online
S004/Ua001/Ub002/P001/CLN
S004/Ua001/Ub002/P002/CLN
S004/Ua001/Ub001/
P001/CLN
P001/CLN
S004/Ua001/Ub001/
P003/CLN
P003/CLN
S004/Ua001/Ub001/
P002/CLN
P002/CLN
S004/Ua001/P001
S004/Ua001/
P004/GRE
P004/GRE
S004/Ua001
S004/Ua001/P008
S004/Ua001/
P002
P002
S004/Ua001/
P006/GRE
P006/GRE
S004/Ua001/
P007/GRE
P007/GRE
S004/Ua001/
P006/GRE
P006/GRE
S004/Ua001/
P005/CLN
P005/CLN
S004/Ua001/P008
S004/Ua001/P008
9 – 13
S004/Ua001
Scanner unit
(1)
Remove the rear cabinet S001/P001 .
(2)
Remove the front upper cabinet S001/P002 .
(3)
Remove the right cabinet S001/P003 .
(4)
Remove the left cabinet S001/P004 .
(5)
Remove the document table glass S001/P007 .
(6)
Remove the fan motor unit S010/P001 .
(7)
Remove the screw, the connector, and the hook, and remove
the scanner unit (S004/Ua001).
the scanner unit (S004/Ua001).
S004/Ua001/P001
Scanner home positions sensor
S004/Ua001/P002
Scanner (copy) lamp drive PWB
S004/Ua001/P003
Scanner motor
S004/Ua001/P004
Scanner motor gear
S004/Ua001/P005
CCD unit
S004/Ua001/P006
Scanner rail
S004/Ua001/P007
Scanner shaft
S004/Ua001/P008
Scanner drive wire
(1)
Remove the rear cabinet S001/P001 .
(2)
Remove the front upper cabinet S001/P002 .
(3)
Remove the right cabinet S001/P003 .
(4)
Remove the left cabinet S001/P004 .
(5)
Remove the document table glass S001/P007 .
(6)
Remove the fan motor unit S010/P001 .
(7)
Remove the screw and remove the scanner shaft.
(8)
Release the hook, cut the binding band, and remove the scan-
ner home position sensor (S004/Ua001/P001).
ner home position sensor (S004/Ua001/P001).
*
Troubles caused by improper work
1) L1-00 trouble
2) L3-00 trouble
(9)
Remove the screw and remove the dark box cover.
(10) Remove the screw and the connector, and remove the scanner
lamp drive PWB. (S004/Ua001/P002).
S004/Ua001
S004/Ua001/P001
S004/Ua001/P002
9 – 14
(11) Remove the screw, the spring, and the belt, and remove the
scanner motor unit.
(12) Remove the screw and remove the scanner motor (S004/
Ua001/P003).
(13) Remove the E-ring, and remove the scanner motor gear (S004/
Ua001/P004).
*
Grease
Apply grease to #1 position.
*
Troubles caused by improper work
1) L1-00 trouble
2) L3-00 trouble
3) Image deflection
(14) Remove the screw and the connector, and remove the CCD unit
(S004/Ua001/P005).
(Never remove the other screws than the two screws shown
below.)
(Never remove the other screws than the two screws shown
below.)
*
Cleaning
Remove the protection cover, and clean the CCD and the lens
with absolute alcohol.
with absolute alcohol.
*
Troubles caused by improper work
1) E7-04 trouble
2) E7-05 trouble
3) E7-12 trouble
4) Copy image defect
(Improper focusing)
(Distortion)
(Streaks in the sub scanning direction)
(Distortion)
(Streaks in the sub scanning direction)
S004/Ua001/P003
S004/Ua001/P003
1
S004/Ua001/P004/GRE
S004/Ua001/P005
9 – 15
(15) Remove the screw, and remove the scanner shaft (S004/Ua001/
P007).
*
Grease
Apply grease to the scanner rail (S004/Ua001/P006).
*
Troubles caused by improper work
1) Copy image defect
(Image deflection)
(16) Remove the scanner drive wire (S004/Ua001/P008).
*
Assembly procedure
1) Hang the scanner drive wire fixing metal on the scanner unit
hook.
2) Pass the wire through the outside grove of the double pulley of
the scanner unit B.
3) Hold the winding pulley groove upside, wind the wire 11 turns.
Insert the 9th turn of wire into the winding pulley groove and fix
it with the screw.
it with the screw.
4) Wind the wire over the pulley through under the scanner unit
B.
5) Pass the wire through the inside groove of the double pulley of
the scanner unit B.
6) Hang the spring hook on the scanner unit.
*
Note for assembly
The wire on the front frame side is different from that on the rear
frame side. Be careful not to mistake the wire colors.
frame side. Be careful not to mistake the wire colors.
*
Troubles caused by improper work
1) L1-00 trouble
2) L3-00 trouble
3) Copy image defect
(Distortion)
(Image deflection)
(Image deflection)
S004/Ua001/Ub001
Scanner unit A
S004/Ua001/Ub001/P001
Scanner lamp
S004/Ua001/Ub001/P002
No. 1 mirror
S004/Ua001/Ub001/P003
Scanner lamp light
quantity sensor
quantity sensor
(1)
Remove the rear cabinet S001/P001 .
(2)
Remove the front upper cabinet S001/P002 .
(3)
Remove the right cabinet S001/P003 .
(4)
Remove the left cabinet S001/P004 .
(5)
Remove the document table glass S001/P007 .
(6)
Remove the fan motor unit. S010/P001 .
(7)
Remove the lamp cover, lift the scanner lamp diagonally, and
remove the scanner lamp (S004/Ua001/Ub001/P001).
remove the scanner lamp (S004/Ua001/Ub001/P001).
*
Cleaning
Use absolute alcohol to clean the scanner lamp.
*
Troubles caused by improper work
1) Copy image defect
(Streaks in the sub scanning direction)
(Uneven density)
(Uneven density)
S004/Ua001/
P006/GRE
P006/GRE
S004/Ua001/
P007/GRE
P007/GRE
S004/Ua001/
P006/GRE
P006/GRE
P008
S004/Ub001/P001/CLN
9 – 16
Click on the first or last page to see other AL-840 (serv.man8) service manuals if exist.