DOWNLOAD Sharp AL-1217 (serv.man17) Service Manual ↓ Size: 5.15 MB | Pages: 118 in PDF or view online for FREE

AL-1226  OPERATIONAL DESCRIPTIONS  7 - 6

1) Before paper feed operation, the manual paper feed solenoid

(MPFS) is turned OFF as shown in the figure below.

2) When the PRINT button is pressed, the manual paper feed

solenoid (MPFS) turns on to disengage the manual paper feed
latch.
A from the manual paper feed clutch sleeve A, rotating the manual
paper feed roller and the manual take-up roller. At the same time,
the manual paper feed stopper opens and the manual take-up
roller is pressed to the surface of the paper to start paper feeding.

3) When pawl C of the manual paper feed clutch sleeve is engaged

with the manual feed latch, the manual feed stopper falls and the
manual take-up roller rises. At that time, the manual paper feed
roller is rotating.

4) The lead edge of the transported paper is pressed on the resist

roller by the transport roller. Then the paper is stopped temporarily
to allow synchronization with the lead edge of the image on the
OPC drum.
From this point, the operation is the same as the paper feed
operation from the tray. (Refer to A-5 - 8.)

5) The solenoid turns off to close the gate and return to the initial

state.

OF

MPFS

F

C

A

ON

MPFS

A

C

ON

MPFS

A

C

OF

MPFS

F

A

C

AL-1226  OPERATIONAL DESCRIPTIONS  7 - 7

1) When the power is turned on, the detection gear 38T is rotated in

the arrow direction by the detection gear 20T to push the micro-
switch (process detection switch) installed to the machine sensor
cover, making a judgement as a new drum.

2) When the detection gear 38T turns one rotation, there is no gear

any more and it stops.
The latch section of the 38T gear is latched and fixed with the
projection of the process cover.

The SPF (Single Path Feeder) is installed to the AL-1225 as a stan-
dard provision, and it automatically copies up to 30 sheets of docu-
ments of a same size. (Only one set of copies)

a

PPD1 jam

PPD1 does not turn off within 4 sec after turning 
on the resist roller.

b

PPD2 jam

PPD2 is off immediately after turning on the 
resist roller.

PPD2 does not turn off within 1.2 sec after 
turning off the resist roller.

c

POD jam 

POD does not turn on within 2.9 sec after turning 
on the resist roller.

POD does not turn off within 1.5 sec - 2.7 sec 
after turning off PPD2.

Gear 20T

Process detection switch

Gear 38T

1

Pickup roller

2

Sheet of document for 
paper feed

3

Set detection ACT

4

Paper stopper

5

Document feed roller

6

Separation sheet

7

Paper entry sensor

8

PS roller D

9

Transport follower roller

10

Paper exit roller

11

Paper exit follower roller

12

Document tray

Gear notch

Gear pawl

Projection

Gear notch

Gear pawl

Projection

2

1

3

4

5

6

7

8

9

10

11

12

AL-1226  OPERATIONAL DESCRIPTIONS  7 - 8

1) When SPPD is ON (document remaining) when the power is

turned on.

2) When SPPD is not turned ON within about 1.5 sec (at 100% copy)

after starting the document feed operation.

3) When SPPD is not turned on within about 4.7 sec (at 100% copy)

after turning on SPPD.

4) When the SPF document jam release door or the OC cover is

opened during document transport (SPF motor rotating).

SPID ON

PSW ON

MIRM rotation

MM rotation

CPFS ON

SPFM rotation

SPUS ON

Document set

Document set sensor

Document feed unit lamp ON

PPD ON

RRC ON

SPPD ON

POD ON

Copy start

The scanner is shifted
to the exposure position.

(Copier side)

Main motor rotation

Paper feed

Synchronization

(Transfer)

(Fusing)

(Document exit)

Paper transport

(Exposure)

In the zooming mode, the magnification ratio in the sub 
scanning direction (paper transport direction) is adjusted
by changing the document transport speed.

(Paper exit)

SPF motor rotation

Document feed

Document transport sensor

Document transport

(SPF side)

Time chart (Tray feed)

752msec

625msec

756msec

PSW

MIRR M

SPF M

CL

SPUS
SPPD

SCANST

MAIN M

CPFS1

RRS
PPD1

PPD2

POD

AL-1226  DISASSEMBLY AND ASSEMBLY  8 - 1

The disassembly and assembly procedures are described for the fol-
lowing sections:

1.

High voltage section

2.

Operation panel section

3.

Optical section

4.

Fusing section

5.

Tray paper feed/transport section

6.

Manual paper feed section

7.

Rear frame section

8.

Power section

9.

SPF section

1) Press the side cover open/close button and open the side cover.

2) Push up the lock pawls (2 positions) of the side cover, and remove

the transfer charger.

For assembly, reverse the disassembly procedure.

1) Remove the charger cleaner from the manual paper feed unit.

No.

Part name Ref.

1

Transfer charger unit

2

Charger wire

Transfer
charger

Lock pawl rear

Lock pawl front

1)