Sharp PN-R903 Handy Guide ▷ View online
Precautions for direct sunlight
Please set this monitor to avoid the direct sunlight. These conditions may cause failure and/or deterioration.
The effect of direct sunlight
The effect of the heat
-The effect of the heat
(Even though the environmental temperature is fairly low, the temperature of the area under direct sunlight could be high.)
Monitor will break down or uniformity issue will occur.
-The effect of ultraviolet rays
-The effect of ultraviolet rays
LCD or color filter will deteriorate.
Countermeasure
-Set a sun-shade to protect the display from ultraviolet and infrared rays
-Set a sun-shade to protect the display from ultraviolet and infrared rays.
PN-R903 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
4
Precautions for dust
Precautions for using anti-dust display
About dust
-Fundamentally, LCD monitor is designed for indoor usage.
When it is being used outdoor or at dusty places such as
-when using the anti-dust display(enclosure), please remove
the
d t ith filt
d t ith filt
-When it is being used outdoor, or at dusty places, such as
railway station or close to the traffic, the solutions against dust
must be considered.
railway station or close to the traffic, the solutions against dust
must be considered.
Precautions for using the filter
(1)it is possible to prolong the filter life by
using two filter and exchanging the fine
using two filter and exchanging the fine
dust with filter.
-If the anti-dust solutions are not being considered ->
The dust will enter into the LCD panel through the gaps and will
The effect of dust
(2)it may raise the internal temperature for a display when using the
filter, because of raising the air resistance.
Please reduce the air resistance by increasing the area of filter, etc.
filter, because of raising the air resistance.
Please reduce the air resistance by increasing the area of filter, etc.
g
g g
screen pre-filter.
The dust will enter into the LCD panel through the gaps and will
cause the distorted image (see example below), and will break
down in the end.
cause the distorted image (see example below), and will break
down in the end.
(3)when making the enclosure, it needs the caution whether the fan
air-breathe or exhaust the air.
air-breathe or exhaust the air.
Intake air fan:
The pressure in the enclosure is higher than out of enclosure
The pressure in the enclosure is higher than out of enclosure.
Therefore, dust does not break in the housing. It is limited the size of
intake vent. And it is difficult to suck in much air(when using in dusty
area).
Therefore, dust does not break in the housing. It is limited the size of
intake vent. And it is difficult to suck in much air(when using in dusty
area).
Exhaust air fan:
The dust enters into the LCD panel
and causes the distorted image.
AS
Countermeasure against dust
C
t
l t l
l d
l
The pressure in the housing is lower than out of enclosure.
Therefore, dust breaks in the housing. It has much size of intake
vent. And it is easy to control the temperature(when using in less
dusty area and severe temperature requirements).
Therefore, dust breaks in the housing. It has much size of intake
vent. And it is easy to control the temperature(when using in less
dusty area and severe temperature requirements).
-Create a completely sealed enclosure.
-The completely sealed enclosure shut off dust so it is
advantageous for installation in locations with excessive
amounts of dust, outdoor, and that may occur in salt.
advantageous for installation in locations with excessive
amounts of dust, outdoor, and that may occur in salt.
※
to keep the performance, please clean the filter regularly
PN-R903 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
5
-You will need to be a combination of countermeasure against
thermal, such as the heat exchanger and the air conditioner.
thermal, such as the heat exchanger and the air conditioner.
Intake air fan
Exhaust air fan
Precautions for reflection, dew condensation and water drops
-when attaching LCD panel to protection panel, the reflection
occurs and the visibility comes down.
occurs and the visibility comes down.
About reflection
About dew condensation, water drops
-Humidity condition for IDP
Range of humidity condition for IDP : From 20% to 80%(no
y
-Regarding protecting the reflection non-glare, it is effective to
use the non-glare protection panel.
use the non-glare protection panel.
-Non glare coating has two methods. First method is AR coating
which decreases the reflection rate with light Second method is
which decreases the reflection rate with light Second method is
Range of humidity condition for IDP : From 20% to 80%(no
condensation)
-Dew condensation and/or liquid drops will cause the
breakdown of the circuit and/or LCD panel.
Please install LCD away from condensation and liquid drops
breakdown of the circuit and/or LCD panel.
Please install LCD away from condensation and liquid drops
which decreases the reflection rate with light. Second method is
silica coating which decreases the reflection rate with scattered
reflected light.
-Silica coating is cheaper than AR coating. However, images
easily defocus and view angle is narrow with Silica coating.
silica coating which decreases the reflection rate with scattered
reflected light.
-Silica coating is cheaper than AR coating. However, images
easily defocus and view angle is narrow with Silica coating.
Please install LCD away from condensation and liquid drops.
-the environment which has high possibility of condensation
The place where temperature is generally low but has
frequent warm air flow.
(Example : the place in front of the vents of radiators When
The place where temperature is generally low but has
frequent warm air flow.
(Example : the place in front of the vents of radiators When
Please check it before installation.
-Generally, when decreasing the reflection rate, image quality
comes down. Therefore, please select the suitable protection
panel in each installing location.
comes down. Therefore, please select the suitable protection
panel in each installing location.
(Example : the place in front of the vents of radiators. When
the radiator is turn on in a cold winter morning, condensation
occurs.)
the radiator is turn on in a cold winter morning, condensation
occurs.)
-the environment which has high possibility of water drops
“Semi-outdoor” place where strong winded-rain(typhoon)
“Semi-outdoor” place where strong winded-rain(typhoon)
-the closer a distance from the protection panel to the LCD panel
get the clear image. Indeed, LCD surface temperature raise.
get the clear image. Indeed, LCD surface temperature raise.
(Please keep 3 cm clearance to flow the air.)
Semi-outdoor place where strong winded-rain(typhoon)
could potentially reach the monitor. The place which is below
the pipes inside the ceiling. (When installing in these places,
countermeasures should be taken to avoid water drops to
reach the monitors. For example, covering the LCD monitor
with box. In such a case, consideration should be given for
direction of vent.)
the pipes inside the ceiling. (When installing in these places,
countermeasures should be taken to avoid water drops to
reach the monitors. For example, covering the LCD monitor
with box. In such a case, consideration should be given for
direction of vent.)
Exhausting the
air to back
air to back
PN-R903 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
6
AR coating
Air-breathing
from below
from below
Precautions for vibration, inclination, voltage, residual images and expansion
-This information display is not designed for the usage in any
places which have strong vibrations, such as inside motor
places which have strong vibrations, such as inside motor
About vibration
-When a still image is being displayed for a long period, image
retention might occur.
retention might occur.
About residual images
p
g
vehicles.
-If the monitors will be used in the place which has the possibility
of even small vibration like railway station’s platform, shock
absorber must be considered.
of even small vibration like railway station’s platform, shock
absorber must be considered.
g
-Image retention can be removed by displaying motion images
or turning off the monitor. However, the longer the still image is
being displayed, the harder to remove the image retention,
therefore, the solutions mentioned above should be taken
or turning off the monitor. However, the longer the still image is
being displayed, the harder to remove the image retention,
therefore, the solutions mentioned above should be taken
About orientation
periodically.
About orientation
-Installing with inclination more than 20 degrees is impossible.
Ab
t
i
About expansion
-When using acrylic or polycarbonate protection panel, please be
aware of expansion due to heat or moisture absorption.
aware of expansion due to heat or moisture absorption.
About power supply and voltage
Please use certainly the attached or designated power cord
Acrylic protection panel can expand about 0.4%(about 8 mm)
when absorbing the moisture.
when absorbing the moisture.
Please fix the protection panel not to strain it by expansion.
-Please use certainly the attached or designated power cord.
Attached power cord is three pin for 100V level. For
200V(50/60Hz) level, provided service parts(QACCJA104WJPZ)
(with change)
Attached power cord is three pin for 100V level. For
200V(50/60Hz) level, provided service parts(QACCJA104WJPZ)
(with change)
PN-R903 Installation Guidelines <Rev1.0> February 2013
CONFIDENTIAL
7
Click on the first or last page to see other PN-R903 service manuals if exist.