Sharp PN-L802B (serv.man2) Handy Guide ▷ View online
PN-L802B Installation Guidelines <Rev1.0> February 2012
CONFIDENTIAL
Precautions in installing and moving
Precautions in installing and handling 1
The display surface is made of glass.
Please use rear handgrip and underside of
the display while installing and moving.
Please do not hold surface, sensor side,
the edge and power button of the display.
It is possible to cause damage and
malfunction of display. Please be careful
not to drop the display.
Please use rear handgrip and underside of
the display while installing and moving.
Please do not hold surface, sensor side,
the edge and power button of the display.
It is possible to cause damage and
malfunction of display. Please be careful
not to drop the display.
Caution for Installing
Prior to installing the PN-L802B, please refer to following items carefully in order to use PN-L802B for long term reliable service.
- The accompanying stand is for temporary use until the display installed formally. It is not for permanent use and please do not turn on power of the
monitor when the temporary stand is used.
- Please fasten a USB cable with cable clamp to the cabinet.
- Please use a mounting bracket which can support 4 times weight of the display. The wall on which displays are mounted must support 4 times total
weight of the display and mounting bracket (etc. concrete wall / concrete pillar).
- Only vertical installation perpendicular to level surface is recommended, and the limitation of the inclination angle is between 0 to 20 degrees upward.
- Usable temperature range of this display is 5℃-35℃. Using in other condition may cause failure and deterioration.
Please keep enough space to avoid heating.
- Please set this display keeping out of direct sunlight. It may cause failure and deterioration.
- It is necessary to take measures against dust such as regular cleaning in a dusty area.
- For safety, please give measures for preventing fall of display.
- The ground connection is necessary when the power plug is connected.
- Please fasten a USB cable with cable clamp to the cabinet.
- Please use a mounting bracket which can support 4 times weight of the display. The wall on which displays are mounted must support 4 times total
weight of the display and mounting bracket (etc. concrete wall / concrete pillar).
- Only vertical installation perpendicular to level surface is recommended, and the limitation of the inclination angle is between 0 to 20 degrees upward.
- Usable temperature range of this display is 5℃-35℃. Using in other condition may cause failure and deterioration.
Please keep enough space to avoid heating.
- Please set this display keeping out of direct sunlight. It may cause failure and deterioration.
- It is necessary to take measures against dust such as regular cleaning in a dusty area.
- For safety, please give measures for preventing fall of display.
- The ground connection is necessary when the power plug is connected.
Please ask the professional dealer/contractor if you can’t keep the ground connection.
-
Please refer to the “SAFETY PRECAUTIONS”, “TIPS AND SAFETY INSTRUCTION” and “MOUNTING
PRECAUTIONS” which is described in the operation manual of the display as well.
- Please
be careful that the warranty can’t be applied if these precautions are not kept.
4
×
<Caution>
The holding positions are changed from
PN-L702B/L602B.
Please be careful to hold the edge of the
PN-L702B/L602B display, and do not hold
lower part of the bezel.
The holding positions are changed from
PN-L702B/L602B.
Please be careful to hold the edge of the
PN-L702B/L602B display, and do not hold
lower part of the bezel.
PN-L802B Installation Guidelines <Rev1.0> February 2012
CONFIDENTIAL
5
Precautions in installing and handling 2
Worker position, assignment of work and cautions at lifting up the display.
Please wear gloves and safety shoes when you lift up this display.
For lifting up the display 6 people is required. (Ex. Moving display from the package to wheeled platform.)
Following the image below, please check the position and assignment for each worker, and lift up the display to set the stand.
※Please refer to P9 andP10 if you set this display to the stand (PN-ZS80F) which is recommended by SHARP.
You can’t complete installation by these steps below.
×
WorkerA;
hold handle1 with left hand.
hold handle3 with right hand.
hold handle1 with left hand.
hold handle3 with right hand.
WorkerB;
hold handle2 with left hand.
hold the underside of the main body
with right hand.
*Please do not hold the corner of the
display.
hold handle2 with left hand.
hold the underside of the main body
with right hand.
*Please do not hold the corner of the
display.
WorkerC;
hold the underside of the
main body with both hands.
hold the underside of the
main body with both hands.
WorkerD;
hold the underside of the main
body with both hands.
hold the underside of the main
body with both hands.
*please be careful not to touch the
power button.
power button.
WorkerE;
hold handle5 with right hand.
hold the underside of the main
body with left hand.
*please do not hold the corner
of the display and the power
button.
hold handle5 with right hand.
hold the underside of the main
body with left hand.
*please do not hold the corner
of the display and the power
button.
WorkerF;
hold handle4 with right hand.
hold handle6 with left hand.
hold handle4 with right hand.
hold handle6 with left hand.
1
2
4
5
3
6
PN-L802B Installation Guidelines <Rev1.0> February 2012
CONFIDENTIAL
6
Precautions for orientation
About orientation
- Only vertical installation perpendicular to level surface is recommended.
-The limitation of the inclination angle is between 0 to 20 degrees upward. Even within 20 degrees
range, please consult individually when installing with inclination.
range, please consult individually when installing with inclination.
Only vertical installation is recommended.
Within 20 degrees
More than 20
degrees
Installing with inclination is impossible.
Even within 20 degrees range,
please consult individually when
installing with inclination.
please consult individually when
installing with inclination.
○
×
PN-L802B Installation Guidelines <Rev1.0> February 2012
CONFIDENTIAL
7
Precautions on stand installation
(SHARP stand)
1
Precautions on stand installation
Please read the user instruction carefully and carry out installation with the stand we SHARP recommend. (PN-ZS80F)
Please refer to the detailed installation manual for stand assembling. (Supplementary material)
After stand installation, please lock casters to prevent its unexpected move.
After installation, please lock front casters forward,
and rear casters backward.
and rear casters backward.
Keep a caster locked
Height after stand installation
About the height of each display after stand installation, please refer to the following list. (Unit : mm)
Display TOP
Display BOTTOM
80”
(with PN-ZS80F)
70”
(with PN-ZS701)
60”
(with PN-ZS609)
80”
(with PN-ZS80F)
70”
(with PN-ZS701)
60”
(with PN-ZS609)
Highest position
2,100
1,800
1,800
943
818
915
Lowest position
1,800
1,500
1,500
643
518
615
Keep a caster locked
Keep a caster locked
Click on the first or last page to see other PN-L802B (serv.man2) service manuals if exist.