Sharp PN-L703A (serv.man3) Service Manual ▷ View online
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES 4- 27
13. USAGE TIME SETTING PROCEDURE
13-1. OPERATING CONDITIONS OF THE USAGE
TIME SETTING TOOL
The operating conditions of the Gamma setting read tool of the
information display are as follows.
OS
(32bit Only)
- Windows 8
- Windows Vista
- Windows 7
Communication
port
- LAN(100 BASE-TX / 10BASE-TX)
■ When connected to the information display
with a LAN cable
Refer to the followings of [7. INSTRUCTIONS FOR LAUNCHER
TOOL] to connect the information display and the PC.
■ Connected to the information display with a LAN cable
■ How to prepare the network settings
■ How to set PC automatically with using DHCP
■ How to set PC manually without using DHCP
■ How to set Information Display with using DHCP
■ How to set Information Display without using DHCP
■ How to confirm the connection of PC and Information display
13-2. START-UP OF THE USAGE TIME SETTING
TOOL
Press [Usage Time] button of the Service Tool Launcher.
13-3. USAGE TIME SETTING PROCEDURES
The procedures of setting usage time with use of the Usage Time
Setting Tool are as follows.
1) Press [Connection Setting...] button to configure the
communication settings.
2) Input the usage time you need to set in the field of Write Data.
It should be from “000000” to “200000.” Make sure to input a
6-digit number.
3) Press [Write] button.
4) Press [Read] button, and confirm that the set usage time is
displayed in the Read Data field.
13-4. USAGE TIME CHECK PROCEDURE
With an image displayed on the display, use the accessory remote
controller to enter the SERVICE MENU 1, and check the USAGE
TIME on the column of USAGE TIME.
To enter the SERVICE MENU 1, press and hold [SIZE] button on
the remote controller for 5 sec, and press the buttons in the
sequence of [VOL + ()], [VOL - ()], [BRIGHT - ( )],[BRIGHT +
()].
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES 4- 28
14. MODEL NAME SETTING PROCEDURES
14-1. OPERATING CONDITIONS OF THE MODEL
NAME SETTING TOOL
The operating conditions of the Gamma setting read tool of the
information display are as follows.
OS
(32bit Only)
- Windows 8
- Windows Vista
- Windows 7
Communication
port
- LAN(100 BASE-TX / 10BASE-TX)
■ When connected to the information display
with a LAN cable
Refer to the followings of [7. INSTRUCTIONS FOR LAUNCHER
TOOL] to connect the information display and the PC.
■ Connected to the information display with a LAN cable
■ How to prepare the network settings
■ How to set PC automatically with using DHCP
■ How to set PC manually without using DHCP
■ How to set Information Display with using DHCP
■ How to set Information Display without using DHCP
■ How to confirm the connection of PC and Information display
14-2. START-UP OF THE MODEL NAME SETTING
TOOL
Press [Model Name] button of the Service Tool Launcher.
14-3. MODEL NAME SETTING PROCEDURES
The procedures of setting model names with use of the Model
Name Setting Tool are as follows.
1 ) Input the model name in the field of Write Data.
Normally, the model name has been already input at the time
of start-up. Therefore you don’t need to change it.
2 ) Press [Connection Setting...] button to configure the
communication settings.
3 ) Press [Write] button.
4 ) Press [Read] button, and confirm that the model name is
displayed in the Read Data field.
* When the model name is changed, turn OFF and ON before
saving the log and setting to the USB flash drive, restoring the
settings from USB flash drive or updating the firmware.
Until turning OFF and On the main power, this function access to
the previous model name folder.
14-4. MODEL NAME CHECK METHOD
Press [Display] button on the remote controller to indicate the
display information, and check the model name.
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES 4- 29
15. WHITE BOARD SCREEN ADJUSTMENT PROCEDURE
In the monitor with the internal controller, the video image is input as the analog RGB signal internally. It is necessary to adjust the
settings to the proper values on sampling because the characteristic of the analog RGB signal defers from each device.
When the Main I/F PWB or the internal controller is replaced, perform this adjustment.
15-1. OPERATING CONDITIONS OF WHITE
BOARD INPUT SCREEN TOOL
The operating conditions of the Gamma setting read tool of the
information display are as follows.
OS
(32bit Only)
- Windows 8
- Windows Vista
- Windows 7
Communication
port
- LAN(100 BASE-TX / 10BASE-TX)
■ When connected to the information display
with a LAN cable
Refer to the followings of [7. INSTRUCTIONS FOR LAUNCHER
TOOL] to connect the information display and the PC.
■ Connected to the information display with a LAN cable
■ How to prepare the network settings
■ How to set PC automatically with using DHCP
■ How to set PC manually without using DHCP
■ How to set Information Display with using DHCP
■ How to set Information Display without using DHCP
■ How to confirm the connection of PC and Information display
15-2. ADJUSTMENT PROCEDURE
1) Start up the monitor and change the input setting to the
whiteboard.
2) Display the screen adjustment pattern on the whiteboard.
- When the whiteboard is in the [Normal mode],
1. Touch the [Setting] on the launcher.
2. Input the administrator password.
3. Select the [Admin-Settings] tab.
4. Touch the [Start Screen Adjust Tool] on the [Touch Panel
Settings].
- When the whiteboard is in the [Service mode],
Touch the [Adj_uty] icon on the desktop.
3) Start up the Screen Adjust Tool.
Touch the [W/B Screen Adjustment] button on the launcher.
4) Perform the screen adjustment automatically.
Touch the [RUN] button.
The [K] mark is displayed on the left top of the screen and the
adjustment is done automatically.
5) When the [Success] is displayed, the adjustment is finished.
When the edges of screen adjustment pattern are blurred or
the pattern is not vivid, perform the step 4) again.
When the pattern is not still displayed correctly even if the step
is performed again, set each setting from the [Touch Panel
Tool Property].
6) Touch the screen adjustment pattern and finish the
adjustment .
<CAUTION>
- When the [K] mark is still displayed on the left top of the screen
after the adjustment is finished, the adjustment is failed. In this
case, confirm the connection of the monitor and perform the step
4) again.
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES 4- 30
16. OPERATING MANUAL OF THE LOG TOOL
In the monitor, the user setting and system information are saved as the log information. There are two kinds of the procedures to get
the log.
- Log display tool
Refer to the “LOG DISPLAY TOOL OPERATION PROCEDURE”.
- USB flash drive
Refer to the “SAVE LOG TO THE USB FALSH DRIVE”
16-1. PREPARE
・
PC with Windows XP/Vista/7 OS and LAN configuration
・
LAN cable (Cross cable when connecting directly to the
information display, or straight cable when connecting via a
hub)
・
Information display provided with the LAN function and the log
output function Connect the PC and the information display
with the LAN cable. If they are directly connected, setting
must be made both in the PC and in the information display.
When connecting a PC to the network in order to obtain log
information from the information display which is already
connected to the network, consult the network administrator on
the PC setting.
16-2. BOOTING
Press [InfoDisp Report] button of the Service Tool Launcher.
Select the model for obtaining the log, and press [OK].
16-3. GET AND DISPLAY LOGS
1 ) When a model is selected, the following window is displayed.
The actual display slightly differs depending on the selected
model.
Depending on the models which are not supported are lightly
displayed.
Confirm that the [LAN] is selected on the [Interface] and click
[LAN setting] button.
The following window is displayed. Input the IP address and
data port (The default setting of the data port is 10008) of the
monitor. When the user name and the password are set, input
them. These settings are not saved. Therefore, once this tool is
closed, these settings needs to be set again.
2 ) After completion of the setting of “1)” press [Get Logs] button.
Click on the first or last page to see other PN-L703A (serv.man3) service manuals if exist.