Sharp PN-L703A (serv.man3) Service Manual ▷ View online
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES 4- 35
17. SAVE LOG TO THE USB FLASH DRIVE
17-1. USB FALSH DRIVE
It is necessary to prepare the USB flash drive which supports the
following standard.
- Format : FAT32/FAT16(The upper limit of the cluster size is
32KB)
- USB 2.0/1.1
<CAUTION>
- The card reader for the SD card is not supported
- Set the proper name to the volume label
- USB hub is not supported.
- Do not use the encrypted USB flash drive.
- Turn OFF and ON the main power right after the model name is
changed.
17-2. SAVE THE LOG
1) Press the [ENTER] from the [SAVE LOG] of [SERVICE
MENU3]. The following message is displayed.
2) Connect the USB flash drive to the monitor.
The connector of the USB flash drive is coved.
3) Select the [YES] and press the [ENTER]. The setting is
saved.
4) When the saving operation is finished, the operation moves
back to the Service Menu.
The initial file name is “XXlog_[Model name]_[Serial number]
[Date(YYYYMMDD)]_[Data type].dat”. This is saved in the
[Model Name] folder in the USB flash drive.
5) When the saving operation is failed, the following message is
displayed. Connect the USB flash drive again or turn OFF and
ON the monitor and save the log again.
Failed to save file
6) When the saving operation is failed repeatedly, change the
USB flash drive.
17-3. ERROR MESSAGE
- Could not save. Drive has no free memory
There is no space to save the log file in the USB flash drive.
- USB not recognized. Check the connection.
The monitor cannot recognize the USB flash drive.
- Failed to save file
The name of the saving file is overlapped with the one in the
USB flash drive.
It is not possible to write the log lie to the USB flash drive.
Other date writing operation error is occurred.
.
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES 4- 36
18. USER SETTING TOOL OPERATION PROCEDURES
This tool allows saving the setting contents of the machine into a PC.
If the user’s request on the setting is known in advance, make the requested setting by using a machine of the same model in the sales
depot before installing the product in the user’s site, and save the setting to a PC. After installation, transfer the setting in the PC to the
user’s PC. (There are some setting contents which cannot be saved.)
<CAUTION>
- The saved user setting values can be used with the same model of the monitor.
- The operation of the monitor cannot be guaranteed when the saved user setting values are written to the different model of the monitor.
There are two kinds of the procedures to save or set the user setting values.
- Use the service tool
Refer to the “USER SETTING TOOL OPERATION PROCEDURE”.
- Use the USB flash drive
Refer to the “SAVE OR RESTORE THE USER SETTING VALUES TO THE USB FALSH DRIVE”.
18-1. OPERATING CONDITIONS OF THE USER
SETTING VALUE TOOL
The operating conditions of the Gamma setting read tool of the
information display are as follows.
OS
(32bit Only)
- Windows 8
- Windows Vista
- Windows 7
Communication
port
- LAN LAN(100 BASE-TX / 10BASE-TX)
■ When connected to the information display
with a LAN cable
Refer to the followings of [7. INSTRUCTIONS FOR LAUNCHER
TOOL] to connect the information display and the PC.
■ Connected to the information display with a LAN cable
■ How to prepare the network settings
■ How to set PC automatically with using DHCP
■ How to set PC manually without using DHCP
■ How to set Information Display with using DHCP
■ How to set Information Display without using DHCP
■ How to confirm the connection of PC and Information display
18-2. BOOTING THE USER SETTING VALUE
TOOL
Press [User Setting value] button of the service tool launcher.
18-3. USER SETTING VALUE BACKUP
PROCEDURES
1 ) Press [Connection Setting] button to make connection setting.
2 ) Turn ON the information display.
3 ) Select the range of set values to be backed up.
All
All user setting values
Picture Only
User setting values related to pictures only
4 ) Press [Read] button.
5 ) The dialog for saving the file is displayed. The initial file name
is “XXprop_ [Model name]_[Serial number]
[Date(YYYYMMDD)]_[Data type].bak”.
Check the file name and press [Save] button to save the user
setting values.
<CAUTION>
When you used the saved data for the restoration of the machine,
do not change the file name.
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES 4- 37
18-4. USER SETTING VALUE RESTORING
PROCEDURES
1) Press [Connection Setting] button to make connection setting.
2) Turn ON the information display.
3) Press [Write ...] button, and select the saved backup file.
4) After completion of restoring, the information display is reset.
<CAUTION>
-
When the massage of “This Monitor is not Support. Is restore
processing continued?”, “Backup data is not for this monitor. Is
restore processing continued?”, “Serial Number is different
between monitor and backup data. Is restore processing
continued?”, or “Model Name is different between monitor and
backup data. Is restore processing continued?” is displayed, the
backup of the target set may be failed. Check again, and
perform restoring.
-
Some setting contents cannot be saved by this tool.
WHEN “TIME OUT. CANNOT CONNECT. PLEASE
CONFIRM SETTING.” IS DISPLAYED:
-
Check the power status of the information displayed which is
connected.
-
Check to confirm that the PC and the information display are
properly connected with an RS-232C cable.
WHEN “CANNOT OPEN INTERFACE. CANNOT
CONNECT. PLEASE CONFIRM SETTING” IS
DISPLAYED:
-
Check to confirm that the port which is set by another tool
is not used. If the port is used by another tool, turn OFF
the
tool.
WHEN “THIS MONITOR IS NOT SUPPORT. IS XXXX
PROCESSING CONTINUED?” IS DISPLAYED:
-
The display which is connected is not supported by this tool. Use
a tool which supports the displayed connected.
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
SERVICE MENU/VARIOUS SETTING TOOL OPERATING PROCEDURES 4- 38
19.SAVE OR RESTORE THE USER SETTING VALUES TO THE USB FALSH DRIVE
19-1. USB FALSH DRIVE
It is necessary to prepare the USB flash drive which supports the
following standard.
- Format : FAT32/FAT16(The upper limit of the cluster size is
32KB)
- USB 2.0/1.1
<CAUTION>
- The card reader for the SD card is not supported
- Set the proper name to the volume label
- USB hub is not supported.
- Do not use the encrypted USB flash drive.
- Turn OFF and ON the main power right after the model name is
changed.
19-2. SAVE THE USER SETTING VALUE
1) Press the [ENTER] from the [SAVE/RESTORE SETTINGS
VALUE] of [SERVICE MENU3]. The following message is
displayed.
2) Select the [SAVE] and press the [ENTER]. Select the items to
save and press the [ENTER].
All
All user setting values
The settings which are not saved:
- IP address of the LAN
- Settings which are changed by the input
signal like clock, phase, etc.
Picture Only
User setting values related to pictures only
3) Connect the USB flash drive.
4) Select the [YES] and press the [ENTER]. The setting is
saved.
5) When the saving operation is finished, the operation move
back to the Service Menu.
The initial file name is “XXlog_[Model name]_[Serial number]
[Date(YYYYMMDD)]_[Setting range information].bak”. This is
saved in the [Model Name] folder in the USB flash drive.
6) When the saving operation is failed, the following message is
displayed. Connect the USB flash drive again or turn OFF
and ON the monitor and save the log again.
Failed to save file
7) When the saving operation is failed repeatedly, change the
USB flash drive.
19-3. RESTORE THE USER SETTING VALUE
1) Select the [RESTORE] and press the [ENTER]. Select the
items to save and press the [ENTER].
2) The files saved in the [Model name] folder in the USB flash
drive are displayed. Select the file to restore and press the
[ENTER].
The restore operation is started. During the operation, do not
disconnect the USB flash drive.
].
3) When the operation is finished, the monitor is turned OFF and
ON.
19-4. ERROR MESSAGE
- Could not save. Drive has no free memory
There is no space to save the log file in the USB flash drive.
- USB not recognized. Check the connection.
The monitor cannot recognize the USB flash drive.
- Failed to save file
The name of the saving file is overlapped with the one in the
USB flash drive.
It is not possible to write the log lie to the USB flash drive.
Other date writing operation error is occurred.
SAVE/RESTORE SETTINGS VALUES
SAVE =>
RESTORE =>
OK…[ENTER] BACK…[RETURN]
SAVE/RESTORE SETTINGS VALUES
SAVE =>
RESTORE =>
OK…[ENTER] BACK…[RETURN]
RESTORE
A123456789_201205221350A
A123456789_201205221348P
A123456789_201205220150A
OK…[ENTER] BACK…[RETURN]
Click on the first or last page to see other PN-L703A (serv.man3) service manuals if exist.