Sharp PN-L601 (serv.man5) Service Manual ▷ View online
CHAPTER 1. OUTLINE OF THE PRODUCT
PN-L601B OUTLINE OF THE PRODUCT
1 – 13
4. OPTION
4 - 1. PN-ZB01
■ SUPPLIED ACCESSORIES
n
Expansion Board: 1
n
Terminal label: 1
n
Mounting screws: 1
n
Operation manual: 1
n
Speaker cable core: 2
n
Installation Manual (instructions for SHARP dealers and service engineers): 1
■ INSTALLATION PROCEDURE
CAUTION
n
Do not touch the connectors of this product and LCD MONITOR. The static electricity in your body may cause breakdown.
n
Touch a grounded source to discharge the static electricity in your body before starting operation.
n
The illustrations in this manual are for explanatory purposes and may not exactly represent the actual product.
1 ) Set the main power switch of the monitor to “off” and disconnect
the power from the wall outlet.
2 ) Spread a thick and soft cloth (such as a blanket) on a level surface,
such as a table, and place the monitor on it with its LCD panel fac-
ing downward.
3 ) Remove the expansion terminal cover.
Remove 8 screws.
4 ) Remove the dummy plate.
Remove 2 screws.
Give the dummy plate to the customer and ask them to store it.
Always install the dummy plate after removing the expansion
Always install the dummy plate after removing the expansion
board.
5 ) Attach the expansion board.
Fully insert the connector.
6 ) Secure the expansion board.
Secure the board with the supplied mounting screw and the 2
screws removed in Step 4.
screws removed in Step 4.
7 ) Attach the expansion terminal cover.
Secure the cover with the 8 screws removed in Step 3).
8 ) Affix the terminal label in the area indicated by (A) in the above
illustration.
Expansion terminal cover
Dummy plate
Connector
Connector
Supplied screws
(A)
PN-L601B INSTALLATION, ADJUSTMENT, SETTING
2 – 1
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
1. INSTALLATION
CAUTION
INSTALLING PRECAUTIONS
n
This product is for use indoors.
n
Since the monitor is heavy, consult your dealer before installing,
removing or moving the monitor.
n
When installing, removing or moving the monitor, ensure that this
is carried out by at least 2 people.
is carried out by at least 2 people.
n
A mounting bracket compliant with VESA specifications is required.
Do not use any screw holes other than VESA holes for installation.
n
When moving the monitor, be sure to hold it with either both han-
dles or the 4 corners on the bottom of the unit.
Do not place your hand on the screen. This may cause product
damage, failure, or injury.
damage, failure, or injury.
n
Install the monitor with the surface perpendicular to a level sur-
face.
n
Mounting the monitor on the wall requires special expertise and
the work must be performed by an authorized SHARP dealer.
You should never attempt to perform any of this work yourself.
You should never attempt to perform any of this work yourself.
Our company will bear no responsibility for accidents or injuries
caused by improper mounting or mishandling.
n
This monitor should be used at an ambient temperature between
41°F (5°C) and 95°F (35°C). Provide enough space around the
41°F (5°C) and 95°F (35°C). Provide enough space around the
monitor to prevent heat from accumulating inside.
n
If it is difficult to provide this much space for any reason such as
the installation of the monitor inside a housing, or if the ambient
the installation of the monitor inside a housing, or if the ambient
temperature may be outside of the range of 41°F (5°C) and 95°F
(35°C), install a fan or take other measures to keep the ambient
temperature within the required range.
temperature within the required range.
n
Temperature condition may change when using the display
together with the optional equipments recommended by SHARP.
In such cases, please check the temperature condition specified
by the optional equipments.
by the optional equipments.
n
Adhere to the following when installing the monitor in the vertical
orientation. Failing to adhere to the following may cause malfunc-
tions.
tions.
--- Install the monitor such that the power LED is located on the
downside.
--- Set the “MONITOR on the SETUP” menu to “PORTRAIT”.
--- Be sure to clamp the power cord (supplied) onto the fixed part
below using the provided cable clamp. When clamping the
power cord, take care not to stress the terminal of the power
cord. Do not bend the power cord excessively.
n
Do not block any ventilation openings. If the temperature inside
the monitor rises, this could lead to a malfunction.
n
After mounting, it is recommended to take some measures to
prevent the monitor from falling down.
prevent the monitor from falling down.
n
Do not place the monitor on a device which generates heat.
n
Be sure to use a wall-mount bracket designed or designated for
mounting the monitor.
n
This monitor is designed to be installed on a concrete wall/ceiling
or pillar. Reinforced work might be necessary for some materials
such as plaster/thin plastic board/wood before starting installa-
such as plaster/thin plastic board/wood before starting installa-
tion. This monitor and bracket must be installed on a wall which
can endure at least 4 times or more the weight of the monitor.
Install by the most suitable method for the material and the struc-
Install by the most suitable method for the material and the struc-
ture.
n
Do not use the product in locations where the unit is exposed to
direct sunlight or other strong light. Since this product operates
with infrared rays, such light may cause a malfunction.
with infrared rays, such light may cause a malfunction.
Unit: inch [cm]
FOR THE MONITOR IN
HORIZONTAL ORIENTATION
HORIZONTAL ORIENTATION
FOR THE MONITOR IN
VERTICAL ORIENTATION
VERTICAL ORIENTATION
7-7/8 [20]
2 [5]
2
[5]
2
[5]
1-7/16
[3.5]
[3.5]
1-13/16
[4.5]
[4.5]
7-7/8
[20]
[20]
2
[5]
2
[5]
2 [5]
Cable clamp attachment
Cable clamp
Power cord (Supplied)
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
PN-L601B INSTALLATION, ADJUSTMENT, SETTING
2 – 2
n
Use the supplied vertical logo sticker when you install the monitor
in vertical orientation.
*
1
Do not remove the factory-affixed sticker but affix the logo sticker
over it. Be careful not to cover the remote control sensor or but-
tons.
tons.
n
Contact your dealer or a service engineer to have the USB cable
installed or removed.
Risk of electrical shock or injury if you attempt the work yourself.
n
Before connecting the USB cable, turn off the main power switch
and disconnect the power cable from the outlet.
and disconnect the power cable from the outlet.
n
Use only the provided USB cable.
n
Contact your dealer or a service engineer to have the power
switch installed or removed.
switch installed or removed.
Risk of electrical shock or injury if you attempt the work yourself.
1 ) Remove the protective seal and connect the connector.
2 ) Align the mounting brackets with the slot in the bottom of the unit
and tighten the screws (x 2).
Make sure that the mounting brackets are firmly secured.
Make sure that the mounting brackets are firmly secured.
Take care that the cable is not caught or pinched.
3 ) Attach the screw.
*
1
Operation panel
Logo
1
2
2
Bottom
Power switch
Protective
seal
seal
Connector
Mounting
bracket
bracket
Mounting
bracket
bracket
3
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
PN-L601B INSTALLATION, ADJUSTMENT, SETTING
2 – 3
1 - 1. CONNECTING PERIPHERAL EQUIPMENT
CAUTION
n
Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/disconnecting cables. Also, read the
manual of the equipment to be connected.
n
Be careful not to mix up the input terminal with the output terminal when connecting cables. Mixing up the input and output terminals may cause
malfunctions and the other problems.
WHEN THE PN-ZB01 (OPTIONAL) IS ATTACHED
F
G
H
I
J K
M
O
L N
For power
outlet
outlet
4
5
6 7
9
8
3
1
2
When the PN-ZB01 (optional)
is attached
is attached
1 AC input terminal
2 Power cord (Supplied)
3 USB cable
4 PC/AV HDMI input terminal
5 PC D-sub input terminal
6 Audio input terminal
7 Audio output terminals
8 RS-232C output terminal
9 RS-232C input terminal
F PC/AV DVI-D input terminal
G PC/AV DVI-D output terminal
H LAN terminal
I External speaker terminals
J Audio 1 input terminals
K Audio 2 input terminals
L PC RGB input terminals
M AV component input terminals
N AV video input terminal
O AV S-video input terminal
Click on the first or last page to see other PN-L601 (serv.man5) service manuals if exist.