Sharp PN-E702 (serv.man5) User Manual / Operation Manual ▷ View online
17
E
Turning Power On/Off
n
Operation mode
When the monitor is turned on for the first time after being
shipped from the factory, the operation mode setting screen
will be displayed. Set it to MODE1 or MODE2.
MODE1 ....OFF IF NO OPERATION is set to ON, and
STANDBY MODE is set to LOW POWER. (These
settings can not be changed.)
If there is no operation for 4 hours or more, the
monitor automatically enters standby mode. Power
consumption in standby mode is also minimized.
MODE2 ....Will perform standard operation.
OFF IF NO OPERATION is set to OFF, and
STANDBY MODE is set to STANDARD. These
settings can be changed.
Even after being set, changes can be made using
OPERATION MODE, located in the menu of the monitor. (See
page 22.)
n
Date/time setting
• If the time has yet to be set when the monitor is first turned
on, the date/time setting screen appears. Set the date and
time.
DATE/TIME SETTING
SET
CANCEL
/
/
OK···[MENU]
:
:
01
01
11
/
00
00
:
/ 20
1. Press
,
,
or
to select the date and
time, and press
or
to change the numerical
values.
2. Press
or
to select SET and then press
MENU
.
• Be sure to set the date and time.
• The date/time setting screen will close automatically if no
operation is performed for about 15 seconds. The date
and time can be set using DATE/TIME SETTING from
the OPTION menu when the date/time setting screen
disappears.
TIPS
•
Set the date in “Day/Month/Year” order.
•
Set the time on a 24-hour basis.
•
The clock is maintained by the internal battery.
•
If you already set the time but the date/time setting
screen appears when the power is turned on, the
internal battery may be exhausted. Please contact
your local SHARP servicing dealer or service center for
assistance with battery replacement.
•
Estimated service life of the internal battery: About 5
years (depending on monitor operation)
•
The initial battery was inserted at the factory when the
monitor was shipped, so it may run out of power before
its expected operation life.
Disabling power on/off operations
Power on/power off operations can be disabled in order to
protect the monitor from an accidental power off. Set the
ADJUSTMENT LOCK in FUNCTION menu to “ON 2”. (See
page 29.)
18
E
Basic Operation
1
2
3
4
4
5
6
7
8
1. INPUT (Input mode selection)
The menu is displayed. Press
The menu is displayed. Press
or
to select the input
mode, and press
to enter.
* You can select the input terminal by pressing the input
switch of the monitor.
Input mode
Video
Audio
PC D-SUB
PC D-sub input terminal
*1
Audio input terminal
PC HDMI
PC/AV HDMI input terminal
*2
*3
AV HDMI
PC/AV HDMI input terminal
*2
AV COMPONENT PC D-sub input terminal
*1
Audio input terminal
AV VIDEO
PC D-sub input terminal
*1
When the PN-ZB01 (optional) is attached
Input mode
Video
Audio
PC DVI-D
PC/AV DVI-D input terminal
*4
*3
PC HDMI
PC/AV HDMI input terminal
*2
PC D-SUB
PC D-sub input terminal
*1
PC RGB
PC RGB input terminals
*5
AV DVI-D
PC/AV DVI-D input terminal
*4
AV HDMI
PC/AV HDMI input terminal
*2
AV COMPONENT
AV COMPONENT input
terminals
terminals
*5
PC D-sub input terminal
*1
AV S-VIDEO
AV S-video input terminal
AV VIDEO
AV video input terminal
PC D-sub input terminal
PC D-sub input terminal
*1
*1 Select the terminal to be used in D-SUB of INPUT
SELECT. (See page 23.)
*2 Select the terminal to be used in HDMI of INPUT SELECT.
(See page 23.)
*3 Select the terminal for AUDIO SELECT which is used for
audio input. (See page 23.)
*4 Select the terminal to be used in DVI of INPUT SELECT.
(See page 23.)
*5 Select the terminal to be used in BNC of INPUT SELECT.
(See page 23.)
2. MUTE
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the
previous level.
3. MENU
Displays and turns off the menu screen. (see page 20.)
4. VOL +/- (Volume adjustment)
Pressing
Pressing
or
displays the VOLUME menu when the
menu screen is not displayed.
V O L U M E
15
Press
or
to adjust the volume of the sound.
* If you do not press any buttons for about 4 seconds, the
VOLUME menu automatically disappears.
5. BRIGHT +/- (Backlight adjustment)
Pressing
or
displays the BRIGHT menu when the
menu screen is not displayed.
B R I G H T
15
Press
or
to adjust the brightness.
* If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
6. SIZE (Screen size selection)
The menu is displayed.
Press
Press
or
to select the screen size. (See page 19.)
7. DISPLAY
Displays monitor information. When you press this button
again, the display disappears.
When the PN-ZB01 (optional) is attached, the display changes
from INFORMATION1 → INFORMATION2 → clear display,
and so on every time you press this button.
• The display disappears automatically after about 15
seconds.
•
LAN
is displayed during LAN communication.
• If
LAN
is displayed in red, there is a duplicate IP address.
8. MODE (Color mode selection)
Each time you press this button, the color mode changes in
the following order:
STD (Standard) → VIVID → sRGB →
HIGH ILLUMINANCE → STD...
• HIGH ILLUMINANCE is a display with colors suited to
bright locations.
• sRGB applies to PC input only.
sRGB is international standard of color representation
specified by IEC (International Electrotechnical
Commission). Color conversion is made in taking account
of liquid crystal’s characteristics and represents color tone
close to its original image.
19
E
Basic Operation
n
Switching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDE
PC input
Displays image so it fills the entire screen.
AV input
An image with a 4:3 aspect ratio is stretched to fill the entire
screen.
ZOOM 1
PC input
An image with a 4:3 aspect ratio is enlarged to fill the entire screen
without changing the aspect ratio. The edges of the image may be
cut off.
AV input
ZOOM 2
PC input
Use this size if ZOOM 1 cuts off the subtitles.
AV input
NORMAL
PC input
Displays image so it fills the screen without changing the aspect
ratio of the input signals.
AV input
Displays the entire image of the aspect ratio of 4:3 without
changing the aspect ratio.
Dot by Dot
PC input
Displays the dots of the signals input from the connected PC as
the corresponding dots on the screen.
AV input
Displays the dots of the input signals as the corresponding dots on
the screen.
TIPS
• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial
or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright
Law, so please be careful.
• When “Enlarge” is set, the screen size is fixed to “WIDE” mode.
• When dual-screen display is selected, the screen size cannot be changed.
• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original
image (e.g. TV broadcast or video input from external equipment).
• When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this
monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen
size to “NORMAL”.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen
size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the
edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
20
E
Menu Items
Displaying the menu screen
Video and audio adjustment and settings of various functions
are enabled. This section describes how to use the menu
items. See pages 21 to 25 for details of each menu items.
Caution
• Do not turn the main power switch off while the menu items
are being displayed. Doing so may initialize the settings.
n
Example of operation
(Adjusting CONTRAST in the PICTURE menu)
1. Press
1. Press
MENU
to display the menu screen.
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 67.5 kHz
AUTO
CLOCK
PHASE
H-POS
H-POS
V-POS
H-SIZE
V-SIZE
H-RESOLUTION
H-SIZE
V-SIZE
H-RESOLUTION
V-RESOLUTION
RESET
RESET
SCREEN
PICTURE
AUDIO
SETUP
OPTION
PIP/PbyP
MULTI
600
25
610
37
50
50
50
1920
1080
1080
SCREEN
1/1
END···[MENU]
PC D-SUB
2. Press
or
to select PICTURE, and press
.
3. Press
or
to select CONTRAST.
AUTO
ANALOG GAIN
ANALOG OFFSET
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
RGB INPUT RANGE
64
86
31
30
30
30
30
12
1/2
FULL
PC D-SUB
PICTURE
SCREEN
PICTURE
AUDIO
SETUP
OPTION
PIP/PbyP
MULTI
OK···[MENU]
MOVE OSD···[DISPLAY]
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 67.5 kHz
4. Press
or
to adjust the setting.
▲
▲
▲
AUTO
ANALOG GAIN
ANALOG OFFSET
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
RGB INPUT RANGE
64
86
31
40
30
30
30
12
1/2
FULL
PC D-SUB
PICTURE
SCREEN
PICTURE
AUDI
OPTION
PIP/PbyP
MULTI
O
SETUP
OK···[MENU]
MOVE OSD···[DISPLAY]
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 67.5 kHz
For items that have
, press
, make settings and then
press
MENU
.
5. Press
MENU
twice to close the menu screen.
TIPS
• The menu will differ depending on the input mode.
• The menu screen will close automatically if no operation is
performed for about 15 seconds. (DATE/TIME SETTING,
SCHEDULE and LAN SETUP screens will close in about 4
minutes.)
n
Menu screen display
▲
▲
▲
AUTO
ANALOG GAIN
ANALOG OFFSET
BRIGHT
CONTRAST
BLACK LEVEL
TINT
COLORS
SHARPNESS
RGB INPUT RANGE
64
86
31
30
30
30
30
12
1/2
FULL
PC D-SUB
SCREEN
PICTURE
AUDIO
SETUP
OPTION
PIP/PbyP
MULTI
PICTURE
OK···[MENU]
MOVE OSD···[DISPLAY]
1 9 2 0 x 1 0 8 0
V: 60 Hz H: 67.5 kHz
1
2
3
4
1 Name of the menu
2 Input mode
3 An item being selected (highlighted)
4 Screen resolution of input signal, and other data.
TIPS
• Items that cannot be selected appear in gray.
(e.g. Function not supported by the current input signal)
n
Menu Items
The displayed menu items vary depending on whether or not
the PN-ZB01 (optional) is attached.
The following menus will be displayed only when the PN-ZB01
(optional) is attached.
the PN-ZB01 (optional) is attached.
The following menus will be displayed only when the PN-ZB01
(optional) is attached.
Menu
Item
SETUP
HOT PLUG CONTROL DVI
RS-232C/LAN SELECT
LAN SETUP
AUTO ASSIGN FIXED IP ADDR.
SPEAKER SELECT
RS-232C/LAN SELECT
LAN SETUP
AUTO ASSIGN FIXED IP ADDR.
SPEAKER SELECT
OPTION INPUT SELECT
DVI
BNC
BNC
AUDIO SELECT
PC DVI-D
PC D-SUB
PC RGB
AV DVI-D
AV COMPONENT (BNC)
AV COMPONENT (D-SUB)
AV S-VIDEO
AV VIDEO (BNC)
AV VIDEO (D-SUB)
PC D-SUB
PC RGB
AV DVI-D
AV COMPONENT (BNC)
AV COMPONENT (D-SUB)
AV S-VIDEO
AV VIDEO (BNC)
AV VIDEO (D-SUB)
PIP/PbyP PIP SOURCE
Click on the first or last page to see other PN-E702 (serv.man5) service manuals if exist.