Sharp PN-A601 (serv.man3) Service Manual ▷ View online
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
PN-A601 INSTALLATION, ADJUSTMENT, SETTING
2 – 6
■ CONTROLLING THE MONITOR WITH A PC
(LAN)
When the PN-ZB01 (optionel) is a attached, your monitor can be con-
nected to a LAN allowing you to control it from a PC on the LAN.
You can also configure the monitor to send e-mail notification when it
has a problem.
has a problem.
The connection requires a commercially available LAN cable (UTP
cable, Category 5, straight through).
MEMO
n
Your PC must be installed with Internet Explorer (version 7.0 or
later).
n
To control the monitor via LAN, set RS-232C/LAN SELECT to
LAN.
n
You cannot use RS-232C and LAN control simultaneously.
CAUTION
INITIALIZING PERSONAL INFORMATION
n
When the PN-ZB01 (optional) is attached, personal information
such as e-mail addresses can be registered in the monitor.
such as e-mail addresses can be registered in the monitor.
Before transferring or disposing of the monitor, initialize all set-
tings by selecting “ALL RESET1”. Note that “ALL RESET2” will
not initialize e-mail addresses and other settings.
not initialize e-mail addresses and other settings.
1 - 2.
CONNECTING THE POWER CORD
CAUTION
n
Do not use a power cord other than the one supplied with the
monitor.
1 ) Turn off the main power switch.
2 ) Plug the power cord (supplied) into the AC input terminal.
3 ) Plug the power cord (supplied) into the AC power outlet.
1 - 3. BINDING CABLES
The cables connected to the terminals on the rear of the monitor can be
fastened with the supplied cable clamp.
Insert the cable clamp into the cable clamp attachment on the rear of
the monitor and fasten the cables.
the monitor and fasten the cables.
Hub
LAN terminal
LAN cable (commercially available, straight)
Network (LAN)
1
2
3
Main power
switch
switch
AC input
terminal
terminal
Power cord
(Supplied)
(Supplied)
For power
outlet
outlet
: Cable clamp attachment
Cable
Cable clamp
attachment
attachment
Cable clamp
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
PN-A601 INSTALLATION, ADJUSTMENT, SETTING
2 – 7
1 - 4. REMOVING THE HANDLES
The handles can be removed.
The removed handles can be attached on the side.
1 ) Remove the handle screws and remove the handles and handle
spacers.
CAUTION
n
The handles and handle screws are for this monitor. Do not use
them for any other devices.
them for any other devices.
n
When attaching the handles, perform the steps for removing the
handles in reverse.
Always use this monitor’s handles, handle spacers, and handle
screws.
screws.
Also, be sure the handles are attached securely.
n
3Refer to page 6 - 2 "2. IDP FAN".
MEMO
n
To lower the height of the handles, attach the handles with the
handle spacers removed. To attach the handles with the handle
handle spacers removed. To attach the handles with the handle
spacers removed, secure the handles with the included handle
screws (short).
1 - 5. AFFIXING THE PROTECTION
COVERS AND PROTECTION
STICKERS
STICKERS
After installing the monitor, affix the included protection covers (2) as
necessary, and then apply the included protection stickers (2).
1 ) Affix the protection covers.
2 ) Apply the protection stickers.
Handle
Handle screws
Handle spacers
Handle spacers
Protection
cover
cover
Protection
sticker
sticker
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
PN-A601 INSTALLATION, ADJUSTMENT, SETTING
2 – 8
■ CONNECTION WITH THE CONTROL KIT (OPTIONAL)
CAUTION
n
When attaching the remote control sensor box, turn the main
power switch OFF.
power switch OFF.
n
Except for the remote control sensor box connection cable, do
not insert any other cable into the control kit terminal.
Also, do not connect any connection cables that have been
extended with commercially available cables.
extended with commercially available cables.
Insert the remote control sensor box connection cable into the control
kit terminal.
MEMO
n
When connecting the control kit, select whether to use the remote
control sensor and the brightness sensor on the remote control
control sensor and the brightness sensor on the remote control
sensor box or the monitor with CONTROL KIT SETTING on the
SETUP menu.
<WHEN ATTACHING THE REMOTE CONTROL SENSOR
BOX TO THIS MONITOR>
BOX TO THIS MONITOR>
Attach the remote control sensor box to the location shown in the fol-
lowing illustration.
1 ) Unscrew the mounting screw in the monitor’s remote control sen-
sor box mounting hole.
2 ) Secure the mounting bracket by screwing the mounting screw
removed in Step 1) in the monitor’s remote control sensor box
mounting hole.
mounting hole.
3 ) Adjust the angle of the remote control sensor box, and secure it
with the fixing screw, so that it may accurately receive signals from
the remote control unit.
MEMO
n
Depending on where it has been placed or the surrounding condi-
tions, the remote control sensor box may be affected by the
brightness of the main unit screen and the brightness sensor may
brightness of the main unit screen and the brightness sensor may
respond.
n
The brightness sensor may not function properly in extremely
bright or dark locations.
Connection cable
Control kit terminal
Remote control
sensor box
sensor box
FOR THE MONITOR IN
LANDSCAPE ORIENTATION
LANDSCAPE ORIENTATION
FOR THE MONITOR IN
PORTRAIT ORIENTATION
PORTRAIT ORIENTATION
Angle
adjustment
adjustment
Mounting bracket
Mounting screw
(Screw removed
from the remote
control sensor box
mounting hole)
(Screw removed
from the remote
control sensor box
mounting hole)
Fixing screw
Remote control
sensor box
sensor box
Remote control sensor box
mounting hole
mounting hole
CHAPTER 2. INSTALLATION, ADJUSTMENT, SETTING
PN-A601 INSTALLATION, ADJUSTMENT, SETTING
2 – 9
2. ADJUSTMENT
CAUTION
SCREEN DISPLAY FOR ADJUSTMENT
n
Before making adjustments in the SCREEN menu or PICTURE
menu, display an image to brighten the entire screen. If you are
using a Windows PC, use the adjustment pattern on the supplied
using a Windows PC, use the adjustment pattern on the supplied
CD-ROM.
OPENING THE ADJUSTMENT PATTERN
The following example is performed in Windows 7.
1 ) Load the supplied CD-ROM into the computer’s CD-ROM drive.
2 ) Open the CD-ROM in [My Computer].
In Windows XP, open [CD Drive] in [My Computer].
3 ) Double-click [Adj_uty.exe].
The adjustment pattern will appear.
Adjust the screen automatically or manually.
4 ) When adjustment is finished, press the [Esc] on the computer’s
keyboard to quit the adjustment program.
5 ) Eject the CD-ROM from the CD-ROM drive.
MEMO
n
If the display mode on the computer you are using is 65,000 col-
ors, the color levels in the color pattern may appear differently or
grayscale may appear to be colored.
grayscale may appear to be colored.
(This is due to the specifications of the input signal and is not a
malfunction.)
2 - 1. AUTOMATIC ADJUSTMENT
When you use the PC D-SUB input terminal or PC RGB input terminals
to display a PC screen for the first time, or when you change the setting
to display a PC screen for the first time, or when you change the setting
of the PC, use the automatic screen adjustment.
1 ) Switch the input to PC D-SUB or to PC RGB and display the adjust-
ment pattern. (See the description above.)
2 ) Press
and use
or
to display the SCREEN menu.
3 ) Press
and select “AUTO”.
4 ) Press
.
The automatic adjustment is complete in several seconds.
5 ) Press
twice to close the menu screen.
MEMO
n
If the screen cannot be adjusted properly with one automatic
adjustment, repeat the automatic adjustment two or three times.
Try manual adjustment if necessary.
Try manual adjustment if necessary.
2 - 2. INITIALIZATION (RESET)/FUNC-
TIONAL RESTRICTION SETTING
<THE REMOTE CONTROL UNIT>
*
1
Resets all the settings to the factory default settings.
When the unit is without PN-ZB01(optional), “ALL RESET” is dis-
When the unit is without PN-ZB01(optional), “ALL RESET” is dis-
played.
*
2
Returns all settings to the factory default settings except for the
following items.
following items.
LAN SETUP, RS-232C/LAN SELECT, ID No. SET, BAUD RATE,
NETWORK, MAIL, SERVICE & SUPPORT, and SNMP
When the unit is equipped with PN-ZB01 (optional), you can
When the unit is equipped with PN-ZB01 (optional), you can
make selections.
*
3
Normally, you do not need to change this setting.
When using an optional part, if instruction appears, change the
When using an optional part, if instruction appears, change the
setting accordingly.
CAUTION
NOTE FOR EXECUTING “ALL RESET 1”
n
Since the setting values related to LAN are initialized, do not use
in an environment with LAN.
n
When executing “ALL RESET 1” under the connected network
environment, be sure to disconnect the LAN cable before execu-
environment, be sure to disconnect the LAN cable before execu-
tion.
(This is because the operation is slowed and failed if there are
two or more sets of the initial state of IP address in a same net-
two or more sets of the initial state of IP address in a same net-
work.)
MENU
MENU
SIZE
MENU
ADJUSTMENT LOCK
OSD DISPLAY
ALL RESET
(ALL RESET1
(ALL RESET1
*1
/
ALL RESET2
*2
)
TEMPERATURE ALERT
STATUS ALERT
LED
(Adjust with
e
and
d
.)
ADJUSTMENT LOCK TARGET
(Adjust with
e
and
d
.)
RS-232C/LAN
(Adjust with
e
and
d
.)
(Adjust with
e
and
d
.)
(Adjust with
e
and
d
.)
(Adjust with
e
and
d
.)
(Adjust with
e
and
d
.)
POWER BUTTON
(Adjust with
e
and
d
.)
CONTROLLER INPUT
*3
(Adjust with
e
and
d
.)
END
(Press about 5 seconds until "F" is displayed in the
upper left area of the screen.)
Click on the first or last page to see other PN-A601 (serv.man3) service manuals if exist.