Sharp PN-60TB3 (serv.man4) Service Manual ▷ View online
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
OUTLINE OF THE PRODUCTS 1 - 12
3- 2. REMOTE CONTROL UNIT
No. Function
Contents
1 Signal
transmitter
2 POWER
button
3
MUTE
button
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back
to the previous level.
4
VOL +/-
buttons
Pressing or
displays the VOLUME menu
when the menu screen is not displayed.
Press or to adjust the volume of the sound.
* If you do not press any buttons for about 4
seconds, the VOLUME menu automatically
disappears.
* You can also change the setting by touch action.
BRIGHT
+/-
buttons
Pressing or displays the BRIGHT menu
when the menu screen is not displayed.
Press or to adjust the brightness.
* If you do not press any buttons for about 4
seconds, the BRIGHT menu automatically
disappears.
Cursor control ( / / / ) buttons
5
DISPLAY
button
Displays monitor information.
The display changes from INFORMATION1 ->
INFORMATION2 -> clear display, and so on every
time you press this button.
- The display disappears automatically after about 15
seconds.
- is displayed during LAN communication.
- If is displayed in red, there is a duplicate IP
address.
6
MODE
button
Each time you press this button, the color mode
changes in the following order:
- sRGB applies to PC input only.
sRGB is international standard of color
representation specified by IEC (International
Electrotechnical
Commission). Color conversion is made in taking
account of liquid crystal’s characteristics and
represents color tone close to its original image.
- HIGH ILLUMINANCE is a display with colors suited
to bright locations.
7
INPUT
button
The menu is displayed. Press or to select the
input mode, and press to enter.
TOUCH menu on the monitor button can change the
input mode.
- When the input mode is changed, the touch panel
connection also changes. You can set whether the
side or bottom USB port is used in each input mode.
*1 Select the terminal to be used in HDMI1 of INPUT
SELECT.
*2 Select the terminal to be used in HDMI2 of INPUT
SELECT.
*3 Select the terminal to be used in HDMI3 of INPUT
SELECT.
*4 Select the terminal to be used in D-SUB1 of
INPUT SELECT.
*5 Select the terminal for AUDIO SELECT which is
used for audio input.
Input mode
Video
Audio
DisplayPort DisplayPort
input
terminal
*5
HDMI1 HDMI1
input
terminal*1
HDMI2 HDMI2
input
terminal*2
HDMI3 HDMI3
input
terminal*3
D-SUB1 D-sub1
input
terminal*4
D-SUB2
D-sub2 input terminal
WHITEBOARD
WHITEBOARD
8
MENU
button
Displays and turns off the menu screen.
9
ENTER
button
Confirms the setting.
10
RETURN
button
Returns to the previous screen.
11
SIZE
button
The menu is displayed.
Press or to select the screen size.
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
OUTLINE OF THE PRODUCTS 1 - 13
■
Installing the batteries
1) Press the cover gently and slide it in the direction of the arrow.
2) S See the instructions in the compartment and put in the
supplied batteries (R-6 (“AA” size) x 2) with their plus (+) and
minus (-) sides oriented correctly.
3) Close the cover.
(MEMO)
• When the batteries become exhausted, replace them with new
(commercially available) batteries.
•The supplied batteries (R-6 (“AA” size) x 2) may become
exhausted quickly depending on how they are stored.
• If you will not be using the remote control for a long time, remove
the batteries.
• Use manganese or alkaline batteries only.
■
Remote control operation ranges
The operation range of the remote control unit is approx. 16.4 feet
(5 m) at an angle of approx 10° from the center to the
top/bottom/right/left of the remote control sensor.
(MEMO)
• Do not expose the remote control unit to shock by dropping or
stepping on it. This could lead to a malfunction.• Do not expose
the remote control unit to liquids, and do not place it in an area
with high humidity
• The remote control unit may not work properly if the remote
control sensor is under direct sunlight or strong lighting.
• Objects between the remote control unit and the remote control
sensor may prevent proper operation.
• Replace the batteries when they run low as this may shorten the
remote control’s operation range.
• If a fluorescet light is illuminated near the remote control unit, it
may interfere with proper operation.
• Do not use it with the remote control of other equipment such as
air conditioner, stereo components, etc.
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
OUTLINE OF THE PRODUCTS 1 - 14
3- 3. TOUCH PEN
PN-ZL01 : Touch pen + Pen adaptor
PN-ZL02 : Touch pen
Function button 1 : Right mouse click
Function button 2 : PageDown
Function button 3 : PageUP
State LED
Normal
state
Standby state
*1
LED is OFF
Function button is ON.
LED is ON
Pen tip is ON
LED is OFF
Special
state
Under pairing/Under selecting
the menu of driver
LED is flashing
(1)
*2
When the error is occurred
LED is flashing
(2)
*3
State for allowing the firmware
update
LED is ON
The data is being received or
updated
LED is flashing
(3)
*4
*1：Standby state ：Moves to the low power consumption without
pen operation for 60 seconds.
*2：LED is flashing (1)：1 second ON -> 1 second OFF) -> Repeat
this operation.
*3：LED is flashing (2)：0.5 seconds ON -> 0.5 seconds OFF ->
0.5 seconds ON -> 0.5 seconds OFF -> 0.5 seconds ON ->
3.5 seconds OFF -> Repeat this operation
*4：LED is flashing (3)：0.5 seconds ON -> 0.5 seconds OFF ->
Repeat this operation
■
Inserting the battery
1) Remove the battery cap.
2) Open the cover and insert the supplied battery (LR-03(“AAA”
size) into the touch pen.
Check the plus (+) and minus (-) markings on the inside
of the touch pen and insert the battery in the correct orientation.
3) Close the cover.
(MEMO)
• The supplied battery (LR-03 (“AAA” size)) may be exhausted in a
short time, depending on how it was stored.
• If the touch pen will not be used for an extended time, remove
the battery from the touch pen.
• For the battery, use an alkaline battery
.
■
Connecting the touch pen adapter
To use the touch pen, insert the touch pen adapter into the
touch pen adapter port on the monitor.
touch pen adapter port on the monitor.
PN-L703A/L703B, PN-70TA3/70TB3, PN-L603A/L603B, PN-60TA3/60TB3
OUTLINE OF THE PRODUCTS 1 - 15
4. SCREEN DISPLAY
4 – 1.DUAL SCREEN DISPLAY
It is possible to display two screens simultaneously.
Set this function with “PIP MODES” in the PIP/PbyP menu.
* The currently selected input signal is displayed on the main screen.
* The following combinations are available for display:
WHITEBOARD - DisplayPort
WHITEBOARD - HDMI1, HDMI2, HDMI3
DisplayPort - D-SUB1, D-SUB2
HDMI1, HDMI2, HDMI3 - D-SUB1, D-SUB2
PIP
A sub screen is displayed inside a main screen.
PbyP
A main screen and a sub screen are displayed in a line.
PbyP2
Displays a main screen which measures 1280 pixels in the longest
direction and a sub screen in a line.
(MEMO)
•
You might infringe on a copyright of the author which is protected by copyright law when you display the images of the computer screen
and television/VCR simultaneously for profit-making or to show the image to the public.
•
The screen size for dual-screen display is the same as the screen size for single-screen display. The Dot by Dot screen is displayed in
NORMAL size except when it is set as the PIP main screen.
•
When dual-screen display is selected, the SCREEN MOTION function is disabled.
•
When dual-screen display is selected, the CONNECT AUTO INPUT SELECT function and NO SIGNAL AUTO INPUT SEL. function
are disabled.
•
When dual-screen display is selected, the INPUT SELECT options cannot be set.
•
When dual-screen display is selected, the AUDIO menu cannot be set.
•
When an interlaced signal (1080i, 480i, video) is input to the sub screen, horizontal lines may flicker. If this happens, display the image
on the main screen.
Click on the first or last page to see other PN-60TB3 (serv.man4) service manuals if exist.