DOWNLOAD Sharp LL-T1815 (serv.man13) Service Manual ↓ Size: 3.61 MB | Pages: 127 in PDF or view online for FREE

COOL ..... Color tone bluer than standard
   • ........... Color tone slightly bluer than standard
STD ........ Color tone standard setting
   • ........... Color tone slightly redder than standard
WARM .... Color tone redder than standard
USER

R-CONTRAST ........

  button for blue-green
  button for red

G-CONTRAST ........

  button for purple
  button for green

B-CONTRAST .........

  button for yellow
  button for blue

GAMMA
Adjust so that dark and bright images are easy to
see. If the screen is dark and hard to see, increase
the numerical value. If it is bright and hard to see,
lower the numerical value. (    buttons)

MODE SELECT - 1

INFORMATION

OFF TIMER
INPUT-2

1LINE

2LINES

INPUT-1

ANALOG

1280  x 1024

V : 60Hz

H : 64kHz

Notes:
- To choose a menu option: 

 button

- To go to the next menu: MENU button

INFORMATION
A model name (MODEL), a serial no. (S/N), and
usage time (USAGE TIME) of the display can be
checked.
After selecting [INFORMATION], press the 
button (Checking done: MENU button)

OFF TIMER
Power is automatically shut off when the set time
elapses.
After selecting [OFF TIMER], press the   button

and set [ON] / [OFF] by pressing the     buttons.
If selecting [ON], press the 

 button and set the

shut-off time by pressing the     buttons. (Be-
tween 1 and 23 hours may be set, by the
hour.)(Setting done: MENU button)
- When [ON] is selected, the remaining time is

displayed in the upper right of the screen during
the last 5 minutes before the shut-off. (The
remaining time is displayed for approx. 5
seconds, on each minute)

- To clear automatic shut-off temporarily, press the

power button between the display of remaining
time and the shut-off of power.
To subsequently turn the power off, press the
power button again. (When next turning on
power, power is again automatically shut off
when the set time elapses.)

INPUT-2
Set [1 LINE] when connecting digital or analog
signal cables to a DVI-I input terminal (INPUT-2) on
the display.
Set [2LINES] when connecting a 2-input cable.

(    buttons)
- If the connections and settings are not correctly

set, the screen will not be correctly displayed.

400 LINES (degree of resolution)
You can specify the horizontal resolution of a 400-
line screen when using US text, etc. (    buttons)

640: 640 X 400 dot mode
720: 720 X 400 dot mode (US text etc.)

Note:
- As the resolution input for other than 400 lines is

done automatically, there is no need to set it.

MODE SELECT - 2

OSD

LANGUAGE
EXPAND

OFF

ON1

ON2

SCARING

1

400LINES

640

720

INPUT-1

ANALOG

1280  x 1024

V : 60Hz

H : 64kHz

Notes:
- Depending on the resolution of the input signal,

even if menu options can be selected, the display
may not change.

- To choose a menu option: 

 button

- When adjustment complete: MENU button

OSD
After selecting [OSD], press the   button.

The position of the OSD display can be moved

to the left and right. (    buttons)

The position of the OSD display can be moved
up and down. (    buttons)

The orientation of the OSD display can be
changed.(    buttons)

ON: Orientation for long height display
OFF: Orientation for long width display

LANGUAGE
Messages displayed on the screen and OSD Menu
contents can be changed to the following languages.

1.After selecting [LANGUAGE], press the   button.
2.Select the desired language using the 

 button.

3.Press the MENU button.

EXPAND (Screen expansion)
For display modes of less than 1280 X 1024 pixels,
the display can be expanded if desired. (  
buttons)

OFF: Expansion off
ON1: Using the fixed aspect ratio, the entire

screen is enlarged.

ON2: The entire screen is enlarged.

Note:
- If a resolution of 1280 X 1024 pixels cannot be

achieved even after expansion is attempted, the
screen’s perimeter will display black. (This is not
a malfunction.)

SCALING (Level of scaling)
If [EXPAND] is set on [ON1] or [ON2], the sharp-

ness of the image can be adjusted.  (    buttons)

Adjustments can be made using On Screen
Display (OSD) Menu provided.

If you are using Windows, open the Adjustment
Pattern on the accompanying CD-ROM. (p. 18)
If your system is not Windows, you can not use the
Adjustment Pattern. Therefore display an image
that makes the entire screen light and adjust it
through checking visually its actual tone.
This chapter provides the procedure how to adjust
the screen by using Adjustment Pattern (for
Windows)

1.Press the MENU button.

The COLOR CONTROL Menu will be displayed.

COLOR CONTROL

COLOR MODE

sRGB

STD

VIVID

WHITE BALANCE
GAMMA

INPUT-2

DIGITAL

1280  x 1024

V : 60Hz

H : 64kHz

2.Select item to be adjusted by pressing the MENU

button.
Each time the MENU button is pressed the next
menu is selected. (COLOR CONTROL 

→ MODE

SELECT-1 

→ MODE SELECT-2 → OSD Menu

disappears)

Note:
- The OSD Menu automatically disappears

approximately 30 seconds after the last
command.

COLOR CONTROL

COLOR MODE

sRGB

STD

VIVID

WHITE BALANCE
GAMMA

INPUT-2

DIGITAL

1280  x 1024

V : 60Hz

H : 64kHz

Notes:
- To choose a menu option: 

 button

- To go to the next menu: MENU button

COLOR MODE
Color tone can be set as below.

STD ......... Displays image with the color tone

results from original scheme of liquid
crystal panel.

sRGB ....... sRGB is international standard of

color representation specified by IEC
(International Electrotechnical
Commission). Color conversion is
made in taking account of liquid
crystal’s characteristics and repre-
sents color tone close to it original
image.

VIVID ....... Displays an image with dynamic and

VIVID primary colors.

Subsequent items can be set when the [COLOR
MODE] is [STD].

After selecting [WHITE BALANCE], press the 
button and display the adjustment menu.

WHITE BALANCE

COOL

STD

WARM

USER

R-CONTRAST
G-CONTRAST
B-CONTRAST

OK

<MENU>

Notes:
- On settings other than [STD] not all graduations

can be displayed. To display all graduations, set
to [STD].

- Use the     buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting USER will display the setting values for

[R-CONTRAST], [G-CONTRAST] and [B-
CONTRAST], in order to make fine adjustments.

- Use the 

 button to select

[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST].

- When adjustment complete: MENU button

MODE SELECT - 1

INFORMATION

OFF TIMER
INPUT-2

1LINE

2LINES

INPUT-2

DIGITAL

1280  x 1024

V : 60Hz

H : 64kHz

Notes:
- To choose a menu option: 

 button

- To go to the next menu: MENU button

INFORMATION
A model name (MODEL), a serial no. (S/N), and
usage time (USAGE TIME) of the display can be
checked.
After selecting [INFORMATION], press the 
button (Checking done: MENU button)

OFF TIMER
Power is automatically shut off when the set time
elapses.
After selecting [OFF TIMER], press the   button

and set [ON] / [OFF] by pressing the     buttons.
If selecting [ON], press the 

 button and set the

shut-off time by pressing the     buttons. (Be-
tween 1 and 23 hours may be set, by the
hour.)(Setting done: MENU button)
- When [ON] is selected, the remaining time is

displayed in the upper right of the screen during
the last 5 minutes before the shut-off. (The
remaining time is displayed for approx. 5
seconds, on each minute)

- To clear automatic shut-off temporarily, press the

power button between the display of remaining
time and the shut-off of power.
To subsequently turn the power off, press the
power button again. (When next turning on
power, power is again automatically shut off
when the set time elapses.)

INPUT-2
Set [1 LINE] when connecting digital or analog
signal cables to a DVI-I input terminal (INPUT-2) on
the display.
Set [2LINES] when connecting a 2-input cable.

(    buttons)
- If the connections and settings are not correctly

set, the screen will not be correctly displayed.

COOL ..... Color tone bluer than standard
   • ........... Color tone slightly bluer than standard
STD ........ Color tone standard setting
   • ........... Color tone slightly redder than standard
WARM .... Color tone redder than standard
USER

R-CONTRAST ........

  button for blue-green
  button for red

G-CONTRAST ........

  button for purple
  button for green

B-CONTRAST .........

  button for yellow
  button for blue

GAMMA
Adjust so that dark and bright images are easy to
see. If the screen is dark and hard to see, increase
the numerical value. If it is bright and hard to see,
lower the numerical value. (    buttons)