DOWNLOAD Sony SAL20TC Service Manual ↓ Size: 715.32 KB | Pages: 26 in PDF or view online for FREE

Model
SAL20TC
Pages
26
Size
715.32 KB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera
File
sal20tc.pdf
Date

Sony SAL20TC Service Manual ▷ View online

SERVICE NOTE
SPECIFICATIONS
REPAIR PARTS LIST
DISASSEMBLY
ADJUSTMENTS
SERVICE MANUAL
Link
Link
Revision History
Revision History
How to use
Acrobat Reader
How to use
Acrobat Reader
Sony EMCS Co.
SAL20TC (2x TELE CONVERTER) (2 X Teleconverter)
Ver. 1.3  2008.12
LENS FOR DSLR CAMERA
2008L0800-1
  © 2008.12
Published by Kohda TEC
9-852-107-14
US Model
Canadian Model
AEP Model
Chinese Model
SAL20TC
(2x TELE CONVERTER) (2 X Teleconverter)
Revised-3
Replace the previously issued
SERVICE MANUAL 9-852-107-13
with this Manual.
— 2 —
SAL20TC (2x TELE CONVERTER) (2 X Teleconverter)
SPECIFICATIONS
Effective focal length
2.0X that of the attched lens
f-stop
 
*
1
2 f-stop higher from that of the attached lens
*
1
When 135mm F2.8 [T4.5] STF (SAL135F28) is attached, a 2 stop increase of the T-number (T No.).
Lens groups/elements
6 elements in 5 groups
Minimum focus (m (feet))
 
*
2
Same as that of the attached lens
*
2
Minimum focus is the shortest distance from the image sensor to the subject.
Maximum magnification (
×××××
)
2.0X that of the attached lens
Depth of field
Approx. 1/2 that of the attached lens
Dimensions (maximum diameter 
×××××
 height) (mm (in.))
Approx. 64 
× 43.5 (2  1/2 × 1  11/16)
Mass (g (oz.))
Approx. 200 (7  1/16)
Included items
Teleconverter (1), Front lens cap (1), Rear lens cap (1), Lens case (1), Set of printed documentation
Designs and specifications are subject to change without notice.
— 3 —
SAL20TC (2x TELE CONVERTER) (2 X Teleconverter)
TABLE OF CONTENTS
Section
Title
Page
1.
SERVICE NOTE
1-1.
Chemicals ······································································· 1-1
1-2.
Exterior Parts ·································································· 1-1
1-3.
Unleaded Solder ····························································· 1-1
1-4.
Safety Check-out ···························································· 1-2
1-5.
Troubleshooting ····························································· 1-3
2.
DISASSEMBLY
2-1.
Disassembly ··································································· 2-2
3.
REPAIR PARTS LIST
3-1.
Exploded Views ······························································ 3-1
3-2.
Supplied Accessories ······················································ 3-3
4.
ADJUSTMENTS
4-1.
Preparations ···································································· 4-1
4-2.
Preset Lever Position Check and Adjustment ················ 4-2
4-3.
Flange Back (f’F) Check/Adjustment ···························· 4-3
SAL20TC (2x TELE CONVERTER) (2 X Teleconverter)
1-1
1. SERVICE NOTE
1-1.
Chemicals
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health and environment, and wastes resources.
Manage the chemicals carefully as follows.
• Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.
• Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.
• Keep containers sealed to avoid natural evaporation when chemicals are not in use.
• Avoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and
use up it.
1-2.
Exterior Parts
Be careful to the following points for exterior parts used in this unit.
• Use a piece of cleaning paper or cleaning cloth for cleaning exterior parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.
• Insert the specific screws vertically to the part when installing a exterior part.
Be careful not to tighten screws too much.
1-3.
Unleaded Solder
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.
(
Caution:
Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 
°C approximately.
If cannot control temperature, solder/unsolder at high temperature for a short time.
Caution:
The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing
unleaded solder and leaded solder will cause detachment phenomenon.
Page of 26
Display

Sony SAL20TC Service Manual ▷ Download

  • DOWNLOAD Sony SAL20TC Service Manual ↓ Size: 715.32 KB | Pages: 26 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony SAL20TC in PDF for free, which will help you to disassemble, recover, fix and repair Sony SAL20TC Digital Camera. Information contained in Sony SAL20TC Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.