Sharp LL-T1511A (serv.man25) User Manual / Operation Manual ▷ View online
25
English
4. Remove the connector cover.
Remove the screws and lift it upward.
5. Remove the DC connector 5.
6. Remove the DC cord from its hook 6.
6. Remove the DC cord from its hook 6.
7. Remove the screws fixing the connector holder
and remove the connector holder 7.
8. Remove the signal cable from the cord holder
inside the stand 8.
Instructions for installing a VESA compliant arm
An arm or stand based on the VESA standard
(purchased separately) can be attached to the
monitor. To install the arm an AC adapter (purchased
separately) is required.
(purchased separately) can be attached to the
monitor. To install the arm an AC adapter (purchased
separately) is required.
When choosing the arm to be installed take note of
the following points.
•
the following points.
•
The arm should be compatible with the VESA
standard, and there must be a gap of at least
75 mm x 75 mm between the screw holes on the
section to be attached.
standard, and there must be a gap of at least
75 mm x 75 mm between the screw holes on the
section to be attached.
•
The arm must not fall off or break off after being
attached to the monitor.
attached to the monitor.
If an arm is attached, a USB hub cannot be used.
(This is because the arm is installed inside the
monitor stand.)
(This is because the arm is installed inside the
monitor stand.)
Please be careful not to hurt your fingers or injure
yourself.
1. Turn off the main power switch and remove the
yourself.
1. Turn off the main power switch and remove the
power plug.
2. Remove the rear cover.
Place your hand on the upper opening of the rear
cover 1 and pull it upward 2.
cover 1 and pull it upward 2.
3. Remove the stand cover.
Pull the stand cover upward to remove it 3.
If removal is difficult, place a finger inside the
lower opening 4 and lift it.
If removal is difficult, place a finger inside the
lower opening 4 and lift it.
1
2
3
4
6
5
7
8
Rear cover
Stand cover
Connector cover
DC connector
LL-T1511-01A_gb.p65
2/14/01, 9:00 AM
25
26
9. Being careful not to damage the monitor, spread
out a soft cloth and lay the monitor on it display-
side down.
side down.
10.Remove the four screws and then remove the
stand from the monitor.
11.Attach the arm to the monitor with four screws.
12.Connect the AC adapter (purchased separately).
Connect the AC adapter's DC plug to the AC
adapter's connection terminal 9, and place the
cord inside the cord hook 0.
Coonect the power cord to the AC adapter q,
and connect the AC plug to the AC outlet w.
adapter's connection terminal 9, and place the
cord inside the cord hook 0.
Coonect the power cord to the AC adapter q,
and connect the AC plug to the AC outlet w.
9
0
q
w
Information
The stand is specially made for use with this
monitor. Once having removed the stand, never
attempt to attach it to another device.
Once having removed the screws, store them
together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to malfunc-
tion.
The stand is specially made for use with this
monitor. Once having removed the stand, never
attempt to attach it to another device.
Once having removed the screws, store them
together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to malfunc-
tion.
Information
The screws used to
attach the arm should be
M4 screws with a length
of 4 ~ 6 mm protruding
from the surface to be
attached. Using any
other kind of screw may
lead to the monitor
falling off or damage to
the internal part of the
monitor.
The screws used to
attach the arm should be
M4 screws with a length
of 4 ~ 6 mm protruding
from the surface to be
attached. Using any
other kind of screw may
lead to the monitor
falling off or damage to
the internal part of the
monitor.
AC adapter connection terminal
4 ~ 6 mm
Screw used to
attach arm
attach arm
Arm
Part of monitor
to which arm is
attached
to which arm is
attached
Instructions for installing a VESA compliant arm
LL-T1511-01A_gb.p65
2/14/01, 9:00 AM
26
26
9. Being careful not to damage the monitor, spread
out a soft cloth and lay the monitor on it display-
side down.
side down.
10.Remove the four screws and then remove the
stand from the monitor.
11.Attach the arm to the monitor with four screws.
12.Connect the AC adapter (purchased separately).
Connect the AC adapter's DC plug to the AC
adapter's connection terminal 9, and place the
cord inside the cord hook 0.
Coonect the power cord to the AC adapter q,
and connect the AC plug to the AC outlet w.
adapter's connection terminal 9, and place the
cord inside the cord hook 0.
Coonect the power cord to the AC adapter q,
and connect the AC plug to the AC outlet w.
9
0
q
w
Information
The stand is specially made for use with this
monitor. Once having removed the stand, never
attempt to attach it to another device.
Once having removed the screws, store them
together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to malfunc-
tion.
The stand is specially made for use with this
monitor. Once having removed the stand, never
attempt to attach it to another device.
Once having removed the screws, store them
together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to malfunc-
tion.
Information
The screws used to
attach the arm should be
M4 screws with a length
of 4 ~ 6 mm protruding
from the surface to be
attached. Using any
other kind of screw may
lead to the monitor
falling off or damage to
the internal part of the
monitor.
The screws used to
attach the arm should be
M4 screws with a length
of 4 ~ 6 mm protruding
from the surface to be
attached. Using any
other kind of screw may
lead to the monitor
falling off or damage to
the internal part of the
monitor.
AC adapter connection terminal
4 ~ 6 mm
Screw used to
attach arm
attach arm
Arm
Part of monitor
to which arm is
attached
to which arm is
attached
Instructions for installing a VESA compliant arm
LL-T1511-01A_gb.p65
2/14/01, 9:00 AM
26
26
9. Being careful not to damage the monitor, spread
out a soft cloth and lay the monitor on it display-
side down.
side down.
10.Remove the four screws and then remove the
stand from the monitor.
11.Attach the arm to the monitor with four screws.
12.Connect the AC adapter (purchased separately).
Connect the AC adapter's DC plug to the AC
adapter's connection terminal 9, and place the
cord inside the cord hook 0.
Coonect the power cord to the AC adapter q,
and connect the AC plug to the AC outlet w.
adapter's connection terminal 9, and place the
cord inside the cord hook 0.
Coonect the power cord to the AC adapter q,
and connect the AC plug to the AC outlet w.
9
0
q
w
Information
The stand is specially made for use with this
monitor. Once having removed the stand, never
attempt to attach it to another device.
Once having removed the screws, store them
together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to malfunc-
tion.
The stand is specially made for use with this
monitor. Once having removed the stand, never
attempt to attach it to another device.
Once having removed the screws, store them
together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to malfunc-
tion.
Information
The screws used to
attach the arm should be
M4 screws with a length
of 4 ~ 6 mm protruding
from the surface to be
attached. Using any
other kind of screw may
lead to the monitor
falling off or damage to
the internal part of the
monitor.
The screws used to
attach the arm should be
M4 screws with a length
of 4 ~ 6 mm protruding
from the surface to be
attached. Using any
other kind of screw may
lead to the monitor
falling off or damage to
the internal part of the
monitor.
AC adapter connection terminal
4 ~ 6 mm
Screw used to
attach arm
attach arm
Arm
Part of monitor
to which arm is
attached
to which arm is
attached
Instructions for installing a VESA compliant arm
LL-T1511-01A_gb.p65
2/14/01, 9:00 AM
26
