DOWNLOAD Sharp LL-H1813 (serv.man6) Service Manual ↓ Size: 580.98 KB | Pages: 32 in PDF or view online for FREE

LCD display

46 cm measured diagonally
Advanced Super-V and Anti Glare Low Reflection
TFT LCD module

Resolution (max.)

SXGA 1280 x 1024 pixels

Displayable colors (max.)

16.77 million colors (8 bit)

Brightness (max.)

220cd/m

2

Dot pitch

0.2805(H) x 0.2805(V) mm

Contrast ratio

400:1

Angle of visibility

Left-right 170°; Up-down 170°

Screen display size

Horizontal 359 mm x Vertical 287.2 mm

Video signal

Analog: Analog RGB (0.7Vp-p) [75

Ω]

Digital: DVI standard based on 1.0

Sync signal

H/V Separate Sync (TTL level: +/-), Sync on
Green, Composite Sync (TTL level: +/-)

Expansion compensation

Digital screening (enlargement VGA/SVGA/XGA
etc. to full screen size.)

Plug & Play

VESA DDC2B compatible

Power management

VESA: based on DPMS
DVI:

based on DMPM

Input signal terminal

DVI-I 29 pin x 2

USB hub function

1 upstream port, 2 downstream ports
(selfpowered hub based on USB standard Rev
1.1)

Audio input terminal

Mini stereo jack

Headphone terminal

Mini stereo jack

Power supply

AC100 - 240V, 50/60Hz

Temperature of operating environment

5 - 35°C

Power consumption

51W (Not using USB hub)
(57W maximum, 5W when in power-saving
mode)

Dimensions (W x D x H) (Units: mm)

395 x 68 x 324

Weight

Approx. 5.7kg

395

68

324

Digital signal cable:

Approx. 2.0 m

USB cable:

Approx. 2.0 m

Audio cable:

Approx. 2.0 m

640x480

800x600

1024x768

1152x864
1280x960

1280x1024

720x400
640x480
832x624

1024x768
1152x870

1280x1024

1024x768

1152x900

1280x1024

31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
60.0kHz
64.0kHz
80.0kHz
31.5kHz
35.0kHz
49.7kHz
60.2kHz
68.7kHz
64.0kHz
80.0kHz
48.3kHz
53.6kHz
56.6kHz
61.8kHz
71.8kHz
71.7kHz
81.1kHz

60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
70Hz
75Hz
75Hz
60Hz
60Hz
75Hz
70Hz

66.7Hz
74.6Hz

75Hz
75Hz
60Hz
75Hz
60Hz
66Hz
70Hz
66Hz

76.2Hz
67.2Hz

76Hz

25.175MHz

31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
65.0MHz
75.0MHz

78.75MHz
108.0MHz
108.0MHz
108.0MHz
135.0MHz

28.3MHz
30.2MHz
57.3MHz
80.0MHz

100.0MHz
108.0MHz
135.0MHz
64.13MHz

70.4MHz

74.25MHz
94.88MHz

108.23MHz
117.01MHz
134.99MHz

- Recommended resolution is 1280 x 1024.
- All are compliant only with non-interlaced.
- Frequencies for Power Macintosh and Sun Ultra

series are reference values. To connect, another
adapter (commercially available) may be
required.

- If the monitor is receiving timing signals that are

not compatible, [OUT OF TIMING] will appear.
Follow your computer’s instruction manual to set
the timing so that it is compatible with the
monitor.

- If the monitor is not receiving any signal (synch

signal), [NO SIGNAL] will appear.

640x480

800x600

1024x768

1152x864
1280x960

1280x1024

720x400

31.5kHz
37.9kHz
37.5kHz
37.9kHz
48.1kHz
46.9kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
60.0kHz
64.0kHz
31.5kHz

60Hz
72Hz
75Hz
60Hz
72Hz
75Hz
60Hz
70Hz
75Hz
75Hz
60Hz
60Hz
70Hz

25.175MHz

31.5MHz
31.5MHz
40.0MHz
50.0MHz
49.5MHz
65.0MHz
75.0MHz

78.75MHz
108.0MHz
108.0MHz
108.0MHz

28.3MHz

- Recommended resolution is 1280 x 1024.
- All are compliant only with non-interlaced.
- For a digital signal input, it can be connected to a

computer with a DVI-compatible output terminal
(DVI-D24 pin or DVI-I29 pin) and which has
SXGA output ability. (Depending on the computer
to be connected, correct display may or may not
be possible.)

- If the monitor is receiving timing signals that are

not compatible, [OUT OF TIMING] will appear.
Follow your computer’s instruction manual to set
the timing so that it is compatible with the
monitor.

- If the monitor is not receiving any signal (synch

signal), [NO SIGNAL] will appear.

(DVI-I connector with 29 pins)

The monitor is based on the VESA DPMS and the DVI DMPM standards.
To activate the monitor's Power Management function, both the video card and the computer must
conform to the VESA DPMS standard and the DVI DMPM standard.

DPMS: Display Power Management Signalling

                                                   *Not using USB hub

DMPM: Digital Monitor Power Management

                                      *Not using USB hub

This monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for carrying out Plug & Play functions on the monitor or PC. It transfers informa-
tion such as degree of resolution between the monitor and PC. You can use this function if your PC is
DDC compliant and if it is set so that it can detect the Plug & Play monitor.
There are many varieties of DDC due to the differences between systems. This monitor works with
DDC2B.

DPMS mode

Screen

Power

H-sync V-sync

consumption

ON

Display on

51W*

Yes

Yes

STANDBY

No

Yes

SUSPEND

Display off

5W

Yes

No

OFF

No

No

DMPM mode

Screen

Power

consumption

ON

Display on

51W*

OFF

Display off

5W

No.

Function

No. Function

1

TMDS data 2-

16

Hot plug detection

2

TMDS data 2+

17

TMDS data 0-

3

TMDS data 2/4 shield

18

TMDS data 0+

4

N.C.

19

TMDS data 0/5 shield

5

N.C.

20

N.C.

6

DDC clock

21

N.C.

7

DDC data

22

TMDS clock shield

8

23

TMDS clock +

9

TMDS data 1-

24

TMDS clock -

10 TMDS data 1+

C1

Analog red image signal

11 TMDS data 1/3 shield

C2

Analog green image signal

12 N.C.

C3

Analog blue image signal

13 N.C.

C4

14 +5V

C5

Analog GND

15 GND

Analog vertically synchronised
signal

Analog horizontally synchro-
nised signal

Depending on the computer or OS, it may be
necessary to use the computer to operate the
installation of monitor set-up information etc. If so,
follow the steps below to install the monitor set-up
information. (Depending on the type of computer or
OS, command names and methods may differ.
Please follow the computer’s own operation manual
while reading this.)

About the ICC profile
An ICC (International Color Consortium) profile
is a file that describes the color characteristics
of the LCD monitor. By using an application that
works together with an ICC profile, a high color
resolution can be realized.
- Windows98/2000/Me/XP all use the ICC

profile.

- When installing Windows98/2000/Me/XP set-

up information (described below), the ICC
profile is also installed. If you would like to
install  the ICC program only, please refer to
Installing the ICC profile on page 26.

- When using an ICC profile, set  [COLOR

MODE] and [WHITE BALANCE] to [STD], and
set [HUE] and [SATURATION] to [0].

Installing monitor set-up information into Win-
dows95.
This explanation assumes that the floppy disk drive
is "A drive".
1. Place the Utility Disk into the computer's A

drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced Properties], and

[Monitor], then [Change].

5. Click on [Have disk], confirm that [Copy

manufacturer's files from:] is [A:] then click [OK].

6. Confirm that the monitor details are selected,

and click [OK].

7. Check that the monitor details are displayed,

then click [Apply].

8. Click [OK], and close the window.
9. Remove the Utility Disk from the A drive.

Installing monitor set-up information into Win-
dows98, and setting the monitor's ICC profile as a
predetermined value.
This explanation assumes that the floppy disk drive
is "A drive".

If the "Add new Hardware Wizard" has appeared:
1. Place the Utility Disk into the computer's A

drive.

2. Click [Next].
3. Check [Display a list of all the drivers in a

specific location, so you can select the driver
you want.], then click [Next].

4. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files
from:] is [A:], and click [OK].

5. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish]. If the "Add
New Hardware Wizard" appears, repeat the
installation commands beginning from 2 above.

6. Remove the Utility Disk from the A drive.

If the "Add New Hardware Wizard" has not ap-
peared:
1. Place the Utility Disk in the computer's A drive.
2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Click [Next].
7. Click on [Display a list of all the drivers in a

specific location, so you can select the driver
you want.], then click [Next].

8. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files
from:] is [A:], and click [OK].

9. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish].

10. Check that the monitor details are displayed,

then click [Apply].

11. Click [OK], and close the window.
12. Remove the Utility Disk from the A drive.