DOWNLOAD Sharp LL-H1813 (serv.man6) Service Manual ↓ Size: 580.98 KB | Pages: 32 in PDF or view online for FREE

For analog signal
1.First perform an automatic adjustment. (p. 14)
2.Perform manual adjustment where necessary.

(p. 15)

The monitor can generally be used without
adjustment. If necessary perform manual
adjustment. (p. 18)

Note:
- All adjustments will be saved even after turning

the power off.

All adjustment values can be returned to their
original ex-factory values in one command.
1. Turn off the monitor power.
2. Press the MENU button and the SELECT button

simultaneously, and while doing this press the
power button (i.e. turn the power on).
When [ALL RESET] appears on the screen, the
reset is complete.

Notes:
- While ALL RESET is displayed, the control

buttons are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the
adjustment lock before attempting to operate
control buttons.

The adjustment values of the analog signal time’s
ADJUSTMENT menu can be returned to their
original ex-factory values.
1. Turn on the monitor power.
2. Press the MENU button and the   button

simultaneously.
When [RESET] appears on the screen, the reset
is complete.

Note:
- It is not possible to reset values when the

adjustment lock is in place. Remove the
adjustment lock before attempting to operate
control buttons.

By disabling the control buttons (i.e. setting the
lock) any attempted changes to adjusted values will
be voided.
1. Turn off the monitor power.
2.While pressing the MENU button, press the

power button (i.e. turn the power on).
Continue to press the button until [ADJUSTMENT
LOCKED] appears on the screen. The lock is set
when the message is displayed.

Note:
- When the lock is in place, all buttons other than

the power button are disabled.

1. Turn off the monitor power.
2.While pressing the MENU button, press the

power button (i.e. turn the power on).
Continue to press the button until [ADJUSTMENT
UNLOCKED] appears on the screen. The lock is
released when the message is displayed.

Carry out the commands without the On Screen
Display (OSD) Menu displayed. If the OSD Menu is
displayed, press the MENU button (several times
may be required) and begin when the OSD Menu
has disappeared.
1. Without the OSD Menu being displayed, push the

 or the   button.

2. Adjust by pressing the   button (darker) or 

button (lighter).

Note:
- On Screen display for adjustment disappears

several seconds after the last operation.

A model name, a serial number, and usage time
can be checked.

1. Turn off the monitor power.
2. Press the SELECT button and the   button

simultaneously, and while doing this press the
power button (i.e. turn the power on).

3.Confirmation finished: MENU button.

Note:
- [USAGE TIME] will not be set to [0] due to the

delivery inspection time at factories, etc.

Options in the ADJUSTMENT Menu can be
adjusted automatically (CLOCK, PHASE, H-POS,
V-POS).

Note:
- When setting up this monitor for the first time or

after having changed an aspect of the current
system, perform an automatic screen adjustment
before use.

First display an image that makes the entire screen
light.
If you are using Windows, you can use the Adjust-
ment Pattern on the Utility Disk.

Opening the Adjustment Pattern (for Windows)
This explanation is for Windows 95/98/Me/2000/XP,
and assumes that the floppy disk drive is "A drive".
- If you are using the Floppy disk other than [Drive

A],read [Drive A] or [A:] in replacing them with
the drive name in use currently.

1.Place the Utility Disk into the computer’s A drive.
2.Open [My Computer] and select [3 ½ Floppy [A:]].

If using Windows 3.1, open [File Manager] and
choose "A drive".

3.Double click on [Adj_uty.exe] to run the

Adjustment Program. The Adjustment Pattern will
appear.

Adjustment pattern

After completing the adjustments, press the
computer’s [Esc] key to exit the Adjustment
Program.

Note:
- If your computer’s display mode is set to 65K

colors, you may see the different color levels in
each color pattern or the gray scale may look
colored. (This is due to the specification of the
input signal and is not a malfunction.)

1.Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

CLOCK
PHASE
H-POS
V-POS

127

6

149

41

MANUAL

AUTO

INPUT-1

ANALOG

1280 x 1024

V : 60Hz

H : 64kHz

2.Press the   button.

The screen will become dark and [ADJUSTING]
will be displayed. After a few seconds the
ADJUSTMENT Menu will return. (The automatic
adjustment is now complete.)

3.Press the MENU button 4 times to make the OSD

Menu disappear.

Notes:
- In most cases automatic adjustment is sufficient.
- If necessary due to any of the following, manual

adjustments (p. 15) can be performed after the
automatic adjustment.
- When further fine adjustment is needed.
- When the computer’s video input signals are

Composite Sync or Sync On Green. (Automatic
adjustments may not be possible.)

- When [OUT OF ADJUST] is displayed. (When

the screen displays an entirely dark image, the
automatic screen adjustment may be disabled.
When making an automatic adjustment, be
sure to either use the Adjustment Pattern or try
displaying an image that makes the entire
screen very bright.)

Adjustments can be made using On Screen
Display (OSD) Menu provided.

If you are using Windows, open the Adjustment
Pattern on the Utility Disk. (p. 14)
If your system is not Windows, you can not use the
Adjustment Pattern. Therefore display an image
that makes the entire screen light and adjust it
through checking visually its actual tone.
This chapter provides the procedure how to adjust
the screen by using Adjustment Pattern (for
Windows)

1.Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

CLOCK
PHASE
H-POS
V-POS

127

6

149

41

MANUAL

AUTO

INPUT-1

ANALOG

1280 x 1024

V : 60Hz

H : 64kHz

At this point relevant menu options can be
adjusted.
Each time the MENU button is pressed the next
menu is selected. (ADJUSTMENT 

→ GAIN

CONTROL 

→ COLOR CONTROL → MODE

SELECT 

→ OSD Menu disappears)

Note:
- The OSD Menu automatically disappears

approximately 30 seconds after the last
command.

ADJUSTMENT

CLOCK
PHASE
H-POS
V-POS

127

6

149

41

MANUAL

AUTO

INPUT-1

ANALOG

1280 x 1024

V : 60Hz

H : 64kHz

MANUAL: Individual menu options are manually

adjusted.

AUTO:

Every menu option is automatically
adjusted.

Notes:
- Press the   button to select [AUTO].
- To choose a menu option: SELECT button
- To go to the next menu:

MENU button

CLOCK
The figure below demonstrates how to adjust so

that vertical flicker noise is not emitted. (  
buttons)

PHASE
The figure below demonstrates how to adjust so

that horizontal flicker noise is not emitted. (  
buttons)
Note:
- Adjustments to PHASE should be made only

after CLOCK has been correctly set.

H-POS (horizontal positioning) and V-POS
(vertical positioning)
To center the screen image within the boundaries
of the screen, adjust the left-right (H-POS) values

and the up-down (V-POS) values. (    buttons)

Vertical flicker noise

Horizontal flicker noise

Screen frame

GAIN CONTROL

MANUAL

AUTO

BLACK LEVEL
CONTRAST

51
65

INPUT-1

ANALOG

1280 x 1024

V : 60Hz

H : 64kHz

MANUAL: Individual menu options are manually

adjusted.

AUTO:

Every menu option is automatically
adjusted using the Auto Gain Control*
function.

Notes:
- Press the   button to select [AUTO].
- To choose a menu option: SELECT button
- To go to the next menu:

MENU button

* Auto Gain Control function
- The Auto Gain Control adjusts contrast and black

level based on the brightest color of the image
displayed. Unless an Adjustment Pattern is used,
automatic adjustment may not be possible. In
such a case, either use an Adjustment Pattern,
or adjust manually.

- If the signal coming from the computer is

composite sync or sync on green, automatic
adjustment cannot be performed. Please perform
manual adjustment instead.

BLACK LEVEL
Total screen brightness can be adjusted while

watching the color pattern. (    buttons)

CONTRAST
While watching the color pattern, adjustments can
be made so that all graduations appear.
(    buttons)

Color pattern

COLOR CONTROL

sRGB

STD

VIVID

COLOR MODE
WHITE BALANCE
HUE
SATURATION

0
0

INPUT-1

ANALOG

1280 x 1024

V : 60Hz

H : 64kHz

Notes:
- To choose a menu option: SELECT button
- To go to the next menu:

MENU button

COLOR MODE
Color tone can be set as below.

sRGB : sRGB is international standard of color

representation specified by IEC
(International Electrotechnical Commis-
sion). Color conversion is made in
taking account of liquid crystal’s
characteristics and represents color
tone close to it original image.

STD :

Displays image with the color tone
results from original scheme of liquid
crystal panel.

VIVID : Displays an image with dynamic and

VIVID primary colors.

- If [sRGB] or [VIVID] has been selected, items

subsequent to [WHITE BALANCE] cannot be set.

Subsequent items can be set when the [COLOR
MODE] is [STD].

WHITE BALANCE
After selecting [WHITE BALANCE], press the 
button and display the adjustment menu.

WHITE BALANCE

R-CONTRAST
G-CONTRAST
B-CONTRAST

COOL

WARM

USER

STD

OK    

<

 MENU 

>

Notes:
- On settings other than [STD] not all graduations

can be displayed. To display all graduations, set
to [STD].

- Use the     buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting USER will display the setting values for

[R-CONTRAST], [G-CONTRAST] and [B-
CONTRAST], in order to make fine adjustments.

- Use the SELECT button to select

[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST].

- When adjustment complete: MENU button