DOWNLOAD Sharp LL-191A (serv.man3) Service Manual ↓ Size: 773.97 KB | Pages: 30 in PDF or view online for FREE

About the ColorSync profile
ColorSync is Apple Computer's color management
system and enables color reproduction
characteristics to be realized when used with a
compatible application. A ColorSync profile
describes the color characteristics of the LCD
monitor.

Notes:
- This monitor's ColorSync profile works with

MacOS 8.5 or above.

- When using the ColorSync profile, set as

follows:
- [DISPLAY MODE]: [STD] or [OFFICE]
- [WHITE BALANCE]: [STD]
- [GAMMA]: [0]

Notes:
- It is necessary to have PC Exchange or File

Exchange installed in your system.

- Depending on the type of computer or OS,

command names and methods may differ.
Please follow the computer's own operation
manual while reading this.

1. Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2. Copy the profile to be used from the CD-ROM to

the ColorSync profile folder in the system folder.

3. Using the ColorSync on the control panel,

choose the profile to be used.

191A_gb.P65

12/15/2003, 5:27 PM

29

The following stand or arm can be attached to the
monitor.
- Stand (sold separately)

Model name: NL-S02

-H (Ivory)

NL-S02-B (Black)

- VESA-compatible arm (commercially available)

Attachments must satisfy the following.
- Compatible with the VESA standard.
- Have a gap of 100 mm x 100 mm between the

screw holes on the section to be attached.

- Not be likely to fall off or break off after being

attached to the monitor.

- Be careful not to over bend the cable or add

extension cords as this could lead to malfunction.

- While following these instructions, please also

refer to the installation instructions in the
operation manual included with the arm or stand.

- Be careful not to get your fingers pinched

between the display and stand nor to let the
stand drop. These could lead to injury.

1. Remove the cables.
2. Spread out a soft cloth on a suitable horizontal

surface.

3. Being careful not to damage the monitor, gently

lay the monitor on it display-side down.

4. Remove the four screws and then remove the

stand from the monitor.

Notes:
- The stand is specially made for use with this

monitor. Once having removed the stand, never
attempt to attach it to another device.

- Once having removed the screws, store them

together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to a malfunction.

5. Attach the arm to the monitor with the four screws.

Note:
- The screws used to attach the arm should be M4

screws with a length of 6 - 8 mm protruding from
the surface to be attached. Using different
screws could cause the monitor to fall off or to be
internally damaged.

Screw used to attach arm

Arm
Part of monitor to which arm is
attached

03_191A_gb.P65

12/19/2003, 2:29 PM

30

The following stand or arm can be attached to the
monitor.
- Stand (sold separately)

Model name: NL-S02

-H (Ivory)

NL-S02-B (Black)

- VESA-compatible arm (commercially available)

Attachments must satisfy the following.
- Compatible with the VESA standard.
- Have a gap of 100 mm x 100 mm between the

screw holes on the section to be attached.

- Not be likely to fall off or break off after being

attached to the monitor.

- Be careful not to over bend the cable or add

extension cords as this could lead to malfunction.

- While following these instructions, please also

refer to the installation instructions in the
operation manual included with the arm or stand.

- Be careful not to get your fingers pinched

between the display and stand nor to let the
stand drop. These could lead to injury.

1. Remove the cables.
2. Spread out a soft cloth on a suitable horizontal

surface.

3. Being careful not to damage the monitor, gently

lay the monitor on it display-side down.

4. Remove the four screws and then remove the

stand from the monitor.

Notes:
- The stand is specially made for use with this

monitor. Once having removed the stand, never
attempt to attach it to another device.

- Once having removed the screws, store them

together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to a malfunction.

5. Attach the arm to the monitor with the four screws.

Note:
- The screws used to attach the arm should be M4

screws with a length of 6 - 8 mm protruding from
the surface to be attached. Using different
screws could cause the monitor to fall off or to be
internally damaged.

Screw used to attach arm

Arm
Part of monitor to which arm is
attached

03_191A_gb.P65

12/19/2003, 2:29 PM

30

The following stand or arm can be attached to the
monitor.
- Stand (sold separately)

Model name: NL-S02

-H (Ivory)

NL-S02-B (Black)

- VESA-compatible arm (commercially available)

Attachments must satisfy the following.
- Compatible with the VESA standard.
- Have a gap of 100 mm x 100 mm between the

screw holes on the section to be attached.

- Not be likely to fall off or break off after being

attached to the monitor.

- Be careful not to over bend the cable or add

extension cords as this could lead to malfunction.

- While following these instructions, please also

refer to the installation instructions in the
operation manual included with the arm or stand.

- Be careful not to get your fingers pinched

between the display and stand nor to let the
stand drop. These could lead to injury.

1. Remove the cables.
2. Spread out a soft cloth on a suitable horizontal

surface.

3. Being careful not to damage the monitor, gently

lay the monitor on it display-side down.

4. Remove the four screws and then remove the

stand from the monitor.

Notes:
- The stand is specially made for use with this

monitor. Once having removed the stand, never
attempt to attach it to another device.

- Once having removed the screws, store them

together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to a malfunction.

5. Attach the arm to the monitor with the four screws.

Note:
- The screws used to attach the arm should be M4

screws with a length of 6 - 8 mm protruding from
the surface to be attached. Using different
screws could cause the monitor to fall off or to be
internally damaged.

Screw used to attach arm

Arm
Part of monitor to which arm is
attached

03_191A_gb.P65

12/19/2003, 2:29 PM

30