Sharp LL-191A (serv.man3) User Manual / Operation Manual ▷ View online
13
English
CAUTION!
- When connecting, ensure that both the monitor
and computer are switched off.
- Be careful not to over bend the cable or add
extension cords as this could lead to a
malfunction.
malfunction.
Connecting the monitor to a computer
Connect the accessory analog signal cable to the
analog RGB output terminal of the computer.
analog RGB output terminal of the computer.
- Paying attention to connector direction, firmly
insert the signal cable vertically into the
connector, and then tighten the screws at both
sides.
connector, and then tighten the screws at both
sides.
If connecting to a D-sub15 pin 2 row Apple Power
Macintosh, attach a Macintosh conversion adapter
(commercially available) to the analog signal
cable.
Macintosh, attach a Macintosh conversion adapter
(commercially available) to the analog signal
cable.
Note:
- If connecting to the Sun Ultra series, a
- If connecting to the Sun Ultra series, a
conversion adapter (commercially available)
may be required.
may be required.
Connecting the monitor and turning the monitor on and off
Analog signal cable
Analog RGB terminal
(Mini D-sub 15 pin, 3 row)
(Mini D-sub 15 pin, 3 row)
Analog RGB terminal
(Mini D-sub 15 pin, 3 row)
(Mini D-sub 15 pin, 3 row)
Macintosh conversion adapter
Connect the accessory audio cable
When the accessory audio cable is connected to
the audio output terminal of the computer, the
sound of the connected computer is output from
the monitor speakers. You can also use the
headphone jack of the display.
the audio output terminal of the computer, the
sound of the connected computer is output from
the monitor speakers. You can also use the
headphone jack of the display.
Audio output terminal
Audio cable
Audio input terminal
191A_gb.P65
12/15/2003, 5:27 PM
13
14
Connection of headphones
(commercially available)
(commercially available)
Headphones (commercially available) can be
connected.
connected.
Notes:
- When the headphones are connected, no sound
- When the headphones are connected, no sound
can be heard from the monitor speakers.
- Use headphones with a cable less than 3 m in
length.
Connecting the monitor to a power
source
source
Connecting the monitor and turning the monitor on and off
Turning the power on
1. Turn on the main power of the monitor.
- When switching the main power switch on and
off, always wait for an interval of at least 5
seconds. Rapid switching may result in
malfunction.
seconds. Rapid switching may result in
malfunction.
2. Press the monitor's power button.
3. Turn on the computer.
3. Turn on the computer.
When a signal is input from the computer, the
power LED lights up green, and the screen is
displayed. (After power is turned on, it may take
a little time until the screen is displayed.)
power LED lights up green, and the screen is
displayed. (After power is turned on, it may take
a little time until the screen is displayed.)
Notes:
- If using the monitor for the first time or after
- If using the monitor for the first time or after
having changed the system settings during use,
perform an automatic screen adjustment. (p.18)
perform an automatic screen adjustment. (p.18)
- Depending on the type of computer or OS, you
may need to install the monitor set-up
information on your system. (p.26)
information on your system. (p.26)
- When connecting to a notebook, if the notebook
computer's screen is set to display at the same
time, the MS-DOS screen may not display
properly. In this case, change the setting to
display only the LCD monitor.
time, the MS-DOS screen may not display
properly. In this case, change the setting to
display only the LCD monitor.
Turn on the
computer power
supply.
computer power
supply.
ON
Headphones
Headphone terminal
AC outlet
Power cord
Power terminal
Main power switch
Press power button.
191A_gb.P65
12/15/2003, 5:27 PM
14
15
English
Connecting the monitor and turning the monitor on and off
Turning the power off
1. Turn the computer off.
2. Press the monitor's power button.
2. Press the monitor's power button.
The power LED will disappear.
If the monitor will not be used for a long time, turn
off the main power switch of the monitor, and
remove the power plug from the outlet.
off the main power switch of the monitor, and
remove the power plug from the outlet.
OFF
Turn the computer
off.
off.
Press power button.
191A_gb.P65
12/15/2003, 5:27 PM
15
16
Adjusting the screen display and speaker volume
Adjustment lock function
By disabling the control buttons (i.e. setting the
lock) any attempted changes to adjusted values
will be voided.
1. Turn off the monitor power.
2. While pressing the MENU button, press the
lock) any attempted changes to adjusted values
will be voided.
1. Turn off the monitor power.
2. While pressing the MENU button, press the
power button (i.e. turn the power on).
Continue to press the buttons until
[ADJUSTMENT LOCKED] appears on the screen.
The lock is set when the message is displayed.
Continue to press the buttons until
[ADJUSTMENT LOCKED] appears on the screen.
The lock is set when the message is displayed.
Note:
- When the lock is in place, all buttons other than
- When the lock is in place, all buttons other than
the power button are disabled.
Adjustment lock release
1. Turn off the monitor power.
2. While pressing the MENU button, press the
1. Turn off the monitor power.
2. While pressing the MENU button, press the
power button (i.e. turn the power on).
Continue to press the buttons until [ADJUSTMENT
UNLOCKED] appears on the screen. The lock is
released when the message is displayed.
Continue to press the buttons until [ADJUSTMENT
UNLOCKED] appears on the screen. The lock is
released when the message is displayed.
Adjusting the backlight
1. Without the OSD Menu being displayed, press
the or the button.
2. Check that [BRIGHT] is selected.
If it is not selected, press the
/ MODE button
and select [BRIGHT].
3. Adjust by pressing the button (darker) or
button (lighter).
Note:
- On Screen display for adjustment disappears
- On Screen display for adjustment disappears
several seconds after the last operation.
Note:
- All adjustments will be saved even after turning
- All adjustments will be saved even after turning
the power off.
Resetting all adjustment values
All adjustment values can be returned to their
original ex-factory values in one command.
1. Turn off the monitor power.
2. Press the MENU button and the
original ex-factory values in one command.
1. Turn off the monitor power.
2. Press the MENU button and the
/ MODE
button simultaneously, and while doing this
press the power button (i.e. turn the power on).
Continue to press the buttons until [ALL RESET]
appears on the screen. Reset is complete when
the displayed message disappears.
press the power button (i.e. turn the power on).
Continue to press the buttons until [ALL RESET]
appears on the screen. Reset is complete when
the displayed message disappears.
Notes:
- While [ALL RESET] is displayed, the control
- While [ALL RESET] is displayed, the control
buttons are disabled.
- It is not possible to reset values when the
adjustment lock is in place. Remove the
adjustment lock before attempting to operate
control buttons.
adjustment lock before attempting to operate
control buttons.
ADJUSTMENT Menu reset
Settings of items in the ADJUSTMENT Menu
(CLOCK, PHASE, H-POS, V-POS) can be returned
to their original ex-factory values.
1. Turn on the monitor power.
(CLOCK, PHASE, H-POS, V-POS) can be returned
to their original ex-factory values.
1. Turn on the monitor power.
2. Press the MENU button and the button
simultaneously. When [RESET] appears on the
screen, the reset is complete.
screen, the reset is complete.
Notes:
- While [RESET] is displayed, the control buttons
- While [RESET] is displayed, the control buttons
are disabled.
- It is not possible to reset values when the
adjustment lock is in place. Remove the
adjustment lock before attempting to operate
control buttons.
adjustment lock before attempting to operate
control buttons.
191A_gb.P65
12/15/2003, 5:27 PM
16
Click on the first or last page to see other LL-191A (serv.man3) service manuals if exist.