DOWNLOAD Sharp R-61FBSTM (serv.man2) Service Manual ↓ Size: 771 KB | Pages: 49 in PDF or view online for FREE

3

The appropriate indicator will flash or light up,
just above each symbol according to the
instruction. When an indicator is flashing,
press the required button (having the same
symbol) or do the necessary operation.

Stir

Turn over

Weight

Grill

Microwave power level

Cook 

R-61+62FBSTM Operation Manual  24/07/2003  10:27  Page 3

4

• Remove all packing materials including the

feature sticker (if present). Do not remove the
plastic film from the inside of the oven window
as this protects it from dirt. The waveguide
cover prevents food and grease from entering
the waveguide area where it
could cause damage.
DO NOT REMOVE THE
WAVEGUIDE COVER.

• Make sure the power supply

cord is undamaged (See “ELECTRICAL
CONNECTION” on the following page).
Do not allow the power supply cord to
run over any hot or sharp surfaces, such
as the hot air vent area at the top rear of
the oven.

• The socket must be readily accessible so that it

can be easily unplugged in an emergency.

• Do not use the oven outdoors.

Oven Use:
• The oven is for domestic use only.
• Never operate when empty, except as directed

in the ‘Grill cooking’ section on page 12.

• Do not leave or store anything inside the oven

when not in use.

• Never attempt to use the oven with the door

open. It is important not to force or tamper
with the door safety latches.

• Never operate the oven with any object caught

in the door.

• Do not insert fingers or objects in the holes of

the door latch openings as this may damage
the oven and cause an electric shock.

• The door, front trim, oven cavity, turntable,

dishes, accessories and especially the grill will
become very hot during operation. Care
should be taken to avoid touching these areas.
To prevent burns, always use thick oven gloves.
Before cleaning make sure they are not hot.

Pacemaker: If you have a heart pacemaker,
consult your doctor or the pacemaker
manufacturer prior to oven use.

R-61+62FBSTM Operation Manual  24/07/2003  10:27  Page 4

5

1. Remove all packaging and check carefully for

any signs of damage.

2. Fit the appliance into the kitchen cupboard

slowly, and without force, until the front
frame of the oven seals against the front
opening of the cupboard.

3. Ensure the appliance

is stable and not
leaning.  Ensure that a
5mm gap is kept
between the
cupboard door above
and the top of the
frame (see diagram).

4. Fix the oven in position with

the screws provided.
The fixing points are located
on the top and bottom
corners of the oven (see
diagram, item 11, on page 2).

5. It is important to ensure that the installation

of this product conforms to the instructions in
this operation manual and the hob
manufacturer’s installation instructions.
If you require assistance concerning the
installation of the appliance, please contact
your nearest authorized Sharp service agent,
see page 27 for details.

5 mm

• This appliance has been tested and approved for use near domestic gas, electric and induction

hobs only.

• Sufficient space between hob and microwave should be allowed to prevent overheating of

microwave oven, surrounding cupboard and accessories.

• Do not operate the hob without pans

when the microwave oven is operating.

• The cupboard must be a minimum of

500 mm (A) above the worktop and
must not be installed directly above a
hob or other kitchen appliance e.g.
conventional oven or refrigerator.

• Care should be taken when attending

to the microwave oven while the hob
is on.

• The front of the oven can be cleaned

with mild soap and water.
Do not use commercial oven cleaners,
abrasive harsh cleaners, or those that
contain Sodium Hydroxide.

A

A

R-61+62FBSTM Operation Manual  24/07/2003  10:27  Page 5

6

• The fuse from the cut-off plug should be

removed and the plug disposed of in a safe
manner.

• Under no circumstances should the cut-off

plug be inserted into a socket outlet as a
serious electric shock may occur.

• The plug must not be used without the fuse

cover fitted.

• If you have any doubt about your microwave

oven obtain the help of a qualified electrician.

• When replacing the plug please ensure that

you use a BSI or ASTA approved plug to
BS1363, this should be fitted with a brown
coloured 13 amp fuse approved by BSI or
ASTA to BS1362. If you have any doubt about
electrical connection seek the help of a
qualified electrician. 

To wire an appropriate plug, follow the wiring
code given in `To replace the mains plug’ on
page 27.

• Do not allow water to come into contact with

the power supply cord or plug.

• Insert the plug properly into the socket.
• Do not connect other appliances to the same

socket using an adaptor plug.

• If the power supply cord is damaged, it must

be replaced by a SHARP approved service
facility or a similarly qualified person to avoid a
hazard. 

• When removing the plug from the socket

always grip the plug, never the cord as this may
damage the power supply cord and the
connections inside the plug.

• If the plug fitted to your oven is a rewireable

type and in the event of the socket outlet in
your home not being compatible with the plug
supplied, remove the plug properly (do not cut
off). 

• If the plug fitted to your oven is a non-

rewirable type and in the event of the socket
outlet in your home not being compatible with
the plug supplied, cut-off the mains plug.

• Refit with a suitable type, observing the wiring

code given in `To replace the mains plug’ on
page 27.

• The electrical outlet should be readily accessible so

• The socket should not be postioned behind the

• The best position is above the cupboard, see (A).

When not connecting the power supply cord to position (A) it
should be removed from the support clips (see diagram, item
14, on page 2) and routed under the oven. 

• Connect the appliance a single phase 230-240V/50Hz

alternating current via a correctly installed earth socket.
The socket must be fused with a 

≥16A fuse.

• If the appliance is to be operated in a non-European

• The power supply cord may only be replaced by an electrician.
• Before installing, tie a piece of string to the power supply cord to facilitate connection to point (A)

when the appliance is being installed.

• When inserting the appliance into the high-sided cupboard, DO NOT crush the power supply cord.

R-61+62FBSTM Operation Manual  24/07/2003  10:27  Page 6