DOWNLOAD Sharp VENTA (serv.man11) Service Manual ↓ Size: 163.9 KB | Pages: 89 in PDF or view online for FREE

36

REM ************************WINTI SETTING END***************************

1.

Remove the # on this line to allow WINTi - Compulsory

2.

Remove the # on this line to set the PC Path FOR WINTi - Compulsory

3.

EFTEOD= This line is not compulsory. If set as EOD no change in operation

will be experienced. If however it is set as C:\WINTICMD.TXT it could invoke

an End of Day on WINTi. The setting invokes a preset script at WINTi which

can also invoke communication to the bank. To realise this function please
contact Sharp UK - Not Compulsory

4.

EFTNOCHK=1 This line will allow the POS when in Manual Key entry mode
only to prompt for relevant information. i.e Start Date, End Date Issue

Number. If the Card type does not need Start Date it will not be prompted

for. Care should be taken as if the set sequence is changed it may cause
problems of consistency with operators. N.B if the line is active the

feature is DISABLED - Not Compulsory

5.

EFTMAXCHAN=10 This line sets the number of active channels per POS. It

should be left at 10 unless for specific reasons. The DOS version allowed 16

per system, so this at 10 should be more than enough. - Compulsory

6.

EFTACC=001 This setting is not used, the Account will be set to 001 as

default if this line is not removed. Use only on multi account sites. - Not

Compulsory

7.

EFTOCCPATH=nnnnn This line defaults to a sub setting of EFTREQ if it is

changed for any reason it should be the same as EFTREQ with \POS. - Not
Compulsory

8.

EFTCASHBACK=n,m - This line allows Cashback on the POS terminal. See

item 24

9.

EFTGRATUITY=1 - Allows Gratuity print on the Voucher

10.

Pmn=CNP This line allows entry of EFT transactions with the “Customer NOT

Present”. This should only be set with agreement from the Bank or Acquirer.
It sets the payment method to send the transaction as a Customer NOT

Present. N is the Payment Method Number - Not Compulsory

37

The operation has been left unchanged to allow easy conversion for customers. The

same functionality of Suspend etc are included as in the DOS Version. The only

differences that will be seen are 1. during Manually Keyed Transaction as in 4 above
or if 2. a customer NOT present Transaction is made or 3. The operator wishes to

force a transaction on-line over ruling the floor limit.

38

As it is possible when using the Waitermate Hand-Held Terminal that items sold at

the “Waitermate” POS terminal do not need to print at a Dispense Printer located at

the POS terminal, a new KP suppression feature has been introduced.

A POS terminal with two KP’s connected one for kitchen items and the

other for Bar dispense has a Waitermate Homebase connected. It is
necessary that items selected on the Waitermate need to print at the

kitchen and also at the Bar dispense, however items selected directly

from the POS terminal need only print in the kitchen.

In order to realise this function a new setting has been introduced in S2001.INI, as
follows

REM V4********************WAITERMATE PROGRAMMING START******************

REM ============PORT SETTING============

REM To set the Port that the Waitermate Base Station is connected to

REM remove the # below and set n= Com Port Number

# WAITERMATE=n

REM ======WAITERMATE PRINT STATION======

REM To set which POS Terminal to send Waitermate Reciepts and Bills
REM remove the # below and set n= POS Terminal Number and
REM x= to the Waitermate Number (e.g To set Waitermate 1 to print at POS
REM Terminal 3 WMPRINT1=3)

# WMPRINTx=n

REM ======KP LOCAL SUPPRESSION=========

REM IN ORDER TO STOP DISPENSE PRINTING AT A LOCAL NODE WHEN USING THE
REM WAITERMATE SET KPSUPPRESS=n,n,n WHERE n IS THE KP NUMBER

REM *********************WAITERMATE PROGRAMMING END*********************

KPSUPPRESS=n,n – This setting suspends the use of the Dispense Printer at
the local machine, if more than one printer is required to be suppressed it is

possible to set multiple printers (i.e KPSUPPRESS=1,4 WILL SUPRESS KP1 &

4).

39

To realise table entry by Magnetic Card Swipe the Swipe for Table entry feature has

been introduced. The function allows new table opening and table addition to be

performed.

To realise this function new settings are available in S2001.INI

REM V4.4***************MAGNETIC CARD FOR TABLE SET**********************

REM TO ALLOW THE OPENING OF A TABLE USING A MAGNETIC CARD
REM REMOVE THE REM STATEMENT BELOW

REM WHERE x=CARD START NUMBER AND y=NO OF DIGITS FOR TABLE NUMBER
REM EXAMPLE CARD NUMBER 12345001 WOULD SET AS 12345%3

REM TO SET AUTOMATIC COVERS REMOVE REM BELOW AND SET n=DEFAULT COVER COUNT
# SWIPECOVERS=1...................................................2

REM *******************MAGNETIC CARD FOR TABLE END**********************

Two settings are available :-

1.

TABLESWIPE=x%y - This setting selects the format of the card, this gives

great flexibility on the card types used. If the card chosen has a number

87347001 for room 1 and 87347003 for room 3 then the starting digits of

87347 are consistent for the site it is only the last 3 digits that contain the
room number. The setting for table swipe would therefore be:-

TABLESWIPE=87347%3

2.

SWIPECOVERS=1 - When a table is entered the No of Covers are asked for.

This could be inconvenient in operation and the customer may not be
interested in Cover count. To by-pass this function remove the REM in front of

SWIPECOVERS and add the number of covers that are required on table

entry. The default is 1.

The function can be used after clerk entry. If the card is swiped it will be opened
with the default no of covers if SWIPECOVERS is set and re-ordering will take place

if the card is swiped after clerk entry later. If SWIPECOVERS are not set then the

POS will prompt for the number of covers.