DOWNLOAD Sharp UP-3300 (serv.man17) Service Manual ↓ Size: 852.32 KB | Pages: 14 in PDF or view online for FREE

1) Remove the LCD unit 

1

.

a) Remove the four Screws 

2

.

2) Remove the LCD rear cabinet 

3

.

a) Remove the two Screws 

4

.

b) Remove the pawls 

a

 to 

1

 of the LCD rear cabinet 

3

 in that

order.

3) Remove the Inverter PWB 

5

.

a) Remove the Inverter cable 

6

.

b) Remove the CCFT cable 

7

.

c) Remove the two screws 

8

.

d) Remove the Inverter cover 

9

.

4) Remove the Touch panel PWB unit 

F

.

a) Remove the LCD cable(40P) 

G

.

b) Remove the LCD cable(30P) 

H

.

c) Remove the Inverter cable 

I

.

d) Remove the two Screws 

J

 and the two Earth wire 

K

.

e) Remove the Screw 

L

.

1

2

2

– 4 –

5) Remove the LCD 

M

.

a) Remove the five Screws 

N

.

b) Remove the LCD plate 

O

.

c) Remove the LCD PWB unit 

P

.

Install the LCD unit in the reverse order of removing.

Before installing, make sure that each cables are connected securely.

1) Remove the top cabinet.

2) Install the Expansion RAM Board 

1

 to the Option RAM connector

on the Main PWB.

a) Insert the Expansion RAM Board aslant into the option RAM

connector.

b) Push the RAM disk unit Expansion RAM Board is locked by

the arms of option RAM connector.

*

It is possible to install one UP-P02MB2.

*

Be careful of the direction of Expansion RAM Board to be
installed. Install the Expansion RAM Board with the notch
part of the PWB (Figure A) come right. Installing the Expan-
sion RAM Board in the wrong direction may damage the
connector part or make the machine out of order.

3) Removing the Expansion RAM Board.

a) Open the arms of option RAM connector right and left.

b) The Expansion RAM Board will be lifted automatically.

1) Remove the rear cover.

2) Remove the rear display.

2) Remove the two screws 

1

 from the shassis.

3) Insert the I/F PWB 

2

 to the connector.

4) Fix the I/F BRACKET to the shassis with screws 

1

.

5) Install the ferrite Core 

3

.

6) Install the Nylon band 

4

 to the cables.

17

20

18

19

Touch panel

18

18

18

1

A

– 5 –

1) Fix the MCR ANGLE 

1

 to the lower cabinet with two screws 

2

.

2) Connect the MCR cable 

3

 to the MCR connector with the cable

holder  

6

, and tighter the screw 

7

 on the back of lower cabinet.

3) Install the ferrite Core 

4

 to the MCR cable.

4) Install the Nylon band 

8

 to the cable.

5) Fix the earth wire 

5

 from the UP-E12MR2 with the screw.

1) Connect the drawer cable 

1

 to the drawer connector 

2

.

2) Fix the earth wire 

3

 from drawer box unit with the screw 

4

.

3) Install the ferrite Core 

5

 to the drawer cable.

4) Fix the drawer cable 

1

 with the cable holder 

6

, and tighten the

screw 

7

 on the back of lower cabinet 

A

 or 

B

.

When the remote display is installed, service resetting is required.

1) Connect to the Display cable 

1

 to the display connector 

2

.

2) Fix the earth wire 

3

 from the display unit with screw 

4

.

The pole can be extended by installing the attached pole to the
standard pole.

No.

NAME

USE

Q’ty

G

Pole cabinet

Pole extension

2

H

Screw (M2 

×

 8)

Pole connection

4

I

Screw (M4 

×

 16)

Securing the UP-P16DP to
the wooden table

4

J

Screw (M4 

×

 20)

Securing the UP-P16DP to
the metal table

4

K

Nut

Securing the UP-P16DP to
the metal table

4

1) Remove the five screws 

1

.

2) Remove the Base angle 

2

.

1

2

3

4

1

1

2

– 6 –

  3) Remove the two screws 

6

.

  4) Remove the Base cabinet 

4

 from the pole cabinet 

7

.

 5) Turn the ratchet 

9

 connected to the pole cabinet 

7

 to the

removing position and pull it out from the display unit 

8

 as

shown in Fig. A.

  6) Remove the two screws 

F

.

  7) Remove the pole cabinet 

7

 from the Ratchet 

9

.

  8) Install the attached pole cabinet 

G

 to the pole cabinet 

7

 to fix it

with the screw 

H

.

 9) Install the pole cabinet 

G

 in the opposite order of the disas-

sembly.

10) Fastening onthe table:

Secure the Base cabinet 

2

 using the screw.

No.

NAME

USE

Q’ty

I

Screw (M4 

×

 16)

Securing the UP-P16DP to
the wooden table

4

J

Screw (M4 

×

 20)

Securing the UP-P16DP to
the metal table

4

K

Nut

Securing the UP-P16DP to
the metal table

4

7

4

6

8

10

7

10

9

9

Fig. A

Display cable

7

7

11

11

12

12

13

13

14

14

15

15

– 7 –