DOWNLOAD Sharp UP-3300 (serv.man16) Service Manual ↓ Size: 4.75 MB | Pages: 108 in PDF or view online for FREE

Initial coordinates (xi, yi) 

↔

 Touch panel coordinates (xt, yt) conver-

sion

xt = (xi - 4096*x1/x)*(x / (x2-x1))
yt = (yi - 4096*y1/y)*(y / (y2-y1))

Touch panel coordinates (xt, yt) 

↔

 VGA coordinates (xv, yv) conver-

sion

xv = xt * 640 / 4096
yv = yt * 480 / 4096

•

Coordinates of correction points

Initial coordinates

393, 402

2080, 402

3767, 402

393, 2048

2080, 2048

3767, 2048

393, 3697

2080, 3697

3767, 3697

Touch panel coordinates

100, 100

2048, 100

3996, 100

100, 2048

2048, 2048

3996, 2048

100, 3996

2048, 3996

3996, 3996

VGA coordinates

16, 14

320, 14

624, 14

16, 240

320, 240

624, 240

16, 465

320, 465

624, 465

The application software of the UP-3300 written in the flash ROM.

In the following cases, writing procedure of the application software
into the flash ROM is required

•

When the flash ROM is replaced with new one. The service part
flash ROM does not include the application software in it.

•

When IPL writing is required because of change in the software.

*

The service part ofthe main PWB unit includes the flash ROM with
the application software written in it, and there is no need for
writing the application software when replacing the main PWB unit.

There are two ways of IPL procedures.

•

IPL from P-ROM via ER-A7RS

•

IPL from PC via IR ( infrared ) communication (Please refer the
next section)

The detailed descriptions on the above procedures are given below.

(1) Install the two master ROMs to the IC socket (IC12 , IC13) on the

ER-A7RS.

Master ROM -1 : VHI27801RAFxx
Master ROM -2 : VHI27801RAGxx

(2) IPL sitch on the ER-A7RS : Set the IPL SW to ON position.

(3) Install the ER-A7RS to the UP-3300. (The UP-3300 power should

be turned OFF.)

(4) Turned on the power of the UP-3300.

(5) The buzzer sounds intermittently during the running of IPL and the

program finishes after the buzzer gives five beeps at short inter-
vals.

(6) Turn OFF the power of the UP-3300.

(7) Remove the ER-A7RS from the UP-3300.

(8) Perform the Master reset . 

This specification covers the utility program "UTL33.EXE" for UP-
3300 series. The "UTL33.EXE" is a program which runs on the PC
DOS prompt screen, it is connected to the UP-3300 through IR. It has
the following functions: (1) UP-3300 IPL operation; (2) LOGO data
rewrite for built-in printer UP- T80BP; and (3) program rewrite.

PC and UP-3300 are connected through IR.

Fig 1. Connection between PC and UP-3300

The following three functions become available:

(1) UP-3300 program rewrite (IPL)

The UP-3300 program is updated. S-type files or ER01FD type
data files are used for ROM data.

(2) LOGO data rewrite

The LOGO STAMP data for the UP-T80BP is set.

Black-and-white BMP/PCX data is used and the image size is up
to 576x240 dots.

(3) Program rewrite (IPL)

The UP-T80BP program is updated. S-type files are used for ROM
data.

According to the contents of the file, "UTL33.EXE" automatically
selects the appropriate protocol from the three types described
above. 1

IPL  SW

OFF

ON

IC13 ROM2 

IC12 ROM1 

MASTER
P-ROM -1

MASTER
P-ROM -2

RS-232C

CE-IR4

PC
without IR

UP-3300

PC with IR

UP-3300

1. PC + CE-IR4 system

2. PC only system

3 – 3

No

Procedure on P.C. side

No

Procedure on UP-3300 side

1

Install "UTL33.EXE" on the P.C.

2

Turn OFF the power.

3

Select "IPL Mode".
Set "IPL Switch" of UP-3300 to "ON".

4

Turn ON the power.

5

Starting of "IPL Mode".
UP-3300 shows
          "IPL from IR"

6

Connect P.C. and UP-3300 via IR. (Fig 1)

7

Execute "UTL33.EXE" on P.C.
 Operation:
          >UTL33 3300_1.ROM 3300_2.ROM
("3300_1.ROM" and "3300_2.ROM" are file name of S-type
ROM object.)

8

Program data is sent to UP-3300 automatically.

8

Program data is received from P.C. automatically.
UP-3300 shows

9

"UTL33.EXE" is completed.
P.C. shows
     "Completed."

9

UP-3300 shows
     "Completed."

10

Turn OFF the power.

11

Select "Normal Mode".
  Set "IPL switch" to "OFF".

12

Execute "Service Reset" on UP-3300.

IPL SW

ON

IR Filter

IPL from IR

IPL from IR
Connected IRDA 115200
21 22 23 24 25 26 27 28

IPL from IR
Connected IRDA 115200
21 22 23 24 25 26 27 28
29 2A 2B 2C 2D 2E 2F
Completed.

IPL from IR
Connected IRDA 115200
30 31 32 33 34 35 36 37
38 39 3A 3B 3C 3D 3E 3F
Completed.

3 – 4

No

Procedure on P.C. side 

No

Procedure on UP-3300 side

1

Install "UTL33.EXE" on the P.C.

2

Enter the SRV mode. Then turn OFF the power or UP-3300.

3

While pressing the On-Line key, tum ON the power of UP-3300.
Keep pressing the On-Line key, and then press the Feed key
also. (Don’t move a finger from the On-line key.)

4

UP-T80BP enters into LOGO mode.
UP-T80BP prints out 
      "

****************

".

5

Go into "UP-T80BP Utility mode".
  Select "6 UP-T80BP Utility" in SRV mode.

6

Starting of "UP-T80BP Utility mode".
UP-3300 shows

7

Connect P.C. and UP-3300 via IR. (Fig 1)

8

Execute "UTL33.EXE" on P.C.
 Operation:
          >UTL33 LOGO.BMP
("LOGO.BMP" is a file name of Bit-Map image.)

9

Program data is sent to UP-3300 automatically.

9

Program data is received from P.C. automatically. 

10

"UTL33.EXE" is completed.
P.C. shows
     "Completed." 

 

10

ER-3300 shows
     "Completed." 

And UP-T80BP prints out the LOGO image.

11 

Touch "OK" button.

12 

Touch "EXIT" button.

13

Turn OFF the power of UP-3300.

14

Execute "Master Reset" on UP-T80BP.

No

Procedure on P.C. side

No

Procedure on UP-3300 side

1

Install "UTL33.EXE" on the P.C.

2

Turn OFF the power of UP-3300.

3

Select "IPL Mode" on UP-T80BP.
  Set the Bit 1 of DipSwitch 2 to "ON" to enter "IPL Mode".

4

While pressing both the Feed key and the On-Line key, turn ON
the power of UP-3300.
  The ERROR Lamp and the On-line Lamp of UP-T80BP is
 blinking.

UP-T80BP Utility

EXIT

UP-T80BP Utility

Normal mode

EXIT

UP-T80BP Utility

Normal mode

EXIT

Complete

OK

IPL SW

ON

IR Filter

3 – 5

No

Procedure on P.C. side

No

Procedure on UP-3300 side

5

UP-T80BP enters into IPL mode when the Feed key is pressed.
(UP- T80BP clears the application program which is in its own
flash ROM.)
  The ERROR Lamp is blinking and the On-Line Lamp is
  turned off.

6

UP-T80BP waits the application program data.
  The ERROR Lamp is turned off and the On-Line Lamp is
  turned on.

7

Enter "UP-T80BP Utility" mode.
Select "6 UP-T80BP Utility" in SRV mode

8

Starting of "UP-T80BP Utility" mode.
UP-3300 shows

9

Connect P.C. and UP-3300 via IR. (Fig 1)

10

Execute "UTL33.EXE" on P.C.
 Operation:
          >UTL33 T80BP.ROM
("T80BP.ROM" is a file name of S-type object.)

11

Program data is sent to UP-3300 automatically.

11 

Program data is received from P.C. automatically.

The On-line Lamp of UP-T80BP starts blinking.

12

"UTL33.EXE" is completed.
P.C. shows
     "Completed."

12

ER-3300 shows
     "Completed." 

The On-line Lamp of UP-T80BP stops blinking.

13

Touch  "OK" button.

14

Touch  "EXIT" button.

15

Turn OFF the power of UP-3300.

16

Select "Normal Mode" on UP-T80BP.
  Set the Bit 1 of DipSwitch 2 to "OFF" to enter "Nomal Mode".

17

Execute "Master Reset" on UP-T80BP.

UP-T80BP Utility

EXIT

UP-T80BP Utility

EXIT

IPL mode

IPL mode

UP-T80BP Utility

E X I T

Complete

OK

"UTL33.EXE" is a utility program on P.C. - a program that sends the
application program data of UP-3300, the image data of the Logo
stamp of UP-T80BP or the application program data of UP-T80BP in
order to replace them.

UTL33 [-Fn] [-Cn] filename 

[filename 

...]

filename

Specifies the name file which you want to send.

For UP-3300 IPL

S-type ROM object file

For UP-T80BP LOGO STAMP

BMP/PCX file

For UP-T80BP IPL

S-type ROM object file

-Fn

Specifies the function. Valid values for n are in the range 1
through 3.

1: UP-3300 IPL

2: UP-T80BP LOGO STAMP

3: UP-T80BP IPL

Normally, UTL33.EXE takes the suitable function automatically.
If the automatic selection does not work correctly, please use this
switch.

-Cn

Specifies the number of the serial (COM) port. Valid values for n
are in the range 1 through 2.
The default value is 1 (COM1).

For UP-3300 IPL.

UTL33 3300_1.ROM 3300_2.ROM

For UP-T80BP LOGO STAMP (To use COM2).

UTL33 -C2 LOGO.BMP

For UP-T80BP IPL (To use the switch "-F").

UTL33 -F3 80BP.ROM.

3 – 6