Sharp RZ-X660 (serv.man3) Service Manual ▷ View online
43
In case that there is a problem in the accuracy in using touch screen, please
re-adjust calibration. This is the execution screen of PenMount Control Panel
program.
You can adjust calibration in the
calibrate tab.
User can adjust calibration by selecting
standard calibration and advanced
calibration. User can increase the value
in the advanced mode in order to adjust
position in full detail.
calibrate tab.
User can adjust calibration by selecting
standard calibration and advanced
calibration. User can increase the value
in the advanced mode in order to adjust
position in full detail.
1
User can adjust touch screen and non-
touch screen in the multiple monitors
tab.
touch screen in the multiple monitors
tab.
2
You can set up touch mode and beep
sound in the setting tab and use the
function.
sound in the setting tab and use the
function.
3
Note:
•
Multiple monitors should not be selected in
case of using single monitor, and should be
used when using dual monitor in order to set
up touch screen and non-touch screen.
case of using single monitor, and should be
used when using dual monitor in order to set
up touch screen and non-touch screen.
TOUCH SCREEN SET-UP
44
4
User can set up Draw, Right Button
Icon Enable and Double Click Speed in
the tool tab, and utilize them.
Icon Enable and Double Click Speed in
the tool tab, and utilize them.
You can check the information of
PenMount in the About tab.
PenMount in the About tab.
5
Notice for using touch panel!
•
In case of using touch panel
- Do not touch the panel with sharp instruments such as knife or writing pen
- Please touch the panel with the designated stylus or finger.
- Please polish the touch panel with alcohol and soft cloth only.
- Be careful to prevent alcohol from leaking into the touch panel.
- Do not use other solvent except for alcohol.
- Misuse of the touch panel can damages the product. Damage to the touch screen can
- Please touch the panel with the designated stylus or finger.
- Please polish the touch panel with alcohol and soft cloth only.
- Be careful to prevent alcohol from leaking into the touch panel.
- Do not use other solvent except for alcohol.
- Misuse of the touch panel can damages the product. Damage to the touch screen can
cause errors in registering touch locations accurately.
•
In case of preserving touch panel
- Please keep the product under the standard temperature and humidity.
- Please keep the product in package.
- Do not stack products, and do not place any materials on it.
- Keep the product out of the direct rays of the sun.
- Keep the product away from fire.
- Misuse of product can cause exterior variation.
- Please keep the product in package.
- Do not stack products, and do not place any materials on it.
- Keep the product out of the direct rays of the sun.
- Keep the product away from fire.
- Misuse of product can cause exterior variation.
45
•
In case of assembling touch panel
- Do not use strong force on the touch panel.
- Be careful not to break touch panel, and place it on the soft materials such as sponge.
- Do not pull on touch panel FPC cable or use unnecessary force during assembly.
- If the FPC cable is damaged the touch panel will not register contact in the correct
- Be careful not to break touch panel, and place it on the soft materials such as sponge.
- Do not pull on touch panel FPC cable or use unnecessary force during assembly.
- If the FPC cable is damaged the touch panel will not register contact in the correct
locations.
46
UEFI SETUP UTILITY
Introduction
This section explains how to use the UEFI SETUP UTILITY to configure your system.
The UEFI chip on the motherboard stores the UEFI SETUP UTILITY. You may run
the UEFI SETUP UTILITY when you start up the computer. Please press <F2> or
<Del> during the Power-On-Self-Test (POST) to enter the UEFI SETUP UTILITY,
otherwise, POST will continue with its test routines.
If you wish to enter the UEFI SETUP UTILITY after POST, restart the system by
If you wish to enter the UEFI SETUP UTILITY after POST, restart the system by
pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You may also restart by turning the system off and then back on.
Note:
•
Because the UEFI software is constantly being updated, the following UEFI setup screens and
descriptions are for reference purpose only, and they may not exactly match what you see on
your screen.
descriptions are for reference purpose only, and they may not exactly match what you see on
your screen.
UEFI Menu Bar
The top of the screen has a menu bar with the following selections:
Main
The top of the screen has a menu bar with the following selections:
Main
To set up the system time/date information
Advanced
To set up the advanced UEFI features
H/W Monitor To display current hardware status
Security
To set up the security features
Boot
To set up the default system device to locate and load the
Operating System
Operating System
Exit To exit the current screen or the UEFI SETUP UTILITY
Use < > key or < > key to choose among the selections on the menu bar,
Use < > key or < > key to choose among the selections on the menu bar,
and then press <Enter> to get into the sub screen. You can also use the mouse
to click your required item.
Click on the first or last page to see other RZ-X660 (serv.man3) service manuals if exist.