Sharp UP-800 (serv.man30) User Manual / Operation Manual ▷ View online
7
15.EURO Migration Function·················································································································224
16.Operator Maintenance·······················································································································226
In Case of Power Failure ·····················································································································226
In Case of Printer Error························································································································226
Thermal Printing ··································································································································226
In Case of Printer Error························································································································226
Thermal Printing ··································································································································226
Cautions in handling the printer ··································································································226
Cautions in handling the recording paper (thermal paper) ·························································227
Cautions in handling the recording paper (thermal paper) ·························································227
Installing and Removing the Paper Roll·······························································································228
Recording paper specifications ··································································································228
Installing the paper roll ···············································································································228
Removing the paper roll ·············································································································229
Prevention of paper jams············································································································231
Removing a paper jam ···············································································································232
Installing the paper roll ···············································································································228
Removing the paper roll ·············································································································229
Prevention of paper jams············································································································231
Removing a paper jam ···············································································································232
Cleaning the Print Head·······················································································································233
Removing the Till and the Drawer ·······································································································233
Opening the Drawer by Hand ··············································································································233
Before Calling for Service ····················································································································234
Removing the Till and the Drawer ·······································································································233
Opening the Drawer by Hand ··············································································································233
Before Calling for Service ····················································································································234
17.Options ···············································································································································235
List of Options······································································································································235
18.Specifications ····································································································································236
8
1
Part Names and Functions
This chapter describes the part names and functions of this POS terminal.
External View
■ Front view
■ Rear view
The UP-820F model is available with a drawer
(for the UK) or without a drawer (for Australia
and New Zealand).
(for the UK) or without a drawer (for Australia
and New Zealand).
■ Front view
■ Rear view
(The terminal without drawer)
(The terminal without drawer)
NOTE
Drawer lock
Drawer
SD card slot
Contactless clerk switch
RS232 connector
Power switch
Operator display
Customer display (Pop-up type)
Journal cover
Receipt paper
Keyboard (flat-type)
9
Printer
The POS terminal UP-820F may be configured with multiple types of printers offered by the
market. For specific instructions related to the handling and care of the printer, please refer to
the applicable printer instruction manual.
market. For specific instructions related to the handling and care of the printer, please refer to
the applicable printer instruction manual.
The built-in printer is a 2 station (receipt/journal) type
thermal printer, and therefore it does not require any type
of ink ribbon or cartridge. The average life of the printer is
approximately 5 million lines.
thermal printer, and therefore it does not require any type
of ink ribbon or cartridge. The average life of the printer is
approximately 5 million lines.
To open the printer cover, lift up the cover as shown on
the right sketch.
the right sketch.
Your register is shipped with the print head release lever
held by a white retainer in the lifted up position. Be sure
to remove this retainer (see the figure at the right) and
push down the print head release lever before you use
the POS terminal.
held by a white retainer in the lifted up position. Be sure
to remove this retainer (see the figure at the right) and
push down the print head release lever before you use
the POS terminal.
Print head release lever
The print head can be lifted by the green
lever on the right side of the printer.
Pulling the lever forward lifts the print
head up. If the paper becomes jammed,
open the cutter unit pushing the cutter
open tab, then pull the lever further
forward to open the print head wider so
you can remove the jammed paper.
The print head can be lifted by the green
lever on the right side of the printer.
Pulling the lever forward lifts the print
head up. If the paper becomes jammed,
open the cutter unit pushing the cutter
open tab, then pull the lever further
forward to open the print head wider so
you can remove the jammed paper.
Cutter open tab
If a paper jam occurs, pull the cutter unit
open while pushing the cutter open tab.
Then remove the paper jam inside the
printer. For the detailed procedures, refer
to the “Removing a paper jam” section in
the “Operator Maintenance” chapter.
If a paper jam occurs, pull the cutter unit
open while pushing the cutter open tab.
Then remove the paper jam inside the
printer. For the detailed procedures, refer
to the “Removing a paper jam” section in
the “Operator Maintenance” chapter.
Do not attempt to remove the paper roll with the head in the down position. This may result in
damage to the printer and print head.
NOTE
NOTE
Printer cover
Retainer
Cutter open tab
Cutter unit
Print head release lever
Paper chute
Paper roll location
Take-up spool
10
RS232 Connector/SD Card Slot
■ Opening the RS232 connector cover
Push the part of the RS232 connector cover indicated by
the arrow to open the cover.
* To close the cover, push the arrowed part in until you hear
the arrow to open the cover.
* To close the cover, push the arrowed part in until you hear
it click.
■ Opening the SD card slot cover
Refer to the “SD CARD Mode” section.
Keyboard
■ Inserting the keyboard sheet
Insert the keyboard sheet between the keyboard cover and the cabinet as illustrated below.
1.
Insert the keyboard sheet into the slit, holding up the
keyboard cover as shown left.
keyboard cover as shown left.
2.
Close the keyboard cover.
• Do not spread the keyboard cover too far as it might tear.
• Replace the keyboard sheet with a new one if by chance it gets wet. Use of a wet keyboard sheet may
• Replace the keyboard sheet with a new one if by chance it gets wet. Use of a wet keyboard sheet may
cause problems.
• Be sure to use only SHARP-supplied keyboard sheets. Thick or hard sheets make key operation difficult.
• Smooth the keyboard sheet evenly under the keyboard cover, without any folds or wrinkles, to ensure
• Smooth the keyboard sheet evenly under the keyboard cover, without any folds or wrinkles, to ensure
easier operation.
• If you require a new keyboard sheet, please contact your dealer.
• The keyboard cover will eventually wear out. If your keyboard cover is dirty or broken, replace the cover
• The keyboard cover will eventually wear out. If your keyboard cover is dirty or broken, replace the cover
with a new one. For details, contact your authorized SHARP dealer.
NOTE
Keyboard sheet
Keyboard cover
Click on the first or last page to see other UP-800 (serv.man30) service manuals if exist.