Sharp XL-MP10H User Manual / Operation Manual ▷ View online
05/3/23
XL-MP10H(E)3.fm
21
TINSEA034SJZZ
XL-MP10H
Tape
Recordi
n
g
Recording on a cassette tape
Before recording:
!
When recording important selections, make a preliminary test to
ensure that the desired material is properly recorded.
ensure that the desired material is properly recorded.
!
SHARP is not liable for damage or loss of your recording arising
from malfunction of this unit.
from malfunction of this unit.
!
The volume and sound controls can be adjusted with no effect on
the recorded signal (Variable Sound Monitor).
the recorded signal (Variable Sound Monitor).
!
For recording, use only normal tapes. Do not use metal or
CrO tapes.
CrO tapes.
!
Do not use C-120 tapes or poor-quality tapes, as they may cause
malfunctions.
malfunctions.
"
Recording from a disc
Erase-prevention tab of cassette tapes:
!
When recording on a cassette tape,
make sure that the erase-prevention
tabs are not removed. Cassettes have
removable tabs that prevent acciden-
tal recording or erasing.
make sure that the erase-prevention
tabs are not removed. Cassettes have
removable tabs that prevent acciden-
tal recording or erasing.
!
To protect the recorded sound, re-
move the tab after recording. Cover
the tab hole with adhesive tape to
record on the tape without the tab.
move the tab after recording. Cover
the tab hole with adhesive tape to
record on the tape without the tab.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the FUNCTION button until "CD DISC" appears on
the display.
the display.
When operating with the remote control, press the CD button.
3
Load the desired disc.
4
Load a cassette into the cassette compartment with the
side to be recorded on facing you.
side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
performed.
5
Press the button.
6
Press the button, which also
engages the button.
engages the button.
7
Press the button again to cancel the pause mode.
8
Press the
( ) button to start recording.
Side A
Tab for
side B
side B
Tab for
side A
side A
6
05/3/23
XL-MP10H(E)3.fm
22
TINSEA034SJZZ
XL-MP10H
Tape
Recordi
n
g
Recording on a cassette tape (continued)
To perform programmed recording:
To interrupt recording:
Press the button.
To resume recording, press the button.
Press the button.
To resume recording, press the button.
To stop recording:
Press the button.
The tape will stop.
Press the button.
The tape will stop.
"
Recording from the radio
To stop recording:
Press the button.
Press the button.
Note:
If you hear a whistling noise whilst recording an AM station, move
the AM loop aerial.
If you hear a whistling noise whilst recording an AM station, move
the AM loop aerial.
"
Erasing recorded tapes
1
Programme tracks (see page 17).
2
Press the button.
3
Press the button, which also engages the button.
4
Press the button again to cancel the pause mode.
5
Press the
( ) button to start recording.
1
Tune in to the desired station (see page 18).
2
Load a cassette into the cassette compartment with the
side to be recorded on facing you.
side to be recorded on facing you.
Wind past the leader of the tape, on which recording cannot be
performed.
performed.
3
Press the button.
4
Press the button, which also
engages the button.
engages the button.
5
Press the button again to begin recording.
1
Load the tape to be erased into the cassette compartment with
the side to be erased facing toward you.
the side to be erased facing toward you.
2
Press the FUNCTION button until "TAPE" appears on the dis-
play.
When operating with the remote control, press the TAPE button.
play.
When operating with the remote control, press the TAPE button.
3
Press the button, which also engages the button to begin
erasing.
erasing.
05/3/23
XL-MP10H(E)3.fm
23
TINSEA034SJZZ
XL-MP10H
Advanc
e
d Featu
res
Timer and sleep operation
This may be operated only with the remote control.
Timer playback:
The unit turns on and plays the desired source (disc or tuner) at a
preset time.
The unit turns on and plays the desired source (disc or tuner) at a
preset time.
Sleep operation:
The radio or disc can be turned off automatically.
The radio or disc can be turned off automatically.
Note:
The timer and sleep operations are not available during tape mode.
Before setting timer:
The timer and sleep operations are not available during tape mode.
Before setting timer:
"
Timer playback
Continued to the next page
1
Check that the clock is set to the correct time (refer to page 11).
2
Load a disc to be played.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD or TUNER (BAND) button to select the de-
sired function.
When you selected the TUNER (BAND), tune in to the desired
station.
sired function.
When you selected the TUNER (BAND), tune in to the desired
station.
3
Adjust the volume using the VOLUME buttons.
Do not turn the volume up too high.
4
Press the TIMER button and within 6 seconds, press the
MEMORY button.
MEMORY button.
5
Within 1 minute, press the PRESET ( or ) button to
specify the hour to start, then press the MEMORY button.
specify the hour to start, then press the MEMORY button.
6
Within 1 minute, press the PRESET ( or ) button to
specify the minutes to start, then press the MEMORY but-
ton.
specify the minutes to start, then press the MEMORY but-
ton.
!
The timer playback starting time, function, and volume will be
displayed, and then the unit will enter the stand-by mode au-
tomatically.
displayed, and then the unit will enter the stand-by mode au-
tomatically.
!
" " will appear and the current time will be displayed.
To cancel the timer playback:
Press the ON/STAND-BY button to turn the power on.
Press the ON/STAND-BY button to turn the power on.
7
05/3/23
XL-MP10H(E)3.fm
24
TINSEA034SJZZ
XL-MP10H
Advanc
e
d Featu
res
Timer and sleep operation (continued)
To reset or change the timer setting:
Perform "Timer playback" from the beginning.
Perform "Timer playback" from the beginning.
"
Sleep operation
To cancel the sleep operation:
Press the ON/STAND-BY button whilst "SLEEP" is indicated.
To cancel the sleep operation without setting the system to the
stand-by mode, press the SLEEP button until "OFF" appears on the
display.
Press the ON/STAND-BY button whilst "SLEEP" is indicated.
To cancel the sleep operation without setting the system to the
stand-by mode, press the SLEEP button until "OFF" appears on the
display.
To confirm the remaining sleep time:
Press the SLEEP button once whilst the sleep timer is set.
The remaining sleep time is displayed for about 3 seconds.
Press the SLEEP button once whilst the sleep timer is set.
The remaining sleep time is displayed for about 3 seconds.
"
To use timer and sleep operation together
Example: To fall asleep and wake up to the same radio station
You can play back the same source only (the function cannot be
switched).
You can play back the same source only (the function cannot be
switched).
7
When the preset time is reached, playback will start.
The volume will increase gradually until it reaches the volume
you were listening at before your system enters the timer stand-
by mode.
you were listening at before your system enters the timer stand-
by mode.
8
The unit will enter the stand-by mode one hour after the
timer playback starts. However, when disc playback time is
one hour or less, it will enter the stand-by mode after com-
pleting playback.
timer playback starts. However, when disc playback time is
one hour or less, it will enter the stand-by mode after com-
pleting playback.
1
Play back the desired sound source.
2
Press the SLEEP button.
To change the sleep time:
Press the SLEEP button repeatedly to select the desired sleep
time. The time will decrease as follows.
time. The time will decrease as follows.
The amount of sleep time can also be changed whilst in the
sleep mode.
sleep mode.
(Maximum: 3 hours - Minimum: 5 minutes)
3
Your system will enter the power stand-by mode automat-
ically after the preset time has elapsed.
ically after the preset time has elapsed.
The volume will turn down 40 seconds before the sleep opera-
tion finishes.
tion finishes.
3:00
2:00
1:30
1:00
10
15
30
5
OFF
1
Set the sleep time (steps 1 - 2 on the left).
2
Whilst the sleep timer is set, set the desired playback time
(steps 4 - 6, page 23).
(steps 4 - 6, page 23).
Sleep timer setting
Timer playback setting
Sleep operation will
automatically stop.
automatically stop.
Timer playback
start time
start time
5 minutes - 3 hours
Click on the first or last page to see other XL-MP10H service manuals if exist.