Sharp XL-1000 User Manual / Operation Manual ▷ View online
13
XL-1000H(E)2.fm
01/1/17
Ba
sic Oper
ation
- Gener
a
l Contr
o
l -
General Control
„
To turn the power on
Press the ON/STAND-BY button to turn the power on.
To set the unit to stand-by mode:
Press the ON/STAND-BY button again.
„
To change the display brightness (2 levels)
You can switch the display brightness by pressing the DIMMER button on the remote
control.
control.
„
Opening and closing the CD compartment
The CD compartment cover is motorised.
When the power is turned on, you can open or close the CD compartment cover by
pressing the (OPEN/CLOSE) button.
pressing the (OPEN/CLOSE) button.
Caution:
z
Do not stop or move the CD compartment cover manually. It may cause malfunc-
tions to the unit.
tions to the unit.
z
Be careful not to jam your fingers in the CD compartment cover.
Dimmed
Brightened
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
14
XL-1000H(E)2.fm
01/1/17
Ba
sic Oper
ation
-
Soun
d Con
tr
o
l
-
Sound Control
„
Adjusting the volume
Press the VOLUME button to increase the volume and the VOLUME button for
decreasing.
decreasing.
„
Adjusting the bass
Main unit operation:
1
Press the BASS/TREBLE button until "BASS" appears on the display.
2
Within 5 seconds, press the VOLUME ( or ) button to adjust the bass.
Remote control operation:
Press the BASS ( or ) button to adjust the bass.
„
Adjusting the treble
Main unit operation:
1
Press the BASS/TREBLE button until "TRE" appears on the display.
2
Within 5 seconds, press the VOLUME ( or ) button to adjust the treble.
Remote control operation:
Press the TREBLE ( or ) button to adjust the treble.
2
1
28
29 MAX
MIN
.....
0
5
-5
...
...
0
5
-5
...
...
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
15
XL-1000H(E)2.fm
01/1/17
Ba
sic Oper
ation
- Se
tting t
h
e
Cloc
k
-
Setting the Clock
This may be operated only with the remote control.
In this example, the clock is set for the 24-hour (0:00) display.
Note:
The time will flash at the push of the CLOCK button when the AC power supply is
restored after a power failure or unplugging the unit.
Readjust the clock as follows.
restored after a power failure or unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the Clock" from the beginning.
To change the 24-hour or 12-hour display:
1
Press the CLOCK button and within 3 seconds, press the MEMORY
button.
button.
2
Within 1 minute, press the PRESET ( or ) button to select 24-
hour or 12-hour display and then press the MEMORY button.
hour or 12-hour display and then press the MEMORY button.
"0:00"
The 24-hour display will appear.
(0:00 - 23:59)
"AM 12:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
Note that this can only be set when the unit is first installed or it has been reset.
(Refer to step 3 under "If trouble occurs" on page 26.)
(Refer to step 3 under "If trouble occurs" on page 26.)
3
Within 1 minute, press the PRESET ( or ) button to adjust the
hour and then press the MEMORY button.
hour and then press the MEMORY button.
z
When the 12-hour display is selected, "AM" will change automatically to "PM".
4
Within 1 minute, press the PRESET ( or ) button to adjust the
minutes and then press the MEMORY button.
minutes and then press the MEMORY button.
z
The hour will not advance even if minutes advance from "59" to "00".
z
The clock starts from "0" second. (Seconds are not displayed.)
To confirm the time display when the power is on:
Press the CLOCK button.
The time display will appear for about 5 seconds.
The time display will appear for about 5 seconds.
1
Clear all the programmed contents. [Perform to step 3 under "If trouble occurs" on
page 26 for details.]
page 26 for details.]
2
Perform "Setting the Clock" from the beginning.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
16
XL-1000H(E)2.fm
01/1/17
C
D
P
lay
b
a
ck
- List
ening t
o
a
CD -
Listening to a CD
To interrupt playback:
Main unit operation:
Press the
Press the
button.
To resume playback from the same point, press the
button again.
Remote control operation:
Press the button.
To resume playback from the same point, press the button.
Press the button.
To resume playback from the same point, press the button.
To stop playback:
Press the button.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the FUNCTION button until "CD STOP" or "NO DISC" ap-
pears on the display.
pears on the display.
When operating with the remote control, press the CD button.
3
Press the (OPEN/CLOSE) button to open the CD compartment.
4
Place a CD on the spindle, label side up.
Be sure to place 8 cm (3") disc in the middle of a disc holder.
5
Press the (OPEN/
CLOSE) button to close
the CD compartment.
CLOSE) button to close
the CD compartment.
Total number of tracks
Total playing time
6
Press the
( ) button
to start playback from
track 1.
track 1.
When the last track on the disc has finished playing, the CD player will stop au-
tomatically.
tomatically.
12 cm (5")
8 cm (3")
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Click on the first or last page to see other XL-1000 service manuals if exist.