Sharp SD-PX15H (serv.man6) User Manual / Operation Manual ▷ View online
E-41
SD-PX15H_SEEG_E.fm
04/2/9
ENGLISH
TINSZA052AWZZ
SD-PX15H
Ra
dio Opera
tion
- Usi
n
g the
Radio Da
ta
S
y
stem (RDS
)
-
Using the Radio Data System (RDS) (continued)
"
Using the Auto Station Programme Mem-
ory (ASPM)
ory (ASPM)
Whilst in the ASPM operation mode, the tuner will automatically search for new RDS
stations. Up to 40 stations can be stored.
If you have already stored some stations in memory, the number of new stations you
can store will be less.
stations. Up to 40 stations can be stored.
If you have already stored some stations in memory, the number of new stations you
can store will be less.
To stop the ASPM operation before it is complete:
Set the MODE 1/MODE 2 switch to MODE 2 and press the ASPM button whilst it is
scanning for stations.
The stations which are already stored in memory will be kept there.
scanning for stations.
The stations which are already stored in memory will be kept there.
Notes:
!
If the same station is broadcasting on different frequencies, the strongest fre-
quency will be stored in memory.
quency will be stored in memory.
!
Any station which has the same frequency as one stored in memory will not be
stored.
stored.
!
If 40 stations have already been stored in memory, the scan will be aborted. If you
want to redo the ASPM operation, erase the preset memory.
want to redo the ASPM operation, erase the preset memory.
!
If no stations have been stored in memory, "END" will appear for about 4 seconds.
!
If the RDS signals are very weak, station names may not be stored in memory.
To erase all of the contents of preset memory:
To store a station name again if the wrong name was stored in mem-
ory:
ory:
It may be impossible to store station names in memory using the ASPM function if
there is lots of noise or if the signal is too weak. In this case, perform as follows.
there is lots of noise or if the signal is too weak. In this case, perform as follows.
Notes:
!
The same station name can be stored in different channels.
!
In a certain area or during certain time periods, the station names may temporarily
be different.
be different.
1
Press the TUNER/BAND button to select the FM band.
2
Set the MODE 1/MODE 2 switch to MODE 2 and press and hold
down the ASPM button for at least 3 seconds.
down the ASPM button for at least 3 seconds.
1
After "ASPM" has flashed for about 4 seconds, scanning will start (87.50 -
108.00 MHz).
108.00 MHz).
2
When an RDS station is found, "RDS" will appear for a short time and the sta-
tion will be stored in memory.
tion will be stored in memory.
3
After scanning, the number of stations stored in memory will be displayed for
4 seconds, and then "END" will appear for 4 seconds.
4 seconds, and then "END" will appear for 4 seconds.
1 Hold the CLEAR button down for 3 seconds or more.
2 Whilst "CLEAR" is displayed, press the ENTER button.
2 Whilst "CLEAR" is displayed, press the ENTER button.
!
After performing this operation, all of the preset memory information will be erased.
1 Press the TUNER PRESET ( or ) button to check whether the names are cor-
rect.
2 If you find a wrong name whilst receiving the station, wait until the correct name will
be displayed. And then press the ENTER button.
3 Within 5 seconds, press the TUNER PRESET ( or ) button to display the preset
channel to be corrected again.
4 Within 5 seconds, press the ENTER button.
!
The new station name has been stored in memory correctly.
E-42
SD-PX15H_SEEG_E.fm
04/2/9
ENGLISH
TINSZA052AWZZ
F
S
V
I
N
P
E
D
SD-PX15H
Ra
dio Opera
tion
- Usi
n
g the
Radio Da
ta
S
y
stem (RDS
)
-
"
To recall stations in memory
To specify programmed types and select stations (PTY search):
You can search a station by specifying the programme type (news, sports, traffic pro-
gramme, etc. ... see page 40) from the stations in memory.
gramme, etc. ... see page 40) from the stations in memory.
Notes:
!
If the display has stopped flashing, start again from step 3.
!
If you want to listen to the same programme type of another station, press the
PTY-TI button whilst the channel number or station name is flashing. The unit will
look for the next station.
PTY-TI button whilst the channel number or station name is flashing. The unit will
look for the next station.
!
If no station can be found, "NOTFOUND" will appear for 4 seconds.
If you select the traffic programme:
If you select the traffic programme (TP) in step 4, "TP" will appear. (This does not
mean that you can listen to the traffic information at that time.)
When the traffic information is broadcast, "TA" will appear.
mean that you can listen to the traffic information at that time.)
When the traffic information is broadcast, "TA" will appear.
To specify station names and select stations manually:
1
Press the TUNER/BAND button to select the FM band.
2
Set the MODE 1/MODE 2 switch to MODE 2 and press the PTY-TI
button.
button.
"PTY TI" and "SELECT" will appear alternately for about 6 seconds.
3
Within 6 seconds, press the or button to select the programme
type.
type.
Each time the button is pressed, the programme type will appear. If the button is
held down for more than 0.5 seconds, the programme type will appear continu-
ously.
held down for more than 0.5 seconds, the programme type will appear continu-
ously.
4
Whilst the selected programme type is flashing (within 6 seconds),
press the ENTER button.
press the ENTER button.
After the selected programme type has been lit for 2 seconds, "SEARCH" will ap-
pear, and the search operation will start.
pear, and the search operation will start.
1
Press the TUNER/BAND button to select the FM band.
2
Press the TUNER PRESET ( or ) button to select a desired station.
3
The station name will be displayed for 3 seconds. Then the display will change as
follows.
follows.
E-42
SD-PX15H_SEEG_E.fm
04/2/9
ENGLISH
TINSZA052AWZZ
F
S
V
I
N
P
E
D
SD-PX15H
Ra
dio Opera
tion
- Usi
n
g the
Radio Da
ta
S
y
stem (RDS
)
-
"
To recall stations in memory
To specify programmed types and select stations (PTY search):
You can search a station by specifying the programme type (news, sports, traffic pro-
gramme, etc. ... see page 40) from the stations in memory.
gramme, etc. ... see page 40) from the stations in memory.
Notes:
!
If the display has stopped flashing, start again from step 3.
!
If you want to listen to the same programme type of another station, press the
PTY-TI button whilst the channel number or station name is flashing. The unit will
look for the next station.
PTY-TI button whilst the channel number or station name is flashing. The unit will
look for the next station.
!
If no station can be found, "NOTFOUND" will appear for 4 seconds.
If you select the traffic programme:
If you select the traffic programme (TP) in step 4, "TP" will appear. (This does not
mean that you can listen to the traffic information at that time.)
When the traffic information is broadcast, "TA" will appear.
mean that you can listen to the traffic information at that time.)
When the traffic information is broadcast, "TA" will appear.
To specify station names and select stations manually:
1
Press the TUNER/BAND button to select the FM band.
2
Set the MODE 1/MODE 2 switch to MODE 2 and press the PTY-TI
button.
button.
"PTY TI" and "SELECT" will appear alternately for about 6 seconds.
3
Within 6 seconds, press the or button to select the programme
type.
type.
Each time the button is pressed, the programme type will appear. If the button is
held down for more than 0.5 seconds, the programme type will appear continu-
ously.
held down for more than 0.5 seconds, the programme type will appear continu-
ously.
4
Whilst the selected programme type is flashing (within 6 seconds),
press the ENTER button.
press the ENTER button.
After the selected programme type has been lit for 2 seconds, "SEARCH" will ap-
pear, and the search operation will start.
pear, and the search operation will start.
1
Press the TUNER/BAND button to select the FM band.
2
Press the TUNER PRESET ( or ) button to select a desired station.
3
The station name will be displayed for 3 seconds. Then the display will change as
follows.
follows.
E-42
SD-PX15H_SEEG_E.fm
04/2/9
ENGLISH
TINSZA052AWZZ
F
S
V
I
N
P
E
D
SD-PX15H
Ra
dio Opera
tion
- Usi
n
g the
Radio Da
ta
S
y
stem (RDS
)
-
"
To recall stations in memory
To specify programmed types and select stations (PTY search):
You can search a station by specifying the programme type (news, sports, traffic pro-
gramme, etc. ... see page 40) from the stations in memory.
gramme, etc. ... see page 40) from the stations in memory.
Notes:
!
If the display has stopped flashing, start again from step 3.
!
If you want to listen to the same programme type of another station, press the
PTY-TI button whilst the channel number or station name is flashing. The unit will
look for the next station.
PTY-TI button whilst the channel number or station name is flashing. The unit will
look for the next station.
!
If no station can be found, "NOTFOUND" will appear for 4 seconds.
If you select the traffic programme:
If you select the traffic programme (TP) in step 4, "TP" will appear. (This does not
mean that you can listen to the traffic information at that time.)
When the traffic information is broadcast, "TA" will appear.
mean that you can listen to the traffic information at that time.)
When the traffic information is broadcast, "TA" will appear.
To specify station names and select stations manually:
1
Press the TUNER/BAND button to select the FM band.
2
Set the MODE 1/MODE 2 switch to MODE 2 and press the PTY-TI
button.
button.
"PTY TI" and "SELECT" will appear alternately for about 6 seconds.
3
Within 6 seconds, press the or button to select the programme
type.
type.
Each time the button is pressed, the programme type will appear. If the button is
held down for more than 0.5 seconds, the programme type will appear continu-
ously.
held down for more than 0.5 seconds, the programme type will appear continu-
ously.
4
Whilst the selected programme type is flashing (within 6 seconds),
press the ENTER button.
press the ENTER button.
After the selected programme type has been lit for 2 seconds, "SEARCH" will ap-
pear, and the search operation will start.
pear, and the search operation will start.
1
Press the TUNER/BAND button to select the FM band.
2
Press the TUNER PRESET ( or ) button to select a desired station.
3
The station name will be displayed for 3 seconds. Then the display will change as
follows.
follows.
Display
