Sharp SD-EX220 User Manual / Operation Manual ▷ View online
E-8
SD-EX220H
ENGLISH
2
3
4
5
6
7
8
1
SD-EX220H(H)_E.fm
03/6/9
TINSZ0953AWZZ
Prepar
ation for
Us
e
- S
y
s
te
m
c
onne
c
ti
o
n
s
-
Using antislip speaker cushions:
You can install speakers either vertically or horizontally.
Affix the cushions (supplied) to the bottom of the speakers to prevent them from slid-
ing or falling due to vibration.
Affix the cushions (supplied) to the bottom of the speakers to prevent them from slid-
ing or falling due to vibration.
" Aerial connection
Installing the AM loop aerial:
External FM or AM aerial:
Use an external FM or AM aerial if you require better reception. Consult your dealer.
Note:
When using an external AM aerial, be sure to keep the wire of the AM loop aerial
connected.
connected.
" How to close side covers
When completing the connection, close the side covers (be careful not to trap the
wires).
wires).
" Connecting the AC power lead
After checking all the connections have been made correctly, plug the AC power lead
of the unit into the wall socket.
of the unit into the wall socket.
Note:
Unplug the AC power lead from the wall socket if the unit will not be in use for a pro-
longed period of time.
longed period of time.
(Horizontal position)
(Vertical position)
Supplied FM aerial:
Connect the FM aerial wire to the FM 75 OHMS
socket and position the FM aerial wire in the direction
where the strongest signal can be received.
socket and position the FM aerial wire in the direction
where the strongest signal can be received.
Supplied AM loop aerial:
Connect the AM loop aerial wire to the AM and GND
terminals. Position the AM loop aerial for optimum re-
ception. Place the AM loop aerial on a shelf, etc., or
attach it to a stand or a wall with screws (not sup-
plied).
terminals. Position the AM loop aerial for optimum re-
ception. Place the AM loop aerial on a shelf, etc., or
attach it to a stand or a wall with screws (not sup-
plied).
Note:
Placing the aerial on the unit or near the AC power
lead may cause noise pickup. Place the aerial away
from the unit for better reception.
lead may cause noise pickup. Place the aerial away
from the unit for better reception.
< Assembling >
< Attaching to the wall >
Black
White
Wall
Screws
(Not supplied)
(Not supplied)
External AM aerial
15 m (49 feet)
15 m (49 feet)
7.5 m
(25 feet)
(25 feet)
External FM aerial
Earth wire
Earth rod
75 ohm coaxial
cable
cable
Speaker wire
FM aerial wire
AM loop aerial wire
AC power lead
Wall socket
(AC 230 V, 50 Hz)
(AC 230 V, 50 Hz)
E-9
SD-EX220H
ENGLISH
SD-EX220H(H)_E.fm
03/6/9
TINSZ0953AWZZ
Prepar
ation for
Us
e
-
T
o
i
n
st
all t
h
e m
a
in
u
n
it
an
d
sp
e
ake
rs o
n
t
h
e w
a
ll -
To install the main unit and speakers on the wall
CAUTION:
! Be very careful to prevent the main unit [3.7 kg (8.2 lbs.)] from falling when mount-
ing on the wall.
! Before mounting, check the wall strength. (Do not put to the veneer plaster or
whitewashed wall. The main unit or speakers may fall.) If it is not clear, consult
with a qualified service technician.
with a qualified service technician.
! Mounting screws are not supplied. Use appropriate ones.
! Check all mounting screws for looseness and that they are engaged in the main
! Check all mounting screws for looseness and that they are engaged in the main
unit and speakers.
! Mount the main unit and speakers on the wall with 2 screws for each.
! Select a good location. If not, accidents may occur or the unit may get damaged.
! Avoid placing on a bed, sofa, water tank, sink and hallway wall.
! To avoid accidents, fix the speaker wires to the wall. You may trip over them.
! SHARP is not responsible for accidents resulting from improper installation.
! Select a good location. If not, accidents may occur or the unit may get damaged.
! Avoid placing on a bed, sofa, water tank, sink and hallway wall.
! To avoid accidents, fix the speaker wires to the wall. You may trip over them.
! SHARP is not responsible for accidents resulting from improper installation.
" Driving screws
Sharp designed the main unit and speakers so you may hang them on the wall.
Use proper screws (not supplied). See below for size and type.
Use proper screws (not supplied). See below for size and type.
" Installing the main unit
1
Make a hole in the wall using a drill.
2
Drive a wall mount plug into the hole using a hammer, until it is
flush with the wall surface.
flush with the wall surface.
5 mm (3/16")
3.2 mm (1/8")
Min. 22 mm (7/8")
9 mm (3/8")
32 mm (1-1/4")
8-9 mm (3/8")
3
Drive two screws into the wall for main unit and each speaker, as
shown in the illustration.
shown in the illustration.
! Make sure that both the screw and the wall can support a load of 20 kg (45
lbs.).
! Drive the screws, so the screw head extends about 5.5 mm (7/32") out from
the wall.
1
Fix the pattern paper and drive two screws into the wall with a dis-
tance of 160 mm (6-5/16") in between.
tance of 160 mm (6-5/16") in between.
2
Tighten the screws and remove the paper. Hook the main unit on
the screw heads and make sure it is secure.
the screw heads and make sure it is secure.
Put the left speaker wire in the groove on the back of the main unit.
Wall mounting screw
Wall surface
Wall surface
5.5 mm (7/32")
Pattern paper
for main unit
for main unit
160 mm (6-5/16")
Wall surface
Speaker wire
E-10
SD-EX220H
ENGLISH
2
3
4
5
6
7
8
1
SD-EX220H(H)_E.fm
03/6/9
TINSZ0953AWZZ
Prepar
ation for
Us
e
-
T
o
i
n
st
all t
h
e m
a
in
u
n
it
an
d
sp
e
ake
rs o
n
t
h
e w
a
ll -
" Installing speakers
Notes:
! Place speakers with the tweeter on the outside. Left and right speakers should
always be positioned symmetrically.
! There are four VESA (*) screw holes on the back of the main unit and speakers.
You can also use commercially available fittings for mounting.
! Be sure to install the product according to the method recommended by the
bracket manufacturer.
(*) VESA (Video Electronics Standards Association) is an organization to promote
the standardization of digital imaging device for PCs.
the standardization of digital imaging device for PCs.
1
Fix the pattern paper and drive two screws into the wall with a dis-
tance of 160 mm (6-5/16") in between. When mounting vertically,
set the distance to 110 mm (4-5/16").
tance of 160 mm (6-5/16") in between. When mounting vertically,
set the distance to 110 mm (4-5/16").
2
Tighten the screws and remove the paper. Hook the speaker on the
screw heads and make sure it is secure.
screw heads and make sure it is secure.
Put the speaker wire in the groove on the back of the speaker.
Pattern paper
for speaker
for speaker
(Horizontal position)
(Vertical position)
160 mm (6-5/16")
Pattern paper
for speaker
for speaker
110 mm (4-5/16")
(Horizontal position)
(Vertical position)
Wall surface
Wall surface
Speaker
wire
Speaker
wire
(Horizontal position)
(Vertical position)
Tweeter
Tweeter
Tweeter
Tweeter
(Main unit)
(Speaker)
E-11
SD-EX220H
ENGLISH
SD-EX220H(H)_E.fm
03/6/9
TINSZ0953AWZZ
Prepar
ation for
Us
e
- Ge
ne
ra
l c
o
ntr
o
l -
General control
! To turn the power on
Press the ON/STAND-BY button to turn the power on.
If the power does not turn on, check the AC power lead is plugged in properly.
Note:
When turning on the power immediately after it is set to the stand-by mode, wait a
few seconds.
few seconds.
! To change the display brightness (2 levels)
When the power is on, you can switch the display brightness by pressing the DIS-
PLAY button on the remote control.
PLAY button on the remote control.
! Volume control
Press the VOLUME (+ or -) button to increase or decrease the volume.
! Bass control
! Treble control
! Surround
Press the SURROUND button to allow you to enjoy music that seems to surround
you. "SURROUND" will appear.
To cancel the surround mode, press the SURROUND button again.
you. "SURROUND" will appear.
To cancel the surround mode, press the SURROUND button again.
After use:
Press the ON/STAND-BY button to enter the power stand-by mode.
For example, CD function
Dimmer on
Dimmer off
1
Press the BASS/TREBLE button to select "BASS".
2
Within 3 seconds, press the VOLUME (+ or -) button to adjust the bass.
1
Press the BASS/TREBLE button to select "TREBLE".
2
Within 3 seconds, press the VOLUME (+ or -) button to adjust the treble.
SURROUND indicator
"SURROUND" will go out.
2
1
39
40
0
.....
+5
-5
+5
-5
14
SHARP
T
INSZ0
9
53
A
WZZ
(H
)
Click on the first or last page to see other SD-EX220 service manuals if exist.