Sharp SD-AT1000 User Manual / Operation Manual ▷ View online
E-12
SD-AT1000H_SEEG_E.fm
03/3/14
SD-AT1000H
ENGLISH
2
3
4
5
6
7
8
1
TINSZ0943AWZZ
Sy
stem
c
o
nne
c
tions
- A
udio c
o
nne
c
tions
to D
V
D
pla
y
e
rs
, VCRs
, TV
s
, e
tc
. -
!
Audio connection to TVs or other equip-
ment
ment
You can enjoy surround sound from TVs or other equipment by connecting
them to the unit as shown.
them to the unit as shown.
!
Using other subwoofer
For a greater emphasis of bass, a commercially available subwoofer, with a
built in amplifier, can be connected to the unit using the SUBWOOFER PRE
OUT socket.
built in amplifier, can be connected to the unit using the SUBWOOFER PRE
OUT socket.
Notes:
"
No sound is heard from the speaker in which an amplifier is not built in.
"
When not using the supplied subwoofer, disconnect the speaker wire from the
main unit.
main unit.
"
The speaker delay and level settings are applied to the subwoofer connected to
the SUBWOOFER PRE OUT socket (see pages 23 and 24).
the SUBWOOFER PRE OUT socket (see pages 23 and 24).
!
Connecting the AC power lead
After checking all the connections have been made correctly, plug the AC power lead
of this unit into the wall socket.
of this unit into the wall socket.
Note:
Unplug the AC power lead from the wall socket if the unit will not be in use for a pro-
longed period of time.
longed period of time.
Caution:
Turn off all other equipment before making this connection.
Notes:
"
Refer to the operation manual of the equipment to be connected.
"
Insert the plugs fully to avoid fuzzy pictures or noise.
TV
To audio
output sockets
output sockets
To audio
input sockets
input sockets
Audio cable
(commercially available)
Other
equipment
equipment
To audio
output sockets
output sockets
To audio
input sockets
input sockets
Audio cable
(commercially
available)
(commercially
available)
Audio signal
Audio signal
To subwoofer
input socket
input socket
Audio cable
(commercially available)
Commercially
available subwoofer
(amplifier built in)
available subwoofer
(amplifier built in)
To subwoofer
output socket
output socket
Subwoofer signal
Wall socket
(AC 230 V, 50 Hz)
(AC 230 V, 50 Hz)
E-13
SD-AT1000H_SEEG_E.fm
03/3/14
SD-AT1000H
ENGLISH
TINSZ0943AWZZ
Pr
epara
tion f
o
r Us
e
- S
yst
em
in
st
alla
ti
o
n
-
System installation
!
Placing the speaker system
The best surround effect will be achieved by placing each speaker at the same
distance from the listening position.
It is recommended to arrange the speakers as shown below.
distance from the listening position.
It is recommended to arrange the speakers as shown below.
Notes:
"
Place the TV halfway between the front speakers.
"
It is recommended that the centre speaker be placed near the television.
"
Place the surround speakers at a position just above the height of your ears.
"
The subwoofer vibrates whilst reproducing bass. Place it on a stable, sturdy sur-
face.
face.
"
The subwoofer reproduces bass. Place it anywhere you like.
!
Magnetically shielded speakers
The front, centre and subwoofer speakers may be placed beside or near the TV as
they are magnetically shielded. However, discolouration may occur depending on the
TV type.
they are magnetically shielded. However, discolouration may occur depending on the
TV type.
If colour variation occurs...
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
After 15 - 30 minutes, turn the TV on again.
If the colour variation is still present...
Move the speakers further away from the TV.
Refer to the user's manual of the TV for details.
Refer to the user's manual of the TV for details.
Note:
The surround speakers are not magnetically shielded.
Note:
The default distance is set to 2 m. If speakers cannot be placed at equal distances,
refer to "Speaker delay setting" (see page 23).
refer to "Speaker delay setting" (see page 23).
Installation image:
The speaker stands and speaker wall brackets are optionally available (see page 2).
Refer to their instructions for assembly.
Refer to their instructions for assembly.
Front
speaker (left)
Subwoofer
Front
speaker (right)
speaker (right)
Surround
speaker (left)
speaker (left)
Surround
speaker (right)
speaker (right)
Default setting:
2 m
2 m
Centre
speaker
Front speaker (left)
Same distance
Front speaker (right)
Centre speaker
Same distance
E-14
SD-AT1000H_SEEG_E.fm
03/3/14
SD-AT1000H
ENGLISH
2
3
4
5
6
7
8
1
TINSZ0943AWZZ
Pr
epara
tion f
o
r Us
e
- Re
mot
e
c
ontr
o
l -
Remote control
!
Battery installation
Precautions for battery use:
"
Replace all old batteries with new ones at the same time.
"
Do not mix old and new batteries.
"
Remove the batteries if the unit is not to be used for long periods of time. This will
prevent potential damage due to battery leakage.
prevent potential damage due to battery leakage.
Caution:
"
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
"
Installing the batteries incorrectly may cause the unit to malfunction.
Notes concerning use:
"
Replace the batteries if the operating distance is reduced or if the operation
becomes erratic. Purchase 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
becomes erratic. Purchase 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
"
Periodically clean the transmitter on the remote control and the sensor on the unit
with a soft cloth.
with a soft cloth.
"
Exposing the sensor on the unit to strong light may interfere with operation.
Change the lighting or the direction of the unit.
Change the lighting or the direction of the unit.
"
Keep the remote control away from moisture, heat, shock, and vibrations.
!
Test of the remote control
Check the remote control after checking all the connections (see pages 9 - 12).
Point the remote control directly at the remote sensor on the unit.
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy your
system.
system.
1 Open the battery cover.
2 Insert the batteries according to the direction indicated in the bat-
2 Insert the batteries according to the direction indicated in the bat-
tery compartment.
When inserting or removing the batteries, push them towards the battery termi-
nals.
nals.
3 Close the cover.
0.2 m - 6 m
(8" - 20')
(8" - 20')
Remote sensor
E-15
SD-AT1000H_SEEG_E.fm
03/3/14
SD-AT1000H
ENGLISH
TINSZ0943AWZZ
Pr
epara
tion f
o
r Us
e
- Ge
ne
ra
l c
o
ntr
o
l -
General control
!
To turn the power on
Press the ON/STAND-BY button.
If the power does not turn on, check the AC power lead is plugged in properly.
To set the unit to stand-by mode:
Press the ON/STAND-BY button again.
!
To change the display brightness (2 levels)
!
Volume control
!
Muting
!
Headphones
"
Before plugging in or unplugging the headphones, reduce the volume.
"
Be sure your headphones have a 6.3 mm (1/4") diameter plug and are between 16
ohms and 50 ohms impedance. The recommended impedance is 32 ohms.
ohms and 50 ohms impedance. The recommended impedance is 32 ohms.
"
Plugging in the headphones disconnects the speakers automatically. Adjust the
volume using the VOLUME control.
volume using the VOLUME control.
"
You cannot use the surround feature with headphones.
"
Do not plug in or unplug headphones whilst recording. The sound may skip.
Display
You can switch the display brightness by press-
ing the DIMMER button.
ing the DIMMER button.
Dimmed
Main unit operation:
When the VOLUME control is turned clockwise,
the volume will increase. When it is turned anti-
clockwise, the volume will decrease.
the volume will increase. When it is turned anti-
clockwise, the volume will decrease.
Remote control operation:
Press the VOLUME + button to increase the vol-
ume and the VOLUME - button for decreasing.
ume and the VOLUME - button for decreasing.
The volume is muted temporarily when pressing
the MUTING button on the remote control.
Press again to restore the volume.
the MUTING button on the remote control.
Press again to restore the volume.
0
1
2
39
40
.....
Click on the first or last page to see other SD-AT1000 service manuals if exist.