Sharp SD-AT1000 User Manual / Operation Manual ▷ View online
E-8
SD-AT1000H_SEEG_E.fm
03/3/14
SD-AT1000H
ENGLISH
2
3
4
5
6
7
8
1
TINSZ0943AWZZ
G
e
n
e
ral In
fo
rmatio
n
- Contr
o
ls
a
nd indic
a
to
rs
-
!
Speaker functions
Notes:
"
Do not allow any objects to fall into or to be placed in the bass reflex ducts.
"
The speakers grilles are not removable.
"
Front, centre and subwoofer speakers are magnetically shielded.
!
Using antislip speaker cushions
You can install the front, centre or surround speakers either vertically or horizontally.
Affix the cushions (supplied) to the bottom of the speakers to prevent them from slid-
ing or falling due to vibration.
Affix the cushions (supplied) to the bottom of the speakers to prevent them from slid-
ing or falling due to vibration.
A sheet of speaker cushions (20 pcs.) is supplied with this product. Use 4 cushions
per speaker.
per speaker.
!
Carrying the subwoofer
When carrying the subwoofer, be careful not to touch the subwoofer located near bot-
tom. It may be damaged. Be sure to hold the unit by its base.
tom. It may be damaged. Be sure to hold the unit by its base.
Front speaker:
Reproduces left and right sound (for the stereo mode) or front surround sound.
Centre speaker:
Reproduces centre surround sound.
Surround speaker:
Reproduces rear surround sound.
Subwoofer:
Reproduces bass sound.
(For speaker installation, refer to page 13.)
(Vertical position)
(Horizontal position)
Subwoofer
E-9
SD-AT1000H_SEEG_E.fm
03/3/14
SD-AT1000H
ENGLISH
TINSZ0943AWZZ
Sy
stem
c
o
nne
c
tions
- S
p
e
a
k
e
r c
onne
c
tion
-
Speaker connection
The speaker terminals on the main unit, the tube and plugs of the speaker lead, and speaker labels are distinguished by colours.
Connect the speaker and the unit by matching the colours.
(For speaker installation, refer to page 13.)
Connect the speaker and the unit by matching the colours.
(For speaker installation, refer to page 13.)
Subwoofer
Front speaker
(left)
Centre speaker
Front speaker
(right)
Surround speaker
(right)
Surround speaker
(left)
Blue
White
Red
Green
Green
Purple
Blue
Black
Red
Black
Red
Black
Red
Red
Black
Red
White
Black
Red
Grey
Black
Red
Instead of the supplied sub-
woofer, you can connect sepa-
rately available woofer to en-
joy more of the bass sound
(see page 12).
woofer, you can connect sepa-
rately available woofer to en-
joy more of the bass sound
(see page 12).
Purple
Grey
E-10
SD-AT1000H_SEEG_E.fm
03/3/14
SD-AT1000H
ENGLISH
2
3
4
5
6
7
8
1
TINSZ0943AWZZ
Sy
stem
c
o
nne
c
tions
- S
p
e
aker
connec
tion /
Aer
ial c
o
n
n
e
c
tion -
!
Connecting speaker wires
To prevent accidental short circuit between and terminals, connect the
speaker wires to the speakers first then to the unit.
speaker wires to the speakers first then to the unit.
Caution:
"
The supplied speakers are exclusively for SD-AT1000H. Do not connect them
to other equipment, and do not connect other speakers to SD-AT1000H. It
may cause malfunction.
to other equipment, and do not connect other speakers to SD-AT1000H. It
may cause malfunction.
"
Do not mistake the and , and right and left terminals of the speaker leads. (The
right speaker is placed on the right when you face the unit.)
right speaker is placed on the right when you face the unit.)
Aerial connection
Notes:
"
Placing the aerial on the unit or near the AC power lead may cause noise pickup.
Place the aerial away from the unit for better reception.
Place the aerial away from the unit for better reception.
"
When static is still heard even after adjusting the position of the AM loop aerial, try
reversing the wire connections.
reversing the wire connections.
Installing the AM loop aerial:
External FM or AM aerial:
Use an external FM or AM aerial if you require better reception. Consult your dealer.
When using an external AM aerial, be sure to keep the wire of the AM loop aerial
connected.
When using an external AM aerial, be sure to keep the wire of the AM loop aerial
connected.
Make sure to leave the AC power lead disconnected when connecting the
speakers.
speakers.
"
Do not let the bare speaker wires touch each other.
"
Do not stand or sit on the speakers. You may be injured.
"
Insert the speaker plug fully with the rising side facing up.
"
Hold the speaker plug when removing it from the main unit.
Pulling the lead may cause malfunction to the unit.
Pulling the lead may cause malfunction to the unit.
Incorrect
1
Connect the wires to the speakers.
2
Connect the other end to the main unit.
Speaker terminals
Speaker plug
Plug in with the rising
side facing up.
side facing up.
Label
Label
Tube
Red
Black
Supplied FM aerial:
Connect the FM aerial wire to the FM 75 OHMS
socket and position the FM aerial wire in the di-
rection where the strongest signal can be re-
ceived.
socket and position the FM aerial wire in the di-
rection where the strongest signal can be re-
ceived.
Supplied AM loop aerial:
Connect the AM loop aerial wire to the AM and
GND terminals. Position the AM loop aerial for
optimum reception. Place the AM loop aerial on
a shelf, etc., or attach it to a stand or a wall with
screws (not supplied).
GND terminals. Position the AM loop aerial for
optimum reception. Place the AM loop aerial on
a shelf, etc., or attach it to a stand or a wall with
screws (not supplied).
< Assembling >
< Attaching to the wall >
Wall
Screws
(not
supplied)
White
Black
FM aerial
AM loop
aerial
External FM
aerial
External AM
aerial
15 m (49 feet)
7.5 m (25 feet)
AM loop
aerial
Earth wire
Earth rod
E-11
SD-AT1000H_SEEG_E.fm
03/3/14
SD-AT1000H
ENGLISH
TINSZ0943AWZZ
Sy
stem
c
o
nne
c
tions
- A
udio c
o
nne
c
tions
to D
V
D
pla
y
e
rs
, VCRs
, TV
s
, e
tc
. -
Audio connections to DVD players, VCRs, TVs, etc.
!
Connecting a DVD player (CD player), digi-
tal tuner, etc.
tal tuner, etc.
Notes:
"
This unit has DIGITAL IN 1 (coaxial) and DIGITAL IN 2 (optical) sockets for digital
input. Select either according to the output socket of your equipment.
input. Select either according to the output socket of your equipment.
"
When connecting with an optical digital cable, set the digital output of the digital
tuner to PCM. Refer to the operation manual of the digital tuner.
tuner to PCM. Refer to the operation manual of the digital tuner.
!
Connecting a VCR, etc.
Notes:
"
The LINE 1 OUT sockets emit signals from the LINE 2 IN, LINE 3 IN and the built-
in tuner. Signals from the DIGITAL IN and LINE 1 IN are not emitted.
in tuner. Signals from the DIGITAL IN and LINE 1 IN are not emitted.
"
Connect TV directly to the DVD player, VCR or digital tuner to watch programmes
(refer to the operation manual of each equipment).
(refer to the operation manual of each equipment).
Digital audio cable
(commercially
available)
(commercially
available)
Optical digital cable
(option:AD-M3DC)
(option:AD-M3DC)
TV
TV
Digital tuner, etc.
DVD player
(CD player), etc.
(CD player), etc.
To optical digital
audio input socket
audio input socket
To optical digital
audio output socket
audio output socket
To coaxial digital
audio input socket
audio input socket
To coaxial digital
audio output socket
audio output socket
Audio signal
Audio signal
VCR, etc.
To audio
output sockets
output sockets
To audio
output sockets
output sockets
To audio
input sockets
input sockets
To audio
input sockets
input sockets
Audio cable
(commercially
available)
(commercially
available)
Audio cable
(commercially
available)
(commercially
available)
TV
A
udio signal
A
udio signal
Click on the first or last page to see other SD-AT1000 service manuals if exist.