Sharp HT-SB200 User Manual / Operation Manual ▷ View online
9
HT-SB200
2008 December 16
HT-SB200_A6_EN.fm
Preparation f
or Use
Caution:
●
Be very careful to prevent the speaker [1.75 kg (3.86 lbs.)]
from falling when mounting on the wall.
from falling when mounting on the wall.
●
Before mounting, check the wall strength. (Do not put on the
veneer plaster or whitewashed wall. The speaker may fall.) If
unsure, consult a qualified service technician.
veneer plaster or whitewashed wall. The speaker may fall.) If
unsure, consult a qualified service technician.
●
Mounting screws are not supplied. Use appropriate ones.
●
Check all wall mount angle screws for looseness.
●
Select a good location. If not, accidents may occur or the
speaker may get damaged.
speaker may get damaged.
●
SHARP is not responsible for accidents resulting from
improper installation.
improper installation.
■
Driving screws
SHARP designed the speakers so you may hang them on the
wall. Use proper screws (not supplied). See below for size and
type.
wall. Use proper screws (not supplied). See below for size and
type.
■
Wall mount angle fixed to the wall
(Horizontal position)
(Horizontal position)
Continued to the next page
To mount the speaker on the wall
3.2 mm (1/8")
9 mm (3/8")
Min. 22 mm (7/8")
5 mm
(3/16")
(3/16")
1
Fix the pattern paper to the wall in horizontal position
as below.
as below.
2
Make a hole on the wall following the screw point
marks on the pattern paper by using a drill.
marks on the pattern paper by using a drill.
3
Fix a wall mount plug into the hole using a hammer,
until it is flush with the wall surface.
until it is flush with the wall surface.
29 mm
29 mm
44 mm
44 mm
509 mm
Pattern paper
Wall surface
Wall surface
8-9 mm (3/8")
32 mm (1-1/4")
Wall surface
8-9 mm (3/8")
32 mm (1-1/4")
10
HT-SB200
2008 December 16
HT-SB200_A6_EN.fm
Preparation f
or Use
Speaker preparation (continued)
Note:
Make sure all screws are fully tighten. (screws are not supplied)
■
Installing the speaker
4
Screw the wall mount angle to the wall as shown in the
illustration. (Total screw is 8 pieces)
illustration. (Total screw is 8 pieces)
Wall surface
Wall mount angle
Wall mount angle
Wall surface
Wall surface
Wall mount angle
(screws x 4)
(screws x 4)
1
Align the wall mount slot at the speaker to the wall
mount angle.
mount angle.
2
Slot the speaker into the wall mount angle.
3
Fix them securely.
Wall surface
11
HT-SB200
2008 December 16
HT-SB200_A6_EN.fm
Preparation f
or Use
Placing the speaker
Installation image:
Place the speaker as shown.
Notes:
●
As the sound from the speaker is omni-directional, you can
place the speaker anywhere you like. However, it is
recommended to place it as close to the TV as possible.
place the speaker anywhere you like. However, it is
recommended to place it as close to the TV as possible.
●
The front panel of the speaker is not removable.
Caution:
●
Do not change the installation direction when the speaker is
turned on.
turned on.
●
Do not stand or sit on the speaker as you may be injured.
Falling prevention
Safety wires (not supplied) are useful to prevent the speaker
from falling off the table.
from falling off the table.
Loop the safety wires (not supplied) into each hole as shown and
tie the safety wires to the LCD TV stand.
tie the safety wires to the LCD TV stand.
TV
VCR
DVD player
12
HT-SB200
2008 December 16
HT-SB200_A6_EN.fm
Preparation f
or Use
Speaker connections to TVs
Caution:
Turn off all other equipment before making any connections.
Tuner receiving for other audio system
●
Placing the aerial near the speaker AC power lead may cause
noise pick up. Place the aerial away from the speaker for
better reception.
noise pick up. Place the aerial away from the speaker for
better reception.
Notes:
●
To connect to TV, use either LINE IN 1 sockets or AUDIO
LINE IN 2 socket only.
LINE IN 2 socket only.
●
Refer the operation manual of the equipment to be
connected.
connected.
●
Fully insert the plugs to avoid fuzzy pictures or noises.
■
Connecting to a TV
If the TV/monitor has an audio output, connect it to the LINE IN
1 sockets on the rear of the speaker.
1 sockets on the rear of the speaker.
■
Connecting to a TV (with Headphone socket)
If the TV/monitor has headphone socket, connect it to the
AUDIO LINE IN 2 socket on the rear of the speaker.
AUDIO LINE IN 2 socket on the rear of the speaker.
Notes:
●
If the TV volume is continuously in low level, the speaker will
automatically power off. Increase the TV output volume to
enjoy the sound from the speaker.
automatically power off. Increase the TV output volume to
enjoy the sound from the speaker.
●
If the speaker volume is continuously in very high level, the
speaker will mute and recover after 3 seconds.
speaker will mute and recover after 3 seconds.
To audio output sockets
RCA cable (supplied)
Speaker
TV
To LINE IN 1
sockets
sockets
HEADPHONE
To HEADPHONE socket
Audio cable
(3.5 mm/stereo socket)
(not supplied)
Speaker
TV
To AUDIO LINE
IN 2 socket
IN 2 socket
Click on the first or last page to see other HT-SB200 service manuals if exist.