DOWNLOAD Sharp HT-CN500DVH Service Manual ↓ Size: 3.72 MB | Pages: 61 in PDF or view online for FREE

HTCN400_500DVH_E.fm

03/7/2

HT-CN400DVH

92LCN400E0270

F

S

V

I

N

P

E

D

HT-CN500DVH

!

 

!

!

When this product is subjected to strong external interference (mechanical shock,
excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is
operated incorrectly, it may malfunction.

When short-circuiting the speaker leads or turning the volume too high, the protection
circuit may be activated and the system may enter the stand-by mode.
Unplug the unit and, after 15 minutes or more, plug it in again.
Turn down the volume if set too high.
 
 

!

 
 

!

Sudden temperature changes, storage or operation in an extremely humid environ-
ment may cause condensation inside the cabinet (laser pickup, etc.) or on the trans-
mitter on the remote control.
Condensation can cause the unit to malfunction. If this happens, leave the power on
with no disc in the unit until normal playback is possible (about 1 hour). Wipe off any
condensation on the transmitter with a soft cloth before operating the unit.

The radio makes unusual 
noises continuously.

"

Is the unit placed near the TV or 
computer?

"

Is the FM aerial or AM loop aerial 
placed properly? Move the aerial 
away from the AC power lead or the 
unit if located near.

P. 12

The preset channel cannot 
be recalled.

"

Did you remove the plug from the 
wall socket, or did a power failure 
occur?

P. 40

Set the channel again.

The remote control does not 
operate properly.

"

Is the battery polarity respected?

P. 16

"

Are the batteries dead?

"

Is the distance or angle incorrect?

P. 16

"

Are there any obstructions in front of 
the unit?

"

Is the remote control sensor ex-
posed to strong light (inverter fluo-
rescent light, direct sunlight, etc.)?

P. 16

"

Is the remote control for another 
equipment used simultaneously?

The unit cannot be turned on 
with the remote control.

"

Is the AC power lead of the unit 
plugged in?

P. 14

"

Are the batteries inserted?

P. 16

1

Set the unit to the stand-by mode and turn the power on again.

2

If the unit is not restored in the previous operation, unplug and plug in the unit, and 
then turn the power on.

Remove the disc inserted in the unit.

HTCN400_500DVH_E.fm

03/7/2

HT-CN400DVH

92LCN400E0270

HT-CN500DVH

!

 
 

!

DVD/CD discs are fairly resistant to damage, however mistracking can occur due to
an accumulation of dirt on the disc surface. Follow the guidelines below for maximum
enjoyment from your DVD/CD collection and player.

"

Do not write on either side of the disc, particularly the non-label side from which
signals are read. Do not mark this surface.

"

Keep your discs away from direct sunlight, heat, and excessive moisture.

"

Always hold the DVD/CDs by the edges. Fingerprints, dirt, or water on the DVD/
CDs can cause noise or mistracking. If a DVD/CD is dirty or does not play properly,
clean it with a soft, dry cloth, wiping straight out from the centre, along the radius.

As part of our policy of continuous improvement, SHARP reserves the right to make
design and specification changes for product improvement without prior notice. The
performance specification figures indicated are nominal values of production units.
There may be some deviations from these values in individual units.

"

"

Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then with a 
dry cloth.
 

"

Do not use chemicals for cleaning (petrol, paint thinner, etc.). It may damage the 
cabinet finish.

"

Do not apply oil to the inside of the unit. It may cause malfunctions.

AC 230 V, 50 Hz

HT-CN400DVH:

Power on: 88 W

Power stand-by: 0.6 W

HT-CN500DVH:

Power on: 105 W

Power stand-by: 0.6 W

Width: 430 mm (16-7/8") 
Height: 53 mm (2-1/8") 
Depth: 337 mm (13-1/4")

4.2 kg (9.3 lbs.)

Analogue input (IN 1): RCA type   1 pair (L/R)

Analogue input (IN 2): RCA type   1 pair (L/R)

Analogue output (OUT): RCA type   1 pair (L/R)

Headphones: 16 - 50 ohms (recommended: 32 ohms)

SCART output: SCART terminal   1

S-video output: S-terminal   1

Video output: RCA type   1

Front speakers:

RMS: 60 W (30 W + 30 W) (10 % T.H.D., 1 kHz)

Centre speaker:

RMS: 30 W (10 % T.H.D., 1 kHz)

Surround speakers:

RMS: 60 W (30 W + 30 W) (10 % T.H.D., 1 kHz)

Subwoofer:

RMS: 50 W (10 % T.H.D., 100 Hz)

7

SHARP 9

2

L

CN4

0

0

E

0

2

7

0

HTCN400_500DVH_E.fm

03/7/2

HT-CN400DVH

92LCN400E0270

F

S

V

I

N

P

E

D

HT-CN500DVH

"

"

"

"

"

"

Front speakers:

RMS: 100 W (50 W + 50 W) (10 % T.H.D., 1 kHz)

Centre speaker:

RMS: 50 W (10 % T.H.D., 1 kHz)

Surround speakers:

RMS: 100 W (50 W + 50 W) (10 % T.H.D., 1 kHz)

Subwoofer:

RMS: 50 W (10 % T.H.D., 100 Hz)

PAL/NTSC colour

DVD (Region number 2, ALL), SVCD, VCD, audio CD, 
CD-R, CD-RW, MP3

Horizontal resolution: 500 lines

S/N ratio: 70 dB

Linear PCM DVD:

4 Hz to 22 kHz (sampling rate: 
48 kHz)

4 Hz to 44 kHz (sampling rate: 
96 kHz)

CD: 4 Hz to 20 kHz

CD: 96 dB (1 kHz)

Linear PCM DVD: 95 dB

CD: 94 dB

0.006 % maximum

FM: 87.5 -108 MHz

AM: 522 - 1,620 kHz

Full range speaker system (magnetic shield)

8 cm (3-1/8") speaker

Maximum input power HT-CN400DVH:  45 W

HT-CN500DVH:  60 W

HT-CN400DVH:  8 ohms

HT-CN500DVH:  6 ohms

Width: 94 mm (3-3/4") 
Height: 169 mm (6-5/8") 
Depth: 97 mm (3-7/8")

0.6 kg (1.3 lbs.)/each

Full range speaker system

8 cm (3-1/8") speaker

Maximum input power HT-CN400DVH:  45 W

HT-CN500DVH:  60 W

HT-CN400DVH:  8 ohms

HT-CN500DVH:  6 ohms

Width: 94 mm (3-3/4") 
Height: 169 mm (6-5/8") 
Depth: 97 mm  (3-7/8")

0.6 kg (1.3 lbs.)/each

Sub-woofer system

12 cm (4-3/4") subwoofer

Maximum input power 75 W

6 ohms

Width: 135 mm (5-5/16") 
Height: 338 mm (13-5/16") 
Depth: 375 mm (14-3/4")

5.3 kg (11.7 lbs.)

92LCN400E0270
03G R AO  1

HTCN400_500DVH(H)            92LCN400E0270