DOWNLOAD Sharp CD-SW200E Service Manual ↓ Size: 3.53 MB | Pages: 44 in PDF or view online for FREE

 

05/3/8

CD-SW200E 24- 31.fm

 

CD-SW200E

  

 

 

  

To remove the cassette, press the   (TAPE  ) button, and then
open the compartment.

  

Before changing from one tape operation to another, press the 
(TAPE ) 

button.

  

If a power failure occurs during tape operation, the tape head will
remain engaged with the tape and the cassette door will not open.
In this case, wait until the power is restored.

 

Press in the stop 
mode.

 

Press in the playback, 
fast forward or rewind 
mode.

 

Press in the playback 
or stop mode.

(TAPE 2 
only)

  

When recording important selections, make a preliminary test to 
ensure that the desired material is properly recorded.

  

SHARP is not liable for damage or loss of your recording arising 
from malfunction of this unit.

  

The volume and sound controls can be adjusted with no effect 
on the recorded signal (Variable Sound Monitor).

  

 

 

When recording on a cassette tape, make sure that the erase-
prevention tabs are not removed. Cassettes have removable 
tabs that prevent accidental recording or erasing.

To protect the recorded sound, remove the tab after recording. 
Cover the tab hole with adhesive tape to record on the tape with-
out the tab.

Side A

Tab for side B

Tab for side A

05/3/8

CD-SW200E 24- 31.fm

CD-SW200E

You can record the desired disc using the DIRECT PLAY button.

To stop recording:
Press the   (TAPE  ) button.
The disc and tape will stop.

Wind past the leader of the tape, on which recording cannot be 
performed.

Recording will be paused.

Recording is started from the selected disc. When the play-
back of the last track is finished or the end of the tape is 
reached, the disc and the cassette will stop automatically.

Playback of the disc will start approximately 7 seconds after 
the tape starts.

05/3/8

CD-SW200E 24- 31.fm

CD-SW200E

To stop recording:
Press the   (TAPE  ) button.
The disc and tape will stop.
 

To interrupt recording:
Press the 

 button.

To resume recording, press the   /   (TAPE  ) button.

To stop recording:
Press the   (TAPE  ) button.

Note:
If you hear a whistling noise whilst recording an AM station, move the
AM loop aerial.

You can record from TAPE 1 to TAPE 2.

To stop dubbing:
Press the   (TAPE  ) button.
TAPE 1 and TAPE 2 will stop simultaneously.
 

Note:
Make sure that the TAPE 1 is not in use.

1 Perform steps 1 - 5 in "Recording from a CD or MP3/WMA disc" 

on page 30.

2 Within 5 seconds, press the   /   (TAPE  ) button to start record-

ing.

1 Programme discs and tracks (see page 21).
2 Press the 

 button.

3 Press the   /   (TAPE  ) button to start recording.

Wind past the leader of the tape, on which recording cannot be 
performed.

Recording will be paused.

It is recommended that the recording tape is the same length as 
the master tape.

Recording will be paused.

1

Load the tape to be erased into the TAPE 2 cassette compart-
ment with the side to be erased facing towards you.

2

Press the TAPE (1   2) button until "TAPE 2" appears on the dis-
play.

3

Press the 

 button.

4

Press the   /   (TAPE  ) button to start erasing.

05/3/8

CD-SW200E 32-41 .fm

CD-SW200E

Timer playback:
The unit turns on and plays the desired source (CD, tuner, tape) at a
preset time.

Timer recording:
The unit turns on and starts recording from the tuner at the preset
time.

 
Using the once timer and daily timer in combination:
For example, use the once timer to record a radio programme, and
use the daily timer to wake up.

Note:
When set times for the daily timer and once timer overlap, the once
timer takes priority. Allow an interval of at least 1 minute between op-
erations.

  

 

 

 

Once timer play or once timer recording works for 
one time only at a preset time.

For example, if you are away but want to record a programme on a 
radio station.

 

 

Daily timer play or daily timer recording works at 
the same preset time every day.

For example, set the timer as a wake-up call every morning.

1

Set the daily timer (pages 32 - 34).

2

Set the once timer (pages 32 - 34).

Start

Daily timer

Once timer

1 minute or more

Stop

Start

Stop

 

1 Check that the clock is set to the correct time (refer to page 15).

If it is not set, you cannot use the timer function.

2 For timer playback: Load a cassette or discs to be played.

For timer recording: Load a cassette for recording in the cas-

sette compartment.

 

Set the clock to the correct time if "ONCE" or "DAILY" does not 
appear.