Sharp CD-ES222E User Manual / Operation Manual ▷ View online
25
CD-ES222E
03/10/29
CD-ES222E(UK).fm
TINSEA002SJZZ
Adv
anced F
eatures
Enhancing your system
The connection lead is not included. Purchase a commercially avail-
able lead as shown below.
able lead as shown below.
Listening to the playback sounds from VCR,
DVD, etc.
DVD, etc.
Note:
To prevent noise interference, place the unit away from the televi-
sion.
To prevent noise interference, place the unit away from the televi-
sion.
To record on a tape
Headphones
z
Before plugging in or unplugging the headphones, reduce the vol-
ume.
ume.
z
Be sure your headphones have a 3.5 mm (1/8") diameter plug and
are between 16 ohms and 50 ohms impedance. The recommend-
ed impedance is 32 ohms.
are between 16 ohms and 50 ohms impedance. The recommend-
ed impedance is 32 ohms.
z
Plugging in the headphones disconnects the speakers automati-
cally. Adjust the volume using the VOLUME buttons.
cally. Adjust the volume using the VOLUME buttons.
VCR, DVD, etc.
To the line
output sockets
output sockets
Red
RCA lead
(not supplied)
(not supplied)
White
Red White
1
Use a connection lead to connect the VCR, DVD, etc. to the
VIDEO/AUX IN sockets.
VIDEO/AUX IN sockets.
When using video equipment, connect the audio output to this
unit and the video output to a television.
unit and the video output to a television.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the VIDEO/AUX button.
4
Play the connected equipment.
1
Insert a cassette in the TAPE 2 cassette compartment.
2
Press the VIDEO/AUX button.
3
Press the REC PAUSE (TAPE-2
) button.
4
Press the / button.
5
Play the VCR, DVD, etc.
8
26
CD-ES222E
03/10/29
CD-ES222E(UK).fm
TINSEA002SJZZ
Referenc
es
Troubleshooting chart
Many potential problems can be resolved by the owner without call-
ing a service technician.
If something is wrong with this product, check the following before
calling your authorised SHARP dealer or service centre.
ing a service technician.
If something is wrong with this product, check the following before
calling your authorised SHARP dealer or service centre.
General
CD player
Tuner
Cassette deck
Symptom
Possible cause
z
The clock is not set to the
correct time.
correct time.
z
Did a power failure occur? Reset
the clock. (Refer to page 12.)
the clock. (Refer to page 12.)
z
When a button is pressed,
the unit does not respond.
the unit does not respond.
z
Set the unit to the power stand-
by mode and then turn it back on.
by mode and then turn it back on.
z
If the unit still malfunctions, reset
it. (Refer to page 27.)
it. (Refer to page 27.)
z
No sound is heard.
z
Is the volume level set to "0"?
z
Are the headphones connected?
z
Are the speaker wires discon-
nected?
nected?
Symptom
Possible cause
z
Playback does not start.
z
Is the disc loaded upside down?
z
Playback stops in the mid-
dle or is not performed
properly.
dle or is not performed
properly.
z
Does the disc satisfy the stan-
dards?
dards?
z
Is the disc distorted or
scratched?
scratched?
z
Playback sounds are
skipped, or stopped in the
middle of a track.
skipped, or stopped in the
middle of a track.
z
Is the unit located near excessive
vibrations?
vibrations?
z
Is the disc very dirty?
z
Has condensation formed inside
the unit?
the unit?
Symptom
Possible cause
z
The radio makes unusual
noises continuously.
noises continuously.
z
Is the unit placed near the TV or
computer?
computer?
z
Is the FM/AM loop aerial placed
properly? Move the aerial away
from the AC power lead if it's lo-
cated nearby.
properly? Move the aerial away
from the AC power lead if it's lo-
cated nearby.
Symptom
Possible cause
z
Cannot record.
z
Is the erase-prevention tab re-
moved?
moved?
z
Cannot record tracks with
proper sound quality.
proper sound quality.
z
Is it a normal tape? (You cannot
record on a metal or CrO tape.)
record on a metal or CrO tape.)
z
Cannot erase completely.
z
Sound skipping.
z
Is there slack in the tape?
z
Is the tape stretched?
z
Cannot hear treble.
z
Are the capstans, pinch rollers,
or heads dirty?
or heads dirty?
z
Sound fluctuation.
z
Cannot remove the tape.
z
If a power failure occurs during
playback, the heads remain en-
gaged with the tape. Do not open
the compartment with great
force.
playback, the heads remain en-
gaged with the tape. Do not open
the compartment with great
force.
27
CD-ES222E
03/10/29
CD-ES222E(UK).fm
TINSEA002SJZZ
Referenc
es
Remote control
If trouble occurs
When this product is subjected to strong external interference (me-
chanical shock, excessive static electricity, abnormal supply voltage
due to lightning, etc.) or if it is operated incorrectly, it may malfunc-
tion.
chanical shock, excessive static electricity, abnormal supply voltage
due to lightning, etc.) or if it is operated incorrectly, it may malfunc-
tion.
If such a problem occurs, do the following:
1
1
Set the unit to the stand-by mode and turn the power on again.
2
If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.
plug in the unit, and then turn the power on.
Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
If neither operation above restores the unit, clear all the memory by
resetting it.
Clearing all the memory (reset)
1
Press the ON/STAND-BY button to enter the power stand-by
mode.
mode.
2
Whilst pressing down the CLOCK button and the DISC SKIP but-
ton, press the ON/STAND-BY button until "CLEAR" appears.
ton, press the ON/STAND-BY button until "CLEAR" appears.
Caution:
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD programme.
Condensation
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet (CD
pickup, tape heads, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc (or cassette) in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on
the transmitter with a soft cloth before operating the unit.
humid environment may cause condensation inside the cabinet (CD
pickup, tape heads, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc (or cassette) in the unit until normal
playback is possible (about 1 hour). Wipe off any condensation on
the transmitter with a soft cloth before operating the unit.
Before transporting the unit
Symptom
Possible cause
z
The remote control does
not operate.
not operate.
z
Is the AC power lead of the unit
plugged in?
plugged in?
z
Are the batteries inserted cor-
rectly?
rectly?
z
Are the batteries dead?
z
Does the range or angle of use
exceed that shown on page 10?
exceed that shown on page 10?
z
Does the remote control sensor
receive strong light?
receive strong light?
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button.
3
Press the OPEN/CLOSE button to open the disc tray.
Remove all CDs inserted in the unit.
Remove all CDs inserted in the unit.
4
Press the OPEN/CLOSE button to close the disc tray.
Make sure that "NO DISC" is displayed.
Make sure that "NO DISC" is displayed.
5
Press the ON/STAND-BY button to enter the stand-by mode,
and then unplug the AC power lead from the wall socket.
and then unplug the AC power lead from the wall socket.
9
28
CD-ES222E
03/10/29
CD-ES222E(UK).fm
TINSEA002SJZZ
Referenc
es
Maintenance
Cleaning the tape-handling parts
z
Dirty heads, capstans or pinch rollers can cause poor sound and
tape jams. Clean these parts with a cotton swab moistened with
commercial head/pinch roller cleaner or isopropyl alcohol.
tape jams. Clean these parts with a cotton swab moistened with
commercial head/pinch roller cleaner or isopropyl alcohol.
z
When cleaning the heads, pinch rollers, etc., unplug the unit from
the mains supply.
the mains supply.
z
After long use, the deck's heads and capstans may become mag-
netised, causing poor sound. Demagnetise these parts once
every 30 hours of playing/recording time by using a commercial
tape head demagnetiser. Read the demagnetiser's instructions
carefully before use.
netised, causing poor sound. Demagnetise these parts once
every 30 hours of playing/recording time by using a commercial
tape head demagnetiser. Read the demagnetiser's instructions
carefully before use.
Cleaning the CD pickup lens
Poor performance during CD playback (skipping or jumping) can be
caused by a dirty or contaminated CD laser pick up lens. If this hap-
pens then the use of a commercially available CD lens cleaning
discs may restore normal operation. Contact your supplier or local
CD software dealer to obtain CD lens cleaning discs. Ensure all
included instructions/documentation are carefully followed.
caused by a dirty or contaminated CD laser pick up lens. If this hap-
pens then the use of a commercially available CD lens cleaning
discs may restore normal operation. Contact your supplier or local
CD software dealer to obtain CD lens cleaning discs. Ensure all
included instructions/documentation are carefully followed.
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
Caution:
solution, then with a dry cloth.
Caution:
z
Do not use chemicals for cleaning (petrol, paint thinner, etc.). It
may damage the cabinet finish.
may damage the cabinet finish.
z
Do not apply oil to the inside of the unit. It may cause malfunc-
tions.
tions.
Specifications
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product im-
provement without prior notice. The performance specification fig-
ures indicated are nominal values of production units. There may be
some deviations from these values in individual units.
the right to make design and specification changes for product im-
provement without prior notice. The performance specification fig-
ures indicated are nominal values of production units. There may be
some deviations from these values in individual units.
General
Amplifier
Playback head
Erase head
Capstan
Recording/Playback head
Pinch roller
TAPE 1
TAPE 2
B
C
A
D
B
C
E
Power source
AC 230 - 240 V, 50 Hz
Power
consumption
consumption
50 W
Dimensions
Width: 270 mm (10-5/8")
Height: 305 mm (12")
Depth: 342 mm (13-1/2")
Height: 305 mm (12")
Depth: 342 mm (13-1/2")
Weight
5.8 kg (12.8 lbs.)
Output power
RMS: 40 W (20 W + 20 W) (10 % T.H.D.)
RMS: 30 W (15 W + 15 W) (0.9 % T.H.D.)
Output terminals
Speakers: 8 ohms
Headphones: 16 - 50 ohms (recommended:
32 ohms)
32 ohms)
Input terminals
Video/Auxiliary (audio signal): 500 mV/47 k
ohms
ohms
Click on the first or last page to see other CD-ES222E service manuals if exist.