Sharp CD-DP2400H User Manual / Operation Manual ▷ View online
12
CD-DP2400H(E)2.fm
01/7/17
CD-DP2400H
Prepara
tion f
o
r U
s
e
- S
y
s
te
m
c
onne
c
tion
s
-
System connections (continued)
!
Placing the speaker system
To enjoy the surround effect, we recommend that you place each speaker as shown
to the below.
to the below.
Installation of the surround speakers:
If possible, mount the surround speakers on the wall. Install them 60 cm - 90 cm (23"
- 35") above the height of your ears when you are seated.
- 35") above the height of your ears when you are seated.
!
To mount the surround speakers on the wall
The design of the surround speakers allows them to be hung on the wall. Be sure to
use the type and size of screw that is shown to the below.
use the type and size of screw that is shown to the below.
!
Connecting the AC power lead
After making all connections, plug the unit. If you plug the unit first,
the unit will enter the demonstration mode.
the unit will enter the demonstration mode.
Note:
Unplug the AC power lead from the wall socket if the unit will not be in use for a pro-
longed period of time.
longed period of time.
Notes:
"
The front speakers and the centre speaker are magnetically shielded.
Therefore, they do not affect the display even you use them near the TV. However,
some colour variation may occur, depending on the type of TV used.
Therefore, they do not affect the display even you use them near the TV. However,
some colour variation may occur, depending on the type of TV used.
If colour variation occurs...
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
After 15 - 30 minutes, turn the TV on again.
If the colour variation is still present...
Move the front speakers further away from the TV.
"
If any kind of magnet or an electromagnet is placed too close to the TV and the sys-
tem, irregular colours may appear on the TV screen.
tem, irregular colours may appear on the TV screen.
Main unit
Front speaker
(Left)
(Left)
Front speaker
(Right)
(Right)
Surround speaker
(Left)
(Left)
Surround speaker
(Right)
(Right)
TV
Centre speaker
Wall
Example: when installed on the wall
Example: when installed vertically
60 - 90 cm
(23" - 35")
(23" - 35")
1
Make a hole in the wall using a
drill.
drill.
2
Drive a wall mount plug into the
hole using a hammer. Drive the
wall mount plug in until it is flush
with the wall surface.
hole using a hammer. Drive the
wall mount plug in until it is flush
with the wall surface.
3
Drive one screw into the wall
mount plug for each speaker.
mount plug for each speaker.
Drive the screws, so there is about a 5
mm (3/16") space between the wall and
the head of the screw.
mm (3/16") space between the wall and
the head of the screw.
4
Mount the surround speaker on
the wall so that the screw head is
inserted into the slot on the sur-
round speaker.
the wall so that the screw head is
inserted into the slot on the sur-
round speaker.
5 mm (3/16")
3.2 mm (1/8")
Min. 22 mm (7/8")
9 mm (3/8")
32 mm (1-1/4")
8-9 mm (3/8")
Wall mounting screw
Wall surface
Wall surface
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
13
CD-DP2400H(E)2.fm
01/7/17
CD-DP2400H
B
asic Ope
ration
- Ge
ne
ra
l c
o
ntr
o
l -
General control
!
Demonstration mode
To cancel the demonstration mode:
When the unit is in the power stand-by mode (demonstration mode), press the
X-BASS/DEMO button. The demonstration mode will be cancelled and the display
will disappear.
X-BASS/DEMO button. The demonstration mode will be cancelled and the display
will disappear.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS/DEMO button again.
Note:
When the power is on, the X-BASS/DEMO button can be used to select the extra
bass mode.
bass mode.
!
To turn the power on
Press the ON/STAND-BY button to turn the power on.
To set the unit to stand-by mode:
Press the ON/STAND-BY button again.
!
To change the display brightness (2 levels)
You can switch the display brightness by pressing the DIMMER button.
!
Volume control
Main unit operation:
When the VOLUME control is turned clockwise, the volume will increase. When it is
turned anti-clockwise, the volume will decrease.
turned anti-clockwise, the volume will decrease.
Remote control operation:
Press the VOLUME button to increase the volume and the VOLUME button for
decreasing.
decreasing.
!
Bass control
When the power is first turned on, the unit will enter the extra bass mode which
emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra
bass mode, press the X-BASS/DEMO (X-BASS) button.
emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra
bass mode, press the X-BASS/DEMO (X-BASS) button.
!
Equaliser
When the EQ (EQUALIZER MODE) button is pressed, the current mode setting will
be displayed. To change to a different mode, press the EQ (EQUALIZER MODE) but-
ton repeatedly until the desired sound mode appears.
be displayed. To change to a different mode, press the EQ (EQUALIZER MODE) but-
ton repeatedly until the desired sound mode appears.
The first time the unit is plugged in, the unit will
enter the demonstration mode. You will see
words scroll.
enter the demonstration mode. You will see
words scroll.
Dimmed
Brightened
X-BASS indicator
The sound is not modified.
Bass and treble are emphasised.
Bass and treble are slightly emphasised.
Treble is cut a little.
Treble is reduced a lot.
Vocals (midrange tones) are emphasised.
0
1
2
29
30 MAXIMUM
.....
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
14
CD-DP2400H(E)2.fm
01/7/17
CD-DP2400H
B
asic Ope
ration
-
S
e
tting the
c
loc
k
-
Setting the clock
In this example, the clock is set for the 24-hour (0:00) display.
Note:
The "CLOCK" or time will flash at the push of the CLOCK button when the AC power
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
supply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from the beginning. If the time display is flashing, step 3
(for selecting the 24-hour or 12-hour display) will be skipped.
(for selecting the 24-hour or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK button and within 5 seconds, press the MEMO-
RY/SET button.
RY/SET button.
3
Press the TUNING/TIME ( or ) button to select 24-hour or 12-
hour display and then press the MEMORY/SET button.
hour display and then press the MEMORY/SET button.
"0:00"
The 24-hour display will appear.
(0:00 - 23:59)
"AM 12:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"AM 0:00"
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
Note that this can only be set when the unit is first installed or it has been reset.
[Refer to "Clearing all the memory (reset)" on page 30 for details.]
[Refer to "Clearing all the memory (reset)" on page 30 for details.]
4
Press the TUNING/TIME ( or ) button to adjust the hour and then
press the MEMORY/SET button.
press the MEMORY/SET button.
"
Press the TUNING/TIME ( or ) button once to advance the time by 1 hour.
Hold it down to advance continuously.
Hold it down to advance continuously.
"
When the 12-hour display is selected, "AM" will change automatically to "PM".
5
Press the TUNING/TIME ( or ) button to adjust the minutes and
then press the MEMORY/SET button.
then press the MEMORY/SET button.
"
Press the TUNING/TIME ( or ) button once to advance the time by 1
minute. Hold it down to change the time in 5-minute intervals.
minute. Hold it down to change the time in 5-minute intervals.
"
The hour will not advance even if minutes advance from "59" to "00".
"
The clock begins counting from "0" seconds. (Seconds are not displayed.)
The time display will disappear after a few seconds.
The time display will disappear after a few seconds.
To confirm the time display:
Press the CLOCK button.
The time display will appear for about 5 seconds.
The time display will appear for about 5 seconds.
1
Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on
page 30 for details.]
page 30 for details.]
2
Perform "Setting the clock" from the beginning.
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
15
CD-DP2400H(E)2.fm
01/7/17
CD-DP2400H
CD Pla
y
ba
c
k
- L
ist
en
in
g
t
o
a CD
(
C
Ds)
-
Listening to a CD (CDs)
Continued to the next page
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CD button.
3
Press the OPEN/CLOSE button to open the disc tray.
4
Place the CD(s) on the disc tray, label side up.
When loading a third disc, press the DISC SKIP button to turn the
disc tray, then place the CD in the open position.
disc tray, then place the CD in the open position.
"
CDs can be placed on any open position on the disc tray.
"
Be sure to place 8 cm (3") CD(s) in the middle of the disc positions.
5
Press the OPEN/CLOSE button to close the disc tray.
Music schedule
Total number of tracks on the
CD whose number is flashing
CD whose number is flashing
Total playing time of the CD whose
number is flashing
number is flashing
The music schedule will display only the number of tracks on the disc.
If the CD contains more than 15 tracks, "
" will appear.
6
To select the CD you want to listen to first, press one of the DISC-
1 - DISC-3 buttons.
1 - DISC-3 buttons.
12 cm (5")
8 cm (3")
Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)
Click on the first or last page to see other CD-DP2400H service manuals if exist.