Sharp CD-CH1000 User Manual / Operation Manual ▷ View online
9
General Information
Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)
■
Speaker system
Power amplifier
Mid-to-high range
(200 Hz - 20 kHz)
(200 Hz - 20 kHz)
Ultra-low range
(60 Hz - 200 Hz)
(60 Hz - 200 Hz)
Pre-amplifier
Pre-amplifier
Power amplifier
L-ch
Tweeter
Woofer
Sub-
woofer
woofer
Speaker grilles are removable:
Make sure nothing comes into contact with the
speaker diaphragms when you remove the
speaker grilles.
speaker diaphragms when you remove the
speaker grilles.
0
1.
Tweeter
4.
Subwoofer
0
2.
Woofer
5.
Subwoofer Terminals
0
3.
Bass Reflex Duct
6.
Main Speaker Terminals
1
2
3
4
5
6
Placing the speaker system:
There is no distinction between the right and
the left speakers.
the left speakers.
Right speaker
Left speaker
Bi-amp system:
This product drives the built-in subwoofer unit and the speaker unit composed of the
tweeter and woofer for mid-to-high range frequencies with independent amplifiers which
have individual frequency characteristics.
By amplifying separately the two frequency bands, clearer sound is achieved.
tweeter and woofer for mid-to-high range frequencies with independent amplifiers which
have individual frequency characteristics.
By amplifying separately the two frequency bands, clearer sound is achieved.
There are two sounds from the subwoofer.
One comes out from the bass reflex duct and
the other rebounds from the wall behind the
speaker.
One comes out from the bass reflex duct and
the other rebounds from the wall behind the
speaker.
10
Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)
Preparation for Use
System Connections
FM aerial
Right
speaker
speaker
Left
speaker
speaker
AM loop aerial
2
3
1
Right speaker
Left speaker
Blue
Black
Red
Wall socket
(
(
AC 230 V, 50 Hz
)
*CH1000H_P10_12(Preparation)
00.7.7, 3:13 PM
10
11
Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)
Preparation for Use
■
Aerial connection
Supplied FM aerial :
Connect the FM aerial wire to the FM 75 OHMS socket and position the FM
aerial wire in the direction where the strongest signal can be received.
Connect the FM aerial wire to the FM 75 OHMS socket and position the FM
aerial wire in the direction where the strongest signal can be received.
Supplied AM loop aerial :
Connect the AM loop aerial to the AM LOOP socket. Position the AM loop
aerial for optimum reception. Place the AM loop aerial on a shelf, etc., or
attach it to a stand or a wall with screws (not supplied).
Connect the AM loop aerial to the AM LOOP socket. Position the AM loop
aerial for optimum reception. Place the AM loop aerial on a shelf, etc., or
attach it to a stand or a wall with screws (not supplied).
Notes:
●
Placing the aerial on the stereo system or near the AC power lead may cause noise
pickup.
Place the aerial away from the stereo system for better reception.
pickup.
Place the aerial away from the stereo system for better reception.
●
Do not connect the attached FM aerial to an external FM aerial. Otherwise, trouble
may occur.
may occur.
Installing the AM loop aerial:
Assembling
1
2
3
4
Attaching to the wall
External FM aerial:
Use an external FM aerial if you require better reception.
Consult your dealer.
Consult your dealer.
External FM aerial
■
Speaker connection
Main terminals (left side of the rear):
Connect the blue wire to the (+) and the black one to the (–).
Connect the blue wire to the (+) and the black one to the (–).
Subwoofer terminals (right side of the rear):
Connect the red wire to the (+) and the black one to the (–).
Connect the red wire to the (+) and the black one to the (–).
Caution:
●
Connect the speaker wires to the speakers first, then to the unit.
●
Never mistake the MAIN and the SUBWOOFER terminals.
The stereo system or the speakers may be damaged .
The stereo system or the speakers may be damaged .
●
Only the included speakers should be used with this product.
Do not use other speakers with this unit or use the supplied speakers with other
units.
Do not use other speakers with this unit or use the supplied speakers with other
units.
●
Do not mistake the right and the left channels.
The right speaker is the one on the right side when you face the unit.
The right speaker is the one on the right side when you face the unit.
●
Do not let the bare speaker wires touch each other.
,,
,,
Incorrect
Incorrect
●
Do not stand or sit on the speakers. You may be injured.
■
Connecting the AC power lead
After making all connections, plug the unit.
If you plug the unit first, the unit will enter the demonstration mode (see page 13).
If you plug the unit first, the unit will enter the demonstration mode (see page 13).
Note:
Unplug the unit if it will not be used for a prolonged period of time.
Unplug the unit if it will not be used for a prolonged period of time.
Wall
Screws
*CH1000H_P10_12(Preparation)
00.7.7, 3:13 PM
11
12
Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)
Preparation for Use
■
Battery installation
1. Remove the battery cover.
2. Insert the supplied batteries according to the direction indicated in
2. Insert the supplied batteries according to the direction indicated in
the battery compartment.
●
When inserting or removing the batteries, push them towards the
ë
battery
terminals.
3. Replace the cover.
Precautions for battery use:
●
Replace all old batteries with new ones at the same time.
●
Do not mix old and new batteries.
●
Remove the batteries if the unit will not be used for long periods of time. This will
prevent potential damage due to battery leakage.
prevent potential damage due to battery leakage.
Caution:
●
Do not use rechargeable batteries (nickel-cadmium battery, etc.).
●
Installing the batteries incorrectly may cause the unit to malfunction.
Notes concerning use:
●
Replace the batteries if the operating distance is reduced or if the operation be-
comes erratic.
Purchase 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
comes erratic.
Purchase 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
●
Periodically clean the transmitter on the remote control and the sensor on the ste-
reo system with a soft cloth.
reo system with a soft cloth.
●
Exposing the sensor on the stereo system to strong light may interfere with opera-
tion. Change the lighting or the direction of the stereo system.
tion. Change the lighting or the direction of the stereo system.
●
Keep the remote control away from moisture, heat, shock, and vibrations.
■
Test of the remote control
Face the remote control directly to the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy the
music.
music.
0.2 m - 6 m
(8" - 20')
(8" - 20')
Remote Control
Remote sensor
*CH1000H_P10_12(Preparation)
00.7.7, 3:13 PM
12
Click on the first or last page to see other CD-CH1000 service manuals if exist.