Sharp CD-BA250 (serv.man4) Service Manual ▷ View online
– 17 –
CD-BA250H/CD-BA2600H
TEST MODE
• Setting the test mode
Any one of test mode can be set by pressing several keys as follows.
<X-BASS> + <CD> + <POWER> TEST:CD operation test.
Any one of test mode can be set by pressing several keys as follows.
<X-BASS> + <CD> + <POWER> TEST:CD operation test.
Function:-CD test mode.
-Enter test mode.
-Enter test mode.
C D T E S T
OPEN/CLOSE operation is using manual.
<<
>>, <<
>> buttons make pick's slide possible.
Do TOC IL. Do normal play.
When these following key is input
into PLAY key, track number can
be appoint directly.
When these following key is input
into PLAY key, track number can
be appoint directly.
<<PLAY>> key input.
<<MEMORY>> key input.
<<
1>> key: Track 4
<<
2>> key: Track 9
<<
3>> key: Track 15
<<STOP>> key input.
STOP
Laser ON.
<<MEMORY>> key input.
Tracking OFF play at that
specific point.
specific point.
<<MEMORY>> key input.
Tracking ON play from
that specific point.
that specific point.
<<STOP>> key input.
STOP
IL isn't done.
VOL — Last memory.
BAL — CENTER
P.GEQ — FLAT
X-BASS — OFF
BAL — CENTER
P.GEQ — FLAT
X-BASS — OFF
To cancel : Power OFF
Sliding the PICKUP with
<<
<<
>>, <<
>> button
must only be in STOP mode.
<<MEMORY>>
key input.
key input.
Adjustment result
automatically will
display as below
for each 2 sec :
a) "FOFF_XX"
b) "TOFF_XX"
c) "TBAL_XX"
d) "TGAN_XX"
f) "FGAN_XX"
g) "RFLS_XX"
automatically will
display as below
for each 2 sec :
a) "FOFF_XX"
b) "TOFF_XX"
c) "TBAL_XX"
d) "TGAN_XX"
f) "FGAN_XX"
g) "RFLS_XX"
explanation:
a) Focus off set.
a) Focus off set.
="FOFF_XX"
b) Tracking off set.
="TOFF_XX"
c) Tracking balance.
="TBAL_XX"
d) Tracking gain.
="TGAN_XX"
f)
Focus Gain.
="FGAN_XX"
g) RF level shift.
="RFLS_XX"
Adjustment result auto-
matically will display as
below.
for each 2 sec :
a) "FOFF_XX"
b) "TOFF_XX"
c) "TBAL_XX"
d) "TGAN_XX"
f) "FGAN_XX"
g) "RFLS_XX"
matically will display as
below.
for each 2 sec :
a) "FOFF_XX"
b) "TOFF_XX"
c) "TBAL_XX"
d) "TGAN_XX"
f) "FGAN_XX"
g) "RFLS_XX"
XX: Hex value.
CD-BA250H/CD-BA2600H
– 18 –
Standard Specification of Stereo System Error Message Display Contents
Error Contents
DISPLAY
Notes
Output while Device Protection Operation.
'PROTECT'
00: While in Protect Circuit Operate.
01: Over Current Detection.
02: DC Detection.
03:
TAPE
Mechanism Error.
'ER-TA**'
00: Tape Mechanism Error.
01: Initial Error.
02:
03:
CD/VCD
Pickup Mechanism Error.
'ER-CD**'
00: Pickup Mechanism Error.
01: PU-IN SW Detection NG.
02:
03:
04:
CD Changer Mechanism Error.
'ER-CD**'
10: Changer Error.
11: Initial Error.
12:
13:
Tray Error.
'ET-CD**'
20: Tray Error.
21:
22:
23:
Focus Not Match.
'NO DISC'
IL Time Over.
'NOT READ'
TUN
PLL Unlock.
'ER-TU**'
00: TUN Error.
01: PLL Unlock.
02:
03:
CD-BA250H/CD-BA2600H
– 18 –
Standard Specification of Stereo System Error Message Display Contents
Error Contents
DISPLAY
Notes
Output while Device Protection Operation.
'PROTECT'
00: While in Protect Circuit Operate.
01: Over Current Detection.
02: DC Detection.
03:
TAPE
Mechanism Error.
'ER-TA**'
00: Tape Mechanism Error.
01: Initial Error.
02:
03:
CD/VCD
Pickup Mechanism Error.
'ER-CD**'
00: Pickup Mechanism Error.
01: PU-IN SW Detection NG.
02:
03:
04:
CD Changer Mechanism Error.
'ER-CD**'
10: Changer Error.
11: Initial Error.
12:
13:
Tray Error.
'ET-CD**'
20: Tray Error.
21:
22:
23:
Focus Not Match.
'NO DISC'
IL Time Over.
'NOT READ'
TUN
PLL Unlock.
'ER-TU**'
00: TUN Error.
01: PLL Unlock.
02:
03:
CD-BA250H/CD-BA2600H
– 18 –
Standard Specification of Stereo System Error Message Display Contents
Error Contents
DISPLAY
Notes
Output while Device Protection Operation.
'PROTECT'
00: While in Protect Circuit Operate.
01: Over Current Detection.
02: DC Detection.
03:
TAPE
Mechanism Error.
'ER-TA**'
00: Tape Mechanism Error.
01: Initial Error.
02:
03:
CD/VCD
Pickup Mechanism Error.
'ER-CD**'
00: Pickup Mechanism Error.
01: PU-IN SW Detection NG.
02:
03:
04:
CD Changer Mechanism Error.
'ER-CD**'
10: Changer Error.
11: Initial Error.
12:
13:
Tray Error.
'ET-CD**'
20: Tray Error.
21:
22:
23:
Focus Not Match.
'NO DISC'
IL Time Over.
'NOT READ'
TUN
PLL Unlock.
'ER-TU**'
00: TUN Error.
01: PLL Unlock.
02:
03: