Sharp CD-BA1300 User Manual / Operation Manual ▷ View online
28
HOW TO USE THE BUILT-IN TIMER
„
Timer playback
1
Press the ON/STAND-BY button to turn the power
on.
on.
2
Press the CD, TUNER (BAND) or TAPE (1 2) button
to select the desired function, and then adjust the
sound volume using the VOLUME buttons.
to select the desired function, and then adjust the
sound volume using the VOLUME buttons.
3
Press the TIMER/SLEEP button repeatedly until " "
is displayed. At this point, make sure that "REC" is
not lit.
is displayed. At this point, make sure that "REC" is
not lit.
z
The timer set indicator will flash.
4
Press the TUNING/TIME ( or ) button to set the
hour start time, then press the MEMORY/SET button.
hour start time, then press the MEMORY/SET button.
5
Press the TUNING/TIME ( or ) button to set the
minute start time, then press the MEMORY/SET but-
ton.
minute start time, then press the MEMORY/SET but-
ton.
z
The unit will enter the stand-by mode automatically, and
the timer set indicator will light up.
the timer set indicator will light up.
6
When the preset time is reached, the timer playback
will start.
will start.
z
The volume will increase gradually.
7
If you select CD or TAPE, the unit will enter the
stand-by mode after the playback. If you select
TUNER, it will enter the stand-by mode one hour
after the timer playback starts.
stand-by mode after the playback. If you select
TUNER, it will enter the stand-by mode one hour
after the timer playback starts.
Note:
z
Once the time is set, the setting will be retained until a
new time is entered.
new time is entered.
The unit will turn on and play the selected source at the pre-
set time.
set time.
z
Before setting the timer, make sure that the clock setting
is correct (page 8).
is correct (page 8).
(Main unit operation)
TIMER/
SLEEP
Timer set indicator
ON/
STAND-BY
MEMORY/
SET
SET
VOLUME
TUNING/
TIME
( )
TIME
( )
CD
TUNER
(BAND)
TAPE
(1 2)
29
(Continued)
„
Timer recording
1
Press the ON/STAND-BY button to turn the power
on.
on.
z
Load a cassette for recording into the TAPE 2 cassette
compartment.
compartment.
2
Press the TUNER (BAND) button to select the
desired frequency band, and then adjust the sound
volume using the VOLUME buttons.
desired frequency band, and then adjust the sound
volume using the VOLUME buttons.
3
Press the TIMER/SLEEP button repeatedly until " "
and "REC" are displayed.
and "REC" are displayed.
z
The timer set indicator will flash.
4
Press the TUNING/TIME ( or ) button to set the
hour start time, then press the MEMORY/SET button.
hour start time, then press the MEMORY/SET button.
5
Press the TUNING/TIME ( or ) button to set the
minute start time, then press the MEMORY/SET but-
ton.
minute start time, then press the MEMORY/SET but-
ton.
z
The unit will enter the stand-by mode automatically, and
the timer set indicator will light up.
the timer set indicator will light up.
6
When the preset time is reached, the timer recording
will start.
will start.
z
The volume will increase gradually.
7
When the recording tape reaches its end, the timer
recording will end, and the unit will enter the stand-
by mode.
recording will end, and the unit will enter the stand-
by mode.
To cancel timer operation:
Press the ON/STAND-BY button to turn the power on.
Press the ON/STAND-BY button to turn the power on.
To change the programmed contents:
Start again from step 1.
Start again from step 1.
Note:
z
Once the time is set, the setting will be retained until a
new time is entered.
new time is entered.
The unit will turn on and start recording from the radio at the
preset time.
preset time.
z
Before setting the timer, make sure that the clock setting
is correct (page 8).
is correct (page 8).
(Main unit operation)
TIMER/
SLEEP
Timer set indicator
ON/
STAND-BY
MEMORY/
SET
SET
VOLUME
TUNING/
TIME
( )
TIME
( )
TUNER
(BAND)
30
(Continued)
„
Sleep operation
The radio, compact disc and cassette deck can all be turned
off automatically.
off automatically.
1
Play back the desired sound source.
2
Press the TIMER/SLEEP button repeatedly until
"SLEEP" is displayed.
"SLEEP" is displayed.
To change the sleep time:
Whilst the sleep time is displayed, press the TUNING/TIME
( or ) button to adjust the time. (Maximum: 3 hours - Min-
imum: 1 minute) The amount of sleep time can also be
changed during the sleep operation.
Whilst the sleep time is displayed, press the TUNING/TIME
( or ) button to adjust the time. (Maximum: 3 hours - Min-
imum: 1 minute) The amount of sleep time can also be
changed during the sleep operation.
z
3 hours - 5 minutes 5-minute intervals
z
5 minutes - 1 minute 1-minute intervals
3
Press the MEMORY/SET button.
4
The unit will enter the stand-by mode automatically
after the preset sleep time has elapsed.
after the preset sleep time has elapsed.
Note:
z
Once the sleep time is set, it will remain the same dura-
tion until the setting is changed.
tion until the setting is changed.
To confirm the remaining sleep time:
Press the TIMER/SLEEP button.
Press the TIMER/SLEEP button.
To cancel the sleep operation:
Press the ON/STAND-BY button to enter the stand-by
mode.
Press the ON/STAND-BY button to enter the stand-by
mode.
HEADPHONES
Before plugging in or unplugging the headphones, make
sure the volume level is reduced.
sure the volume level is reduced.
Notes:
z
Be sure your headphones have a 3.5 mm (1/8") diameter
plug and are between 16 ohms and 50 ohms impedance.
The recommended impedance is 32 ohms.
plug and are between 16 ohms and 50 ohms impedance.
The recommended impedance is 32 ohms.
z
When headphones are connected, the speakers are dis-
abled automatically. Adjust the VOLUME buttons for the
desired volume.
abled automatically. Adjust the VOLUME buttons for the
desired volume.
(Main unit operation)
TIMER/
SLEEP
MEMORY/
SET
SET
TUNING/
TIME
( )
TIME
( )
31
RESETTING THE MICROCOMPUTER
Reset the microcomputer under the following condi-
tions:
tions:
z
To erase all of the stored memory contents (clock and
timer settings, and tuner and CD presets).
timer settings, and tuner and CD presets).
z
If the display is not correct.
z
If the operation is not correct.
1
Press the ON/STAND-BY button to enter the stand-
by mode.
by mode.
2
Whilst pressing down the / button and the
EQUALIZER/X-BASS/DEMO button, hold down the
ON/STAND-BY button for at least 1 second.
EQUALIZER/X-BASS/DEMO button, hold down the
ON/STAND-BY button for at least 1 second.
z
"CLEAR AL" will appear.
Caution:
z
The operation explained above will erase all data stored
in memory including clock and timer settings, and tuner
and CD presets.
in memory including clock and timer settings, and tuner
and CD presets.
TRANSPORTING THE UNIT
Before you move this product to a new location, pro-
ceed as follows:
ceed as follows:
1
Press the ON/STAND-BY button to turn the power
on.
on.
2
Press the CD button.
3
Press the OPEN/CLOSE button to open the disc tray.
z
Remove all CDs inserted in the unit.
4
Press the OPEN/CLOSE button to close the disc
tray.
tray.
z
Make sure that "NO DISC" is displayed.
5
Press the ON/STAND-BY button to enter the stand-
by mode, and then unplug the AC power lead from
the AC socket.
by mode, and then unplug the AC power lead from
the AC socket.
MAINTENANCE
„
Internal care
z
Dirty heads, capstans or pinch rollers can cause poor
sound and tape jams. Clean these parts with a cotton
swab moistened with commercial head/pinch roller
cleaner or isopropyl alcohol.
sound and tape jams. Clean these parts with a cotton
swab moistened with commercial head/pinch roller
cleaner or isopropyl alcohol.
z
After long use, the deck's heads and capstans may
become magnetised, causing poor sound. Demagnetise
these parts once every 30 hours of playing/recording
time by using a commercial tape head demagnetiser.
Read the demagnetiser's instructions carefully before
use.
become magnetised, causing poor sound. Demagnetise
these parts once every 30 hours of playing/recording
time by using a commercial tape head demagnetiser.
Read the demagnetiser's instructions carefully before
use.
„
External care
z
Periodically wipe the cabinet with a soft cloth and a
diluted soap solution, then wipe with a dry cloth.
diluted soap solution, then wipe with a dry cloth.
z
Do not use chemically treated cleaning cloths or other
chemicals.
chemicals.
EQUALIZER
X-BASS/
DEMO
X-BASS/
DEMO
ON/
STAND-BY
OPEN/
CLOSE
CLOSE
ON/
STAND-BY
CD
TAPE 1
TAPE 2
Click on the first or last page to see other CD-BA1300 service manuals if exist.