Sharp CD-BA1300 User Manual / Operation Manual ▷ View online
24
(Continued)
About the TP and TA indicators
TP indicator
TA indicator
Meaning
Not lit
Not lit
This programme does not carry traffic announcements nor does it
refer, via EON, to a programme that does.
refer, via EON, to a programme that does.
Not lit
Lit
This programme carries EON information about another pro-
gramme which gives traffic information.
gramme which gives traffic information.
Lit
Not lit
This programme carries traffic announcements but none are cur-
rently on air and may also carry EON information about other traffic
announcements.
rently on air and may also carry EON information about other traffic
announcements.
Lit
Lit
A traffic announcement is currently on air on this programme.
In the following cases, the EON stand-by mode will be cancelled.
z
When the unit is set in the stand-by mode.
z
When the unit is switched to another band in the EON stand-by mode.
z
When you change the FM station whilst in the EON stand-by mode.
z
When a preset call is made.
Notes:
z
During the same programme as the specified PTY (or TA) is being broadcast on the station you are receiving, the unit
will not switch to other network station.
will not switch to other network station.
z
If there are more than two other network stations you want to listen to, compare the strength of each station's signal and
tune in the station with the strongest signal. (EON-AF) However, if the frequency of other network station has been stored
in the preset channel memory, the unit will switch to that preset channel.
tune in the station with the strongest signal. (EON-AF) However, if the frequency of other network station has been stored
in the preset channel memory, the unit will switch to that preset channel.
z
To cancel the ON (other network) station tuned in by the EON system and to return to the original station, press the EON
button.
button.
z
After the unit returns to the original station, the stand-by mode will still be active. (The "TI" or "PTY" will remain lit.)
z
The unit will not switch from the ON station to another network station. The unit returns to the original station.
z
When the unit switches automatically to "other network" station, "WEAK SIG" will appear and the unit will return to the
original station if there is any problem with this station or the station cannot be received properly.
original station if there is any problem with this station or the station cannot be received properly.
z
Even if the unit switches from the station you are listening to directly to some "other network" station, the unit will search
for the station with the strongest signal and switch to it if the signals from the other network stations are very weak. How-
ever, if the signals from all the other network stations are very weak, or if the tuning conditions are very bad (due to elec-
trical noise), the unit will stop searching, "WEAK SIG" will be displayed, and the unit will return to the original station you
were receiving.
for the station with the strongest signal and switch to it if the signals from the other network stations are very weak. How-
ever, if the signals from all the other network stations are very weak, or if the tuning conditions are very bad (due to elec-
trical noise), the unit will stop searching, "WEAK SIG" will be displayed, and the unit will return to the original station you
were receiving.
25
CASSETTE OPERATION
„
TAPE 1 or TAPE 2 playback
1
Press the ON/STAND-BY button to turn the power
on.
on.
2
Press the TAPE (1 2) button.
3
Open the cassette door by pushing the area marked
"PUSH EJECT".
"PUSH EJECT".
4
Load the cassette into the TAPE 1 or TAPE 2 cas-
sette compartment.
sette compartment.
5
With cassettes in both decks, press the TAPE (1 2)
button to switch operation from one deck to the
other.
button to switch operation from one deck to the
other.
6
Press the / button to start playback.
z
When playback is performed using the remote control,
press the TAPE 1 or TAPE 2 button.
press the TAPE 1 or TAPE 2 button.
To stop playback:
Press the (TAPE ) button.
Fast forward/rewind: (TAPE 2 only)
1
1
Press the (TAPE ) button, then press the TAPE (1
2) button to select TAPE 2.
2) button to select TAPE 2.
2
To advance the tape, press the
button. To rewind it,
press the
button.
Caution:
z
To remove the cassette tape, press the (TAPE ) but-
ton, and then open the cassette compartment.
ton, and then open the cassette compartment.
z
Before changing from one tape operation to another,
press the (TAPE ) button.
press the (TAPE ) button.
z
If a power failure occurs during tape operation, the tape
head will remain engaged with the tape and the cassette
door will not open. In this case, wait until power is
restored.
head will remain engaged with the tape and the cassette
door will not open. In this case, wait until power is
restored.
TAPE 1
TAPE 2
PUSH
EJECT
PUSH
EJECT
TAPE
1
6
4
3
4
2,5
2,5
6
6
1
3
26
RECORDING
„
Recording from the built-in CD player (CD
Synchronised Recording System)
Synchronised Recording System)
1
Press the ON/STAND-BY button to turn the power
on.
on.
2
Load a cassette into the TAPE 2 cassette compart-
ment.
ment.
3
Press the CD button and load the desired disc.
z
Use the APMS function to store the tracks you want to
record in memory. (See page 12.)
record in memory. (See page 12.)
4
Press the REC PAUSE (
) button.
z
"SYNC" and "REC" will flash.
5
Press the / (TAPE 2 ) button.
z
"SYNC" will disappear and "REC" will light up.
z
CD playback will start approximately 5 seconds after the
tape starts.
tape starts.
To stop recording:
Press the (CD ) button.
The CD and tape will stop.
Press the (CD ) button.
The CD and tape will stop.
Note:
z
When the end of the tape is reached whilst recording, the
CD player will display the track number which was being
played at that time, and stop automatically. If you want to
restart recording from the beginning of the interrupted
track, turn over the tape, press the REC PAUSE (
CD player will display the track number which was being
played at that time, and stop automatically. If you want to
restart recording from the beginning of the interrupted
track, turn over the tape, press the REC PAUSE (
) but-
ton and then the / (TAPE 2 ) button. (If tracks have
been stored in memory using the APMS function, record-
ing will restart from the first track stored in memory.)
been stored in memory using the APMS function, record-
ing will restart from the first track stored in memory.)
„
Recording from the built-in radio
1
Press the ON/STAND-BY button to turn the power
on.
on.
2
Load a cassette into the TAPE 2 cassette compart-
ment.
ment.
3
Tune in to the desired station (pages 14 - 15).
4
Press the REC PAUSE (
) button.
z
"REC" will flash.
5
Press the / (TAPE 2 ) button.
z
"REC" will appear.
To interrupt recording:
1
1
Press the REC PAUSE (
) button.
z
"REC" will flash.
2
Press the / (TAPE 2 ) button to resume recording.
z
"REC" will appear.
To stop recording:
Press the (TAPE ) button.
Press the (TAPE ) button.
Note:
z
If a whistling noise is heard whilst recording from an AM
station, move the AM loop aerial to a position where
noise is no longer heard from the unit.
station, move the AM loop aerial to a position where
noise is no longer heard from the unit.
z
When recording important selections, be sure to make a
preliminary test to ensure that the desired material is be-
ing properly recorded.
preliminary test to ensure that the desired material is be-
ing properly recorded.
z
The volume and sound quality can be adjusted with no
effect on the recorded signal (Variable Sound Monitor).
effect on the recorded signal (Variable Sound Monitor).
z
Metal and CrO tapes should not be used for recording
or dubbing.
or dubbing.
TAPE 2
PUSH
EJECT
TAPE
TAPE 2
CD
ON/
STAND-BY
CD
REC PAUSE
ON/
STAND-BY
CD
27
(Continued)
„
Dubbing from tape to tape
1
Press the ON/STAND-BY button to turn the power
on.
on.
2
Load a prerecorded cassette into the TAPE 1 cas-
sette compartment. Insert a blank tape into the
TAPE 2 cassette compartment.
sette compartment. Insert a blank tape into the
TAPE 2 cassette compartment.
z
It is recommended that the recording tape is the same
length as the master tape.
length as the master tape.
3
Press the TAPE (1 2) button until "TAPE 1"
appears in the display.
appears in the display.
4
Press the REC PAUSE (
) button.
5
Press the / (TAPE 2 ) button.
To stop dubbing:
Press the (TAPE ) button.
Press the (TAPE ) button.
z
TAPE 1 and TAPE 2 will simultaneously stop.
„
Erasing recorded tapes
z
Make sure that TAPE 1 is not in use.
1
Load the tape to be erased into the TAPE 2 cassette
compartment.
compartment.
2
Press the TAPE (1 2) button until "TAPE 2"
appears in the display.
appears in the display.
3
Press the REC PAUSE (
) button.
4
Press the / (TAPE 2 ) button.
TAPE 2
TAPE
ON/
STAND-BY
REC PAUSE
TAPE 1
TAPE 2
PUSH
EJECT
PUSH
EJECT
TAPE
(1 2)
(1 2)
TAPE
(1 2)
(1 2)
ON/
STAND-BY
Click on the first or last page to see other CD-BA1300 service manuals if exist.