Panasonic TX-LR65WT600 Service Manual ▷ View online
Specifications
Power
Source:
220-240V AC, 50 / 60Hz
Rated Power Consumption:
295W
Stand-by Power Consumption: 0.20W
Aerial Impedance: 75
unbalanced, Coaxial Type
Receiving System:
DVB-S/S2 Digital satellite services (
MPEG2 and MPEG4-AVC(H.264)
)
Receiver frequency range:950MHz to2,150MHz
DiSEqC – Version 1.0
DVB-C Digital cable services (
MPEG2 and MPEG4-AVC(H.264)
)
DVB-T /T2 Digital terrestrial services (
MPEG2 and MPEG4-AVC(H.264)
)
PAL D/K,
SECAM
D/K
VHF R1-R2 VHF R3-R5
VHF R6-R12 UHF E21-E69
PAL 525/60 (AV only)
M.NTSC (AV only)
NTSC (AV only)
Satellite dish input:
Female F-type 75
x 2
Aerial - Rear:
VHF/UHF
Operating Conditions:
Temperature: 0°C
35°C
Humidity:
20%
80% RH (non condensing)
Terminals:
AV1 IN
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 10k
RGB (21 pin)
0.7V p-p 75
AV1 OUT
Video (21 pin)
1V p-p 75
Audio (21 pin)
500mV rms 1k
AV2 IN
Video (RCAx1)
1V p-p 75
(COMPONENT/VIDEO)
Audio (RCAx2)
500mV rms 10k
(used for HDMI_ AV2 audio IN)
Video (RCAx3)
Y:1V p-p 75
(including synchronization)
Pb, Pr: ±0.35V p-p 75
HDMI1, HDMI2
Type A Connectors
HDMI3, HDMI4
HDMI
1/3 : 3D, Content Type
HDMI 2 : 3D, Content Type, Audio Return Channel
HDMI4 : 4K, 3D (3D content of 4K format is not supported.), Kontent Type,
Audio Return Channel
This TV supports “HDAVI Control 5” function.
DISPLAY PORT INPUT
VESA DisplayPort (applicable to 4K format)
DIGITAL AUDIO OUT
PCM / Dolby digital / DTS, Fiber optic
USB 1/2/3
USB1/2: DC 5V Max 500mA [Hi-Speed USB (USB 2.0)]
USB3 : DC 5V Max 900mA [SuperSpeed USB (USB 3.0)]
ETHERNET
RJ45, IEEE802.3 10BASE-T / 100BASE-TX
CARD SLOT
SD Card slot x1
Common interface slot (Complies with CI+) x 2
9
Wireless LAN:
Standard Compliance
IEEE802.11a/n , IEEE802.11b/g/n
Frequency Range
IEEE802.11a/n: 5.15 GHz – 5.35 GHz
5.47 GHz – 5.85 GHz
IEEE802.11b/g/n: 2.40 GHz – 2.4835 GHz
Security
WPA2-PSK
(TKIP/AES)
WPA-PSK
(TKIP/AES)
WEP(64
bit/128
bit)
Build-in Camera:
Lens
F2.0 Lens; FOV (D) 50.9° (in HD mode)
Focus
Fixed
focus
Resolution
1,280
x
720
Bluetooth Wireless
technology:
Standard Compliance:
Bluetooth 3.0
Frequency Range
2.402 GHz – 2.480 GHz
3D
Eyewear:
Dimensions (W x H x D)
164.7mm x 41.0m x 170.7mm
Mass
34g
Lens Type
Liquid Crystal Shutter
Usage Temperature Range
0°C
40°C
Battery
Coin-shaped lithium battery CR2025
Operation time: Approx. 75 hours in continuous use of the battery made by Panasonic
Materials
Main
body:
Resin
Lens section: Liguid crystal glass
LCD screen:
L5EDDYY00538
3840 x 2160, 16:9
Visible Diagonal 1640mm
Speaker:
speakers x 2, Woofer x 1
Audio
Output:
18W (4W + 4W + 10W)
Headphones:
3.5mm,
8
Impedance
Accessories supplied :
Remote Control
Touch
Pad
Controller
3D
Glasses
4 x R6 (UM3) Batteries
SCART
Cable
AV
Cable
Dimensions:
Width:
Height: Depth:
Including TV stand
1,468mm 960mm 425mm
TV set only
1,468mm 863mm 56mm
Mass:
Including TV stand
43.0kg
TV set only
38.0kg
Design and Specifications are subject to change without notice. Mass and dimensions shown are approximate.
This equipment complies with the EMC standards listed below:
EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024
10
Technical Description
Specification of KEY for CI Plus, DTCP-IP, One-to-One, Netflix, Widewine and HDCP
General information
General information
1. NAND FLASH (IC8900) for spare parts has the seed of KEY for each.
2. The final KEY data will be generated by Pro4 IC (IC8000) when SELF CHECK was done and are stored in both
Pro4 IC (IC8000) and NAND FLASH (IC8900).
All KEYs are not generated for all models.
The necessary KEY are only generated and stored depend on the feature of models.
2. The final KEY data will be generated by Pro4 IC (IC8000) when SELF CHECK was done and are stored in both
Pro4 IC (IC8000) and NAND FLASH (IC8900).
All KEYs are not generated for all models.
The necessary KEY are only generated and stored depend on the feature of models.
Replacement of ICs
When Pro4 IC (IC8000) is replaced, NAND FLASH (IC8900) should be also replaced with new one the same time.
When NAND FLASH (IC8900) is replaced, Pro4 IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the MENU button on the remote
control for more than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK.
When NAND FLASH (IC8900) is replaced, Pro4 IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the MENU button on the remote
control for more than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK.
Model and Keys
USB HDD Recording
General information
General information
Digital TV programmes can be recorded in USB HDD.
A One-to-One key generated in A-board by SELF CHECK binds TV and USB-HDD for communication.
That key is only one key for them. If the key is difference, TV can not access USB-HDD.
Caution:
New key will be generated by following SELF CHECK and previous TV programmes recorded in USB HDD will not be
viewed.
SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the MENU button on the remote control for more
than 3 seconds.
A One-to-One key generated in A-board by SELF CHECK binds TV and USB-HDD for communication.
That key is only one key for them. If the key is difference, TV can not access USB-HDD.
Caution:
New key will be generated by following SELF CHECK and previous TV programmes recorded in USB HDD will not be
viewed.
SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the MENU button on the remote control for more
than 3 seconds.
Keys
Model No.
CI PLUS
DTCP-IP
One-to-One
(for USB Rec.)
Netflix_PRO4_4K
Widewine
HDCP2
TX-LR65WT600 Yes No
Yes
Yes
Yes
11
Setting Inspection
Voltage Confirmation
A board
Description Test
point
Voltage
STB5.8V
TP2017 / TP5205
5.05V - 5.59V
STB3.3V
TP5002
3.12V – 3.45V
STB1.1V
TP5003
1.08V – 1.20V
SUB9V
TP5004
8.52V – 9.42V
SUB5V
TP5420
4.91V - 5.43V
SUB3.3V
TP5400
3.16V – 3.50V
SUB1.8V
TP8714
1.76V – 1.94V
SUB1.5V
TP8101
1.39V – 1.53V
SUB1.1V
TP8100
1.08V – 1.20V
USB5V
TP5440
4.94V – 5.46V
SD3.3V
TP8671
3.20V – 3.54V
M3.3V
TP8492
3.14V – 3.48V
M1.2V
TP8406
1.14V – 1.26V
HDMI3.3V
TP8701
3.16V – 3.50V
SUB_AI_3.3V
TP2002
3.16V – 3.50V
SAT_2.5V
TP5705
2.37V – 2.63V
SAT_1.2V
TP5703
1.23V – 1.37V
DMD_1.2/1.1V
TP5702
1.11V – 1.23V
FR board
Description Test
point
Voltage
GCX3.3V
TP1800
3.17V – 3.45V
FR3.3V
TP1829
3.20V – 3.51V
HDMI1.1V
TP1802
1.05V – 1.19V
DP1.2V
TP1830
1.10V – 1.28V
FPGA1.0V
TP1803
0.96V – 1.06V
FPGA1.0V_2
TP1808
0.96V – 1.06V
FPGA1.5V
TP1807
1.44V – 1.59V
FPGA1.8V
TP1811
1.71V – 1.90V
FPGA1.2V
TP1804
1.14V – 1.26V
FPGA2.5V
TP1806
2.38V – 2.63V
FPGA1.8V_2
TP1809
1.71V – 1.89V
GCX1.1V
TP9500
1.09V – 1.21V
GCX_2_1.1V
TP9600
1.09V – 1.21V
GCX1.5V
TP9501
1.41V – 1.53V
GCX_2_1.5V
TP9601
1.41V – 1.53V
DP3.3V
TP3512
3.20V – 3.51V
PNL12V
TP1831
11.5V – 12.5V
P board
Description Test
point
Voltage*
Voltage**
24V (PANEL)
TP7409 and GND TP7515,TP7516
<1V
24V ± 1.2V
16V
TP7412 and GND TP7515,TP7516
<1V
16.0V ± 0.8V
5VS
TP7501 and GND TP7515,TP7516
5.25V ± 0.25V
5.25V ± 0.25V
PFC
TP7202 and GND TP7203***
<340V
390V ± 15V
Gate Q7408
CL7439 and GND TP7515,TP7516
<1V
4V
Gate Q7409
CL7433 and GND TP7515,TP7516
<1V
4V
* Connect AC 230V to JK7101 connector
** Connect DC voltage to SUB_ON P2 connector – pin 8 /TP7416/ from switch.
***Beware, for testing of PFC use the GND (TP7203) in Hot area of P board – risk of electric shock!
12
Click on the first or last page to see other TX-LR65WT600 service manuals if exist.