Panasonic TX-LR65WT600 Service Manual ▷ View online
Self Check
How to access
Self-check indication only:
While pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control.
Self-check indication and forced to factory shipment setting:
While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
While pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control.
Self-check indication and forced to factory shipment setting:
While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
How to exit
Switch off the power with the [POWER] button on the main unit.
Display Ref.
No.
Description
P.C.B.
H14TUN TU6708
Tuner
DVB-A/T/T2/C A-Board
H90STBY IC8000
IC
Peaks-Pro4
A-Board
H91MEM2 IC8900
Flash
Memory
A-Board
H30AVSW IC3000
AV
switch
A-Board
H17LAN IC8900
MAC
A-Board
H00FE
IC6800 / IC6831
DVB-T2/T/C Demodulator
A-Board
H00SAT-TU TU6707
Tuner
DVB-S/S2
A-Board
H96ID
IC8900
CI+, One To One
A-Board
H97ID2
IC8900
Netflix, Widewine, HDCP2
A-Board
H45BT
IC8000 / IC8458
N5HZZ0000130
IC Peaks-Pro4 / USB HUB
BT DONGLE
A-Board
BT Dongle
H42WiFi
IC8000 / IC8458
N5HBZ0000101
IC Peaks-Pro4 / USB HUB
WIFI DONGLE
A-Board
Wifi Dongle
H21DSP
IC4900
Audio Amplifier with DSP
A-Board
H52CAMERA N5ZZ00000318
CAMERA
(Skype)
Camera
Module
H36GCX IC9500
IMAGE
PROCESSOR_GCX-1
FR-Board
H37GCX2 IC9600 IMAGE
PROCESSOR_GCX-2
FR-Board
H80HDMISW1
IC3603
HDMI IC SWITCH_MAIN
FR-Board
H81HDMISW2
IC1501
HDMI IC SWITCH_SUB
FR-Board
H39FP4K IC1500
FPGA
FR-Board
H82DP IC3500
DP
SPLITTER FR-Board
If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".
TX-LR65WT600
65
Self Check Complete
H14TUN
OK
H90STBY OK
H91MEM2 OK
H30AVSW OK
H17LAN OK
H00FE OK
H00SAT-TU OK
H96ID OK
H97ID2 OK
H45BT OK
H42WiFi OK
H21DSP OK
H52CAMERA OK
H36GCX OK
H37GCX2 OK
H80HDMISW1 OK
H81HDMISW2 OK
H39FP4K OK
H82DP OK
H91MEM2 OK
H30AVSW OK
H17LAN OK
H00FE OK
H00SAT-TU OK
H96ID OK
H97ID2 OK
H45BT OK
H42WiFi OK
H21DSP OK
H52CAMERA OK
H36GCX OK
H37GCX2 OK
H80HDMISW1 OK
H81HDMISW2 OK
H39FP4K OK
H82DP OK
PEAKS-SOFT 3.006
PEAKS-EEP 01.02.0002
LSI-PACKAGE 0.00d
LSI-RELEASE 1.04
STBY-SOFT 2.00.02
STBY-EEP 1.00.315d
GCX DATA b1010007
CAMERA 1.0055
FP4K DATA 01000019
DP DATA 00412c2a
EMMC DATA 3.001
PEAKS-EEP 01.02.0002
LSI-PACKAGE 0.00d
LSI-RELEASE 1.04
STBY-SOFT 2.00.02
STBY-EEP 1.00.315d
GCX DATA b1010007
CAMERA 1.0055
FP4K DATA 01000019
DP DATA 00412c2a
EMMC DATA 3.001
MODEL ID 0A
03000105
00008000
21
4 sec
Once
Power LED blinking timing chart
1. Subject
Information of LED Flashing timing chart.
2. Contents
When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the
defective block can be identified by number of blinking of the Power LED on the front panel of the unit.
defective block can be identified by number of blinking of the Power LED on the front panel of the unit.
Blinking
times
Blinking timing
Contents
Check point
1
BL_SOS
A BOARD
PANEL
3
IROM SOS
A BOARD
6
FPGA_SOS
FR BOARD
7
SUB3.3V
A BOARD
8
SOS
A BOARD
FR BOARD
PANEL
9
SOUND_SOS
A BOARD
10
GCX/FRC_SOS FR
BOARD
12
BE_SOS
A BOARD
13
EMERGENCY
A BOARD
LCD Panel Test Mode
Purpose:
To find the possible failure point where in LCD Panel or Printed Circuit Board when the abnormal picture is displayed.
How to Enter:
While pressing [VOLUME ( - )] button of the main unit, press [YELLOW] button of the remote control three times.
How to Exit:
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
How to confirm:
If the abnormal picture is displayed, go into LCD Panel test mode to display the several test patterns.
And then, judge by the following method.
Still abnormal picture is displayed: The cause must be in LCD Panel.
Normal picture is displayed: The cause must be in A board.
And then, judge by the following method.
Still abnormal picture is displayed: The cause must be in LCD Panel.
Normal picture is displayed: The cause must be in A board.
Remarks:
The test pattern is created by the circuit in LCD Panel.
In LCD Panel test mode, this test pattern is displayed unaffected by signal processing for RF or input signal.
If the normal picture is displayed, LCD Panel must be okay and the cause of failure must be in A board.
In LCD Panel test mode, this test pattern is displayed unaffected by signal processing for RF or input signal.
If the normal picture is displayed, LCD Panel must be okay and the cause of failure must be in A board.
No Light
Light
22
Adjustment Method
White Balance Adjustment
Equipment
Remarks
1. Remote
controller
2. LCD WB meter Minolta CA-310, 1000, 2000 or equivalent
3. Signal generator with white pattern (100%, 50%)
3. Signal generator with white pattern (100%, 50%)
Procedure
1. Select HDMI1 or any AV analogue input.
2. Connect signal generator with 100% white pattern to HDMI or any analogue
Input.
3. Enter the Service mode.
4. Select [WB-ADJ] by using [1] and [2] key in the remote controller.
5. Check that the color balance (key [7]) and the viewing mode (key [9]) are the
values written in table 1.
6. Adjust the color point (key [+],[-]) to the target color point by using two
parameters of this 3 parameters (R-GAIN , G-GAIN and B-GAIN by key [3],[4]).
One of them must be “80”.
7. Switch signal generator to white pattern 50% .
8. Adjust the color point to the target color point by using two parameters
of these 3 parameters (R-CENT, B-CENT).G-CENT must be “80”.
9. Change to color balance and viewing mode in table 2.
10. Change method of adjustment from 02 to 01 by key [0].
11. Switch signal generator to white pattern 100%.
12. Adjust the color point (key [+], [-]) to the target color point by using two
parameters of these 3 parameters (R-GAIN, G-GAIN and B-GAIN).
One of them must be “80”.
13. Switch signal to white pattern 50%.
14. Adjust the color point to the target color point by using two parameters
of these 3 parameters (R-CENT, B-CENT).G-CENT must be “80”.
15. Change method of adjustment from 01 to 02 by key [0].
After this changing method DO NOT PRESS “OK” BUTTON .
Table1
2. Connect signal generator with 100% white pattern to HDMI or any analogue
Input.
3. Enter the Service mode.
4. Select [WB-ADJ] by using [1] and [2] key in the remote controller.
5. Check that the color balance (key [7]) and the viewing mode (key [9]) are the
values written in table 1.
6. Adjust the color point (key [+],[-]) to the target color point by using two
parameters of this 3 parameters (R-GAIN , G-GAIN and B-GAIN by key [3],[4]).
One of them must be “80”.
7. Switch signal generator to white pattern 50% .
8. Adjust the color point to the target color point by using two parameters
of these 3 parameters (R-CENT, B-CENT).G-CENT must be “80”.
9. Change to color balance and viewing mode in table 2.
10. Change method of adjustment from 02 to 01 by key [0].
11. Switch signal generator to white pattern 100%.
12. Adjust the color point (key [+], [-]) to the target color point by using two
parameters of these 3 parameters (R-GAIN, G-GAIN and B-GAIN).
One of them must be “80”.
13. Switch signal to white pattern 50%.
14. Adjust the color point to the target color point by using two parameters
of these 3 parameters (R-CENT, B-CENT).G-CENT must be “80”.
15. Change method of adjustment from 01 to 02 by key [0].
After this changing method DO NOT PRESS “OK” BUTTON .
Table1
Dynamic-Normal (method 02)
x
y
High-light (100% white)
0.285
0.010
0.293
0.010
Low-light (50% white)
0.285
0.010
0.293
0.010
Table 2
Cinema-Warm (method 01)
x
y
High-light (100% white)
0.313
0.005
0.329
0.005
Low-light (50% white)
0.313
0.005
0.329
0.005
Let the panel stand for more than 3
hours at more than 20
hours at more than 20
C.
Basically perform adjustment in the
ambient environment of room
temperature more than 20
ambient environment of room
temperature more than 20
C.
The aging time is more than 20 min
at above room temperature.
Applied signal
100% white pattern
0.7V p-p white peak
at above room temperature.
Applied signal
100% white pattern
0.7V p-p white peak
23
CI SLOT
main
JK8400
HDMI1
JK4701
SD SLOT
JK8600
A-BOARD
AV scart
JK3002
HDMI2
JK4702
TU6707
A12
SP
A10
K-BOARD
K10
A02
LCD PANEL
P-BOARD
P2
MAIN IN
HP
JK3202
P5
ETHERNET
JK8650A
JK3001
YUV
, V IN
AUDIO IN
RCA
USB1
JK8601
USB3
JK8603
HDMI3
JK4703
Wiring Diagram
JK7101
FR02
A20
WIFI
USB2
JK8602
GK-BOARD
GK4
TU6708
D3201
DIGIT
AL
AUDIO
OUT
FR10
FR1
1
SA
T
TUNER_Main/Sub
TER
TUNER_Main/Sub
BT
A23
Camera Module
A05
LL-BOARD
LL5
A06
LR-BOARD
LR6
FR-BOARD
LA-BOARD
LA5
LB-BOARD
LB6
CI SLOT
sub
JK8401
A40
P3
P4
P6
FR20
FR30
DP
JK3601
HDMI4
JK3502
A15
FR01
A16
Service
CN0100
CN3500
CN1600
SER
VICE
SER
VICE
FR40
CN91
10
SER
VICE
24
Click on the first or last page to see other TX-LR65WT600 service manuals if exist.