Panasonic KX-TGF310RUM / KX-TGF320RUM / KX-TGF320UCM / KX-TGFA30RUM Service Manual ▷ View online
61
KX-TGF310RUM/KX-TGF320RUM/KX-TGF320UCM/KX-TGFA30RUM
11.2.2. Connections (Handset)
Connect the DC Power or Battery to BATT+ and BATT-.
Connect the JIG cable GND (black) to GND.
Connect the JIG cable UTX (yellow) to UTX and URX (red) to URX.
Connect the JIG cable GND (black) to GND.
Connect the JIG cable UTX (yellow) to UTX and URX (red) to URX.
Note:
*: COM port names may vary depending on what your PC calls it.
DC Power
or Battery
2
GND (black)
3
To Serial Port
(com port 1*)
(com port 1*)
JIG Cable
PC
URX (red)
3
UTX (yellow)
Handset P. C. board
1
BATT-
BATT+
GND
UTX
URX
62
KX-TGF310RUM/KX-TGF320RUM/KX-TGF320UCM/KX-TGFA30RUM
11.2.3. How to install Batch file into P.C.
Note:
• “*****” varies depending on the country or models.
1.
Insert the Batch file CD-ROM into CD-ROM drive and
copy PNZZTG**** folder to your PC (example: D drive).
2.
Open an MS-DOS mode window.
3.
At the DOS prompt, type "D:" (for example) to select the
drive, then press the Enter key.
4.
Type "CD
㪳PNZZTG****", then press the Enter key.
5.
Type "SET_COM=X", then press the Enter key
(X: COM port number used for the serial connection on your PC).
6.
Type "READID", then press the Enter key.
䊶If any error messages appear, change the port number or
䇭check the cable connection.
䊶If any value appear, go to next step.
7.
Type "DOSKEY", then press the Enter key.
<Example>
C:
>Documents and Settings>D:
D:
>>CD >PNZZTG****
D:
>PNZZTG**** >SET_COM=X
D:
>PNZZTG****>READID
00 52 4F A8 A8
D:
D:
>PNZZTG****>DOSKEY
D:
>PNZZTG****>
<Example: error happens>
C:
>Documents and Settings>D:
D:
>>CD >PNZZTG****
D:
>PNZZTG**** >SET_COM=X
D:
>PNZZTG****>READID
ޓCreateFile error
ERROR 10: Can't open serial port
D:
ERROR 10: Can't open serial port
D:
>PNZZTG ****>
<Example for Windows>
On your computer, click [Start], select Programs
(All Programs for Windows XP/Windows Server 2003),
then click
MS-DOS Prompt. (for Windows 95/Windows 98)
Or
Accessories-MS-DOS Prompt. (for Windows Me)
Or
Command Prompt. (for Windows NT 4.0)
Or
Accessories-Command Prompt.
(for Windows 2000/Windows XP/Windows Server 2003)
(All Programs for Windows XP/Windows Server 2003),
then click
MS-DOS Prompt. (for Windows 95/Windows 98)
Or
Accessories-MS-DOS Prompt. (for Windows Me)
Or
Command Prompt. (for Windows NT 4.0)
Or
Accessories-Command Prompt.
(for Windows 2000/Windows XP/Windows Server 2003)
63
KX-TGF310RUM/KX-TGF320RUM/KX-TGF320UCM/KX-TGFA30RUM
11.2.4. Commands
See the table below for frequently used commands.
*VES:Vertual EEprom system (adjustment data is stored in program Flash (IC502))
Command name
Function
Example
rdeeprom
Read the data of EEPROM/VES*
Type “rdeeprom 00 00 FF”, and the data from address
“00 00” to “FF” is read out.
“00 00” to “FF” is read out.
readid
Read ID (RFPI)
Type “readid”, and the registered ID is read out.
writeid
Write ID (RFPI)
Type “writeid 00 18 E0 0E 98”, and the ID “0018 E0 0E
98” is written.
98” is written.
hookoff
Off-hook mode on Base
Type “hookoff”.
hookon
On-hook mode on Base
Type “hookon”.
getchk (Base unit)
Read checksum
Type “getchk”.
How to use of
"getchk"
in Handset
"getchk"
in Handset
1.rdeeprom
Read EEPROM/VES*
Type “RdEeprom 03 7D 04”, and the data from address
"03 7D" to "03 80" is read out
*This command gets 4 byte "WW", "XX", "YY", "ZZ".
*Please NEVER forget these 4 byte data!
"03 7D" to "03 80" is read out
*This command gets 4 byte "WW", "XX", "YY", "ZZ".
*Please NEVER forget these 4 byte data!
2.sendchar epw
Write EEPROM/VES*
Type “sendchar epw 03 7D 04 FF FF FF FF”
3.sendchar RST
Reset baseset
Type “sendchar RST”
4.getchk
Read checksum
Type “getchk”.
5.sendchar epw
Write EEPROM/VES*
Type “sendchar epw 03 7D 04 WW XX YY ZZ”
*"WW", "XX", "YY", "ZZ" is 4 byte data that already read
from same address.
*"WW", "XX", "YY", "ZZ" is 4 byte data that already read
from same address.
wreeprom
Write the data of EEPROM/VES*
Type “wreeprom 01 23 45”. “01 23” is address and “45”
is data to be written.
is data to be written.
bursttx
Burst TX mode
Type “bursttx”
testrx
Burst RX mode
Type “testrx”
tph
Keep TX power high
Type"tph"
tpl
Keep TX power low
Type"tpl"
64
KX-TGF310RUM/KX-TGF320RUM/KX-TGF320UCM/KX-TGFA30RUM
11.3. Adjustment Standard (Base Unit)
When connecting the simulator equipment for checking, please refer to below.
11.3.1. Bottom View
Note:
(*2) refers to Power Supply Circuit/Reset Circuit (P.13)
Frequency Counter (*1)
Oscilloscope (*2)
Send command "SFR", then
the frequency output on this TP.
the frequency output on this TP.
STM/CKM/P15
PC
UART
JIG
BATT+
BATT-
BT_MDO
Q681
C601
ANT-S-BT-GND
RA501
R451
STM/P15
C611
TP_FLG
F301
F302
R658
SPN
SPP
C431
C432
C433
C434
C435
C436
C437
R474
C438
R475
C439
R477
R478
C440
C441
C442
C443
BT_1.8V
R681
C451
R682
C457
C458
ANT1-S-GND
Q301
Q302
Q303
Q304
BT_GND
CN671
Q305
Q306
BT_SIO
Q308
Q309
URX
C472
C473
C474
C475
C477
C478
ANT1_TP
C677
UTX
Q331
IC601
Q145
D431
D432
D433
D434
L331
IC611
Q731
Q732
Q161
R101
R102
R103
R104
R109
R301
R302
R303
R304
R305
R111
R306
R112
R307
R308 R309
R115
R116
BT_SOT
D472
D473
R320
ANT2_TP
R321
R322
R323
R324
R331
R332
R333
C103
C104
C105
R142
C106
R143
R144
R145
C109
VDD1
R146
R147
VDD3
R148
VDD4
R149
VDD5
C301
VDD6
C302
C303
C304
C111
C113
BT_TCK
R150
R151
C115
R152
C116
C501
R731
R732
R733 R734
BT_URX
ANT_TP-BT
R735
HS-MICM
C505
R160
C319
R162
R163
BT_TDO
R164
R165
R166
R167
R168
C320
R169
C322
C517
C518
Batt_PW_EN
R170
+5.5V
RA611
BT_UTX
C331
C332
C333
ANT1-Short
C141
C143
C721
C722
C723
RA431
RA432
C152
HS-SPM
HS-SPP
2
6
1
C
1
6
1
C
C164
C166
C167
RA451
D301
RA452
D302
BATT
C171
C173
ANT-Short-BT
C184
CKM
IC302
IC304
D132
D133
IC502
HS-MICP
L431
L432
L433
L434
BT_TMS
IC722
GND
R661
R504
R551
Q142
Q144
R117 R118
BT_UTX
BT_URX
VDD1
STM/P15
VDD5
VDD4
VDD3
DCM
DCP
GND
UTX
URX
L1R
L1T
L1R
L1T
ANT_1
Spectrum
Analyzer
SP-
SP+
HS_SPP
HS_SPM HS_MICP
HS_MICM
ANT_BT
Spectrum
Analyzer
Analyzer
DC
5.5V
VDD6
BATT
BATT+
REF-1
PNLB2420Z*
KX-TGF38x/35x
KX-TGF32x/31x
KX-TGF32x/31x
A
PbF
Click on the first or last page to see other KX-TGF310RUM / KX-TGF320RUM / KX-TGF320UCM / KX-TGFA30RUM service manuals if exist.