Panasonic KX-TCD586RUS / KX-TCA158RUS Service Manual ▷ View online
1.2. How to recognize that Pb Free solder is used
1.2.1. Base Unit PCB
PbF
IC8
IC4
IC6
IC3
IC2
C103
1
1
1
22
44
23
1
8
4
5
38
65
102
103
128
64
39
11
28
18
Marked
(Component View)
PbF
TP17
TP11
TP15
JTAG
TP14
TP12
TP5
TP4
1
1
10
3
5
2
4
6
TP7
TP9
TP29
TP24
TP22
TP19
TP21
TP20
GND
UTX
URX
DC_IN
CHARGE
CHARGE
Marked
(Flow Solder Side View)
Note:
The location of the “PbF” marks is subject to change without notice.
5
KX-TCD586RUS / KX-TCA158RUS
1.2.2. Handset PCB
PbF
Marked
IC201
20
1
21
40
41
60
61
80
IC401
IC301
IC303
IC601
IC302
(Component View)
SW40
SW11
SW01
SW1
SW21
SW51
SW53
SW03
SW52
SW02
SW12
SW13
SW33
SW43
SW42
SW31
SW2
SW41
SW32
SW22
SW23
PbF
Marked
(Flow Solder Side View)
Note:
The location of the “PbF” marks is subject to change without notice.
1.2.3. Charger Unit PCB
(Component View)
CN601
3
IC602
1
4
5
L601
Marked
PbF
Note:
The location of the “PbF” marks is subject to change without notice.
6
KX-TCD586RUS / KX-TCA158RUS
2 FOR SERVICE TECHNICIANS
ICs and LSIs are vulnerable to static electricity.
When repairing, the following precautions will help prevent recurring malfunctions.
1. Cover the plastic parts boxes with aluminum foil.
2. Ground the soldering irons.
3. Use a conductive mat on the worktable.
4. Do not touch IC or LSI pins with bare fingers.
3 CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer.
manufacturer.
Dispose of used batteries according to the manufacture’s Instructions.
7
KX-TCD586RUS / KX-TCA158RUS
4 BATTERY
4.1. Battery Installation
Note:
·
Use only a rechargeable battery N4HHGMB00007 or HHR-P103.
4.2. Battery Charge
Place the handset on the charger for about 5.5 hours before initial use. The charge indicator turns red while the battery
is charging, and turns green when the battery is fully charged. When charging, the battery icon is shown as follows.
is charging, and turns green when the battery is fully charged. When charging, the battery icon is shown as follows.
Note:
·
Clean the charge contacts of the handset and charger with a soft, dry cloth, otherwise the battery may not charge properly.
Clean if the unit is exposed to grease, dust or high humidity.
Clean if the unit is exposed to grease, dust or high humidity.
·
If the handset is turned off, it will be turned on automatically when it is placed on the charger.
Note for Service:
·
The battery strength may not be indicated correctly if the battery is disconnected and connected again, even after it is fully
charged.
charged.
·
In that case, by recharging the battery as mentioned above, you will get a correct indication of the battery strength.
8
KX-TCD586RUS / KX-TCA158RUS
Click on the first or last page to see other KX-TCD586RUS / KX-TCA158RUS service manuals if exist.