Panasonic KX-TCD500RUN / KX-TCA150RUN Service Manual ▷ View online
1.2. How to recognize that Pb Free solder is used
(Example: Handset P.C.B.)
IC3
IC2
IC1
IC10
PbF
Marked
(Component View)
Note:
The location of the “PbF“ mark is subject to change without notice.
5
KX-TCD500RUN / KX-TCA150RUN
2 FOR SERVICE TECHNICIANS
ICs and LSIs are vulnerable to static electricity.
When repairing, the following precautions will help prevent recurring malfunctions.
1. Cover the plastic parts boxes with aluminum foil.
2. Ground the soldering irons.
3. Use a conductive mat on the worktable.
4. Do not touch IC or LSI pins with bare fingers.
3 CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer.
manufacturer.
Dispose of used batteries according to the manufacture’s Instructions.
6
KX-TCD500RUN / KX-TCA150RUN
4 BATTERY
4.1. Battery Installation
Please ensure the batteries are inserted as shown.
part should be inserted first.
Close the cover as indicated by the arrow.
•
When you replace the batteries,
part should be removed first.
4.2. Battery Charge
At the time of shipment, the batteries are not charged. To charge, place the handset on the base unit.
Please charge the batteries for about 7 hours before initial use. During charging, the charge LED will light as shown below.
The handset which power is off will be turned on automatically when it is placed on the base unit.
The handset will not operate while it is on the base unit.
If you do not recharge the handset battery for more than 15 minutes, the display will flash
when the handset is lifted off
the base unit.
Note for Service:
•
The battery strength may not be indicated correctly if the battery is disconnected and connected again, even after it is fully
charged.
charged.
In that case, by recharging the battery as mentioned above, you will get a correct indication of the battery strength.
•
Confirmation of Antenna Pict (
) indication:
If Antenna Pict is indicated, charge time is about 7 hours.
However, if Antenna Pict is flashing, charge time becomes long.
7
KX-TCD500RUN / KX-TCA150RUN
4.3. Battery Information
After your Panasonic battery is fully charged:
Ni-MH Batteries (typical 700 mAh)
Operation
Operating Time
While in use (TALK)
10 hrs approx.
While not in use (Standby)
120 hrs approx.
Ni-Cd Batteries (typical 250 mAh)
Operation
Operating Time
While in use (TALK)
4 hrs approx.
While not in use (Standby)
40 hrs approx.
•
Times indicated are for peak performance.
•
The battery operating time may be shortened depending on usage conditions and ambient temperature.
•
Clean the charge contacts of the handset and the base unit with a soft, dry cloth. Clean if the unit is subject to grease,
dust or high humidity.
dust or high humidity.
Otherwise the battery may not charge properly.
•
The batteries cannot be overcharged unless they are repeatedly removed and replaced.
•
For maximum battery life, it is recommended that the handset not be recharged until the battery icon flashes
.
4.4. Replacing the Batteries
If the
icon flashes after a few telephone calls even when the handset batteries have been fully charged, both batteries
must be replaced.
•
Charge new batteries for approximately 7 hours before initial use.
(The telephone line cord must not be connected to the telephone socket at this time).
•
When replacing the batteries, be sure to set up the battery type even if you install the same type of batteries to
initialise battery remaining memory of your handset.
initialise battery remaining memory of your handset.
•
The factory preset is
.
•
To exit the operation, press
any time.
•
Do not use non-rechargeable batteries. If non-rechargeable batteries are fitted and start charging, it may cause the leakage
of the battery electrolyte.
of the battery electrolyte.
•
Press the notch on the cover firmly and slide it as indicated by the arrow. Replace both batteries and close the cover then
charge the handset for about 7 hours.
charge the handset for about 7 hours.
Please order Panasonic P03P(Ni-MH) or P03H(Ni-Cd) batteries.
Note for Service:
•
When Ni-Cd batteies are littled with the
setting in
,
icon might disappear and stop charging
even if the handset is on the cradle for avoiding overcharge.
8
KX-TCD500RUN / KX-TCA150RUN
Click on the first or last page to see other KX-TCD500RUN / KX-TCA150RUN service manuals if exist.