Panasonic KX-TCD156RUB / KX-TCD156RUW / KX-TCA115RUB / KX-TCA115RUW Service Manual ▷ View online
17 CIRCUIT OPERATION (HANDSET)
17.1. Outline
Handset consists of the following ICs as shown in BLOCK DIAGRAM (HANDSET) (P.44).
•
DECT BBIC (Base Band IC): IC1
−
All data signals (forming/analyzing ACK or CMD signal)
−
All interfaces (ex: Key, Detector Circuit, Charge, DC/DC Converter, EEPROM, LCD)
•
RF Module: IC3
−
PLL Oscillator
−
Detector
−
Compress/Expander
−
Amplifier for transmission and reception
•
EEPROM: IC2
−
Temporary operating parameters (for RF, etc.)
17.2. Power Supply Circuit/Reset Circuit
Circuit Operation:
When power on the Handset, the voltage is as follows;
BATTERY(2.2 V ~ 2.6V: TP3)
→
TP14(4V)
→
IC3(6, 25), D3
→
IC1(37)
→
IC1(39, 63) (2.65V)
The Reset signal generates R19, C23 and 2.65V.
17.3. Charge Circuit
Circuit Operation:
When charging the handset on the Base Unit, the charge current is as follows;
DC+(5.5V ~ 6V)
→
D4
→
R43, R44
→
CHARGE+(Base)
→
CHARGE+(Handset)
→
L4
→
Q2
→
F1
→
BATTERY+... Battery...
BATTERY-
→
R21
→
GND
→
L5
→
CHARGE-(Handset)
→
CHARGE-(Base)
→
GND
→
DC-(GND)
In this way, the BBIC on Handset detects the fact that the battery is charged.
The charge current is controlled by switching Q2 of Handset.
Refer to Fig.101 in Power Supply Circuit (P.42).
17.4. Battery Low/Power Down Detector
Circuit Operation:
“Battery Low” and “Power Down” are detected by BBIC which check the voltage from battery.
The detected voltage is as follows;
•
Battery Low
Battery voltage: V(Batt) < 2.3V
The BBIC detects this level and "
" starts flashing and “battery alarm” starts ringing.
•
Power Down
Battery voltage: V(Batt) < 2.2V
The BBIC detects this level and power down.
45
KX-TCD156RUB / KX-TCD156R UW / KX-TCA115RUB / KX-TCA115RUW
18 SIGNAL ROUTE
46
KX-TCD156RUB / KX-TCD156R UW / KX-TCA115RUB / KX-TCA115RUW
19 CPU DATA (BASE UNIT)
19.1. IC2 (BBIC)
Pin
Description
I/O
Hi
Hi-z
Low
Remarks
1
VDD
-
-
-
-
-
2
VSS
-
-
-
-
-
3
PA_Driver_Amp
D.O
PA_ON
-
PA_OFF
-
4
TX/RX SW
D.O
TX
-
RX
-
5
RX_Data
D.I
Data
-
Data
-
6
PLL_Strobe
D.O
Latch
-
Normal
-
7
PLL_Data
D.O
-
-
-
-
8
PLL_Clk
D.O
-
-
-
-
9
TX_Data
D.O
-
-
-
-
10
(NO USE)
D.O
-
-
-
-
11
RF_System_Clk
D.O
-
-
-
-
12
VDD
-
-
-
-
-
13
VSS
-
-
-
-
-
14
RESETQ
A.I
Normal
-
Reset
-
15
VDDPM
D.O
-
-
-
-
16
VSSO
D.I
-
-
-
-
17
LOAD
A.I
-
-
-
-
18
XTAL
A.I
-
-
-
10.368 MHz
19
VDDLR
A.I
-
-
-
-
20
LRB
A.I
-
-
-
-
21
VDDA
-
-
-
-
-
22
VSSA
-
-
-
-
-
23
Audio_Out_N
A.O
-
-
-
-
24
Audio_Out_P
A.O
-
-
-
-
25
Bandgap_Ref
A.I
-
-
-
-
26
Differential_Line_P
A.I
-
-
-
for Bell Clip
27
Differential_Line_N
A.I
-
-
-
for Bell Clip
28
Audio_In_N
A.I
-
-
-
-
29
ADC_Ref
A.I
-
-
-
-
30
RSSI
A.I
-
-
-
-
31
AD2(MPCINP)
A.I
-
-
-
for Polarity
32
AD3
A.I
-
-
-
for Polarity
33
(NO USE)
D.I
(I_PU)
-
-
-
34
(NO USE)
D.I
(I_PU)
-
-
-
35
(NO USE)
D.I
(I_PU)
-
-
-
36
(NO USE)
D.I
(I_PU)
-
-
-
37
VDD
-
-
-
-
-
38
VSS
-
-
-
-
-
39
Supply_EEP
D.O
(Fixed)
-
-
-
40
Serial_Data(I2C)
D.I/O
-
-
-
-
41
Serial_Clk(I2C)
D.O
-
-
-
-
42
MODE
D.I
-
-
(Fixed)
-
43
(NO USE)
D.O
-
-
(Fixed)
-
44
BELL/PAGING
D.O
RINGER_ON
-
RINGER_OFF
-
45
VBACK
A.I
-
-
-
-
46
(NO USE)
-
-
-
(I_PD)
-
47
(NO USE)
D.I
-
-
(Fixed)
-
48
VDD
-
-
-
-
-
49
(NO USE)
D.I
-
-
(Fixed)
-
50
(NO USE)
D.I
(Fixed)
-
-
-
51
(NO USE)
D.I
-
-
(Fixed)
-
52
(NO USE)
D.I
-
-
(Fixed)
-
53
VSS
-
-
-
-
-
54
VDD
-
-
-
-
-
55
KEY_IN
D.I
No Key
-
Key
-
56
(NO USE)
D.I/O
-
-
(I_PD)
-
57
PULSE_CTRL
D.I/O
Q7_ON
-
Q7_OFF
-
58
(NO USE)
D.I/O
-
-
(I_PD)
-
59
(NO USE)
D.I/O
-
-
(I_PD)
-
60
(NO USE)
D.I/O
-
-
(I_PD)
-
61
HOOK_CTRL
D.O
Make
-
Break
-
62
ClipImp_CTRL
D.I/O
Q11_ON
-
Q11_OFF
-
47
KX-TCD156RUB / KX-TCD156R UW / KX-TCA115RUB / KX-TCA115RUW
Pin
Description
I/O
Hi
Hi-z
Low
Remarks
63
ANT1
D.O
ANT1_ON
-
ANT1_OFF
-
64
ANT2
D.O
ANT2_ON
-
ANT2_OFF
-
Note:
I_PU; Internal Pull-Up, I_PD; Internal Pull-Down
20 CPU DATA (HANDSET)
20.1. IC1 (BBIC)
Pin
Description
I/O
Hi
Hi-z
Low
Remarks
1
LCD_SEGMENT
D.O
-
-
-
-
2
LCD_COMMON
D.O
-
-
-
-
3
VDD
-
-
-
-
-
4
VSS
-
-
-
-
-
5
LCD_COMMON
D.O
-
-
-
-
6
LCD_COMMON
D.O
-
-
-
-
7
LCD_COMMON
D.O
-
-
-
-
8
LCD_COMMON
D.O
-
-
-
-
9
LCD_COMMON
D.O
-
-
-
-
10
PA_SW
D.O
PA ON
-
PA OFF
-
11
T/R SW
D.O
Transmit
-
Recieve
-
12
RX_DATA
D.I
-
-
-
-
13
SYEN
D.O
-
-
-
-
14
SYDA
D.O
-
-
-
-
15
SYCL
D.O
-
-
-
-
16
TX_DATA
A.O
-
-
-
-
17
KEY_IN
D.I
No Key
-
Key_In
-
18
KEY_IN
D.I
No Key
-
Key_In
-
19
KEY_IN
D.I
No Key
-
Key_In
-
20
KEY_IN
D.I
No Key
-
Key_In
-
21
KEY_IN
D.I
No Key
-
Key_In
-
22
(NO USE)
D.O
-
-
-
-
23
Reference clock
D.O
-
-
-
-
24
VDD
-
-
-
-
-
25
VSS
-
-
-
-
-
26
POWER_SW
A.I
SW OFF
-
SW_ON
-
27
CHARGE_DET
A.I
Charge
-
No_charge
-
28
DCDCDRV
D.O
-
-
-
-
29
DCDCCMR
A.I
-
-
-
-
30
RESET
A.I
Non Active
-
Active
-
31
VSSO
-
-
-
-
-
32
LOAD
A.I
-
-
-
-
33
XTAL
A.I
-
-
-
-
34
VDDPM
A.O
-
-
-
-
35
VDDLO
A.O
-
-
-
-
36
VDDBAT
A.I
-
-
-
-
37
VDDLR
-
-
-
-
-
38
CHARGE_START
A.O
-
-
-
for charge
39
VDDA
-
-
-
-
-
40
VSSA
-
-
-
-
-
41
LSRN
A.O
-
-
-
-
42
LSRP
A.O
-
-
-
-
43
BANDGAP_REF
A.O
-
-
-
-
44
MICS
A.O
-
-
-
-
45
MICP
A.I
-
-
-
-
46
MICN
A.I
-
-
-
-
47
Reference Voltage
A.O
-
-
-
-
48
RSSI
A.I
-
-
-
-
49
P0.4
D.I
-
-
-
-
50
AD4N
A.I
-
-
-
-
51
AD4P
A.I
-
-
-
-
52
(NO USE)
D.I
-
-
-
-
53
KEY_STRB
D.O
Active
-
-
-
54
KEY_STRB
D.O
Active
-
Non_Active
-
55
KEY_STRB
D.O
Active
-
Non_Active
-
48
KX-TCD156RUB / KX-TCD156R UW / KX-TCA115RUB / KX-TCA115RUW
Click on the first or last page to see other KX-TCD156RUB / KX-TCD156RUW / KX-TCA115RUB / KX-TCA115RUW service manuals if exist.