Panasonic KX-TCD156RUB / KX-TCD156RUW / KX-TCA115RUB / KX-TCA115RUW Service Manual ▷ View online
Items
Adjustment
Point
Procedure
Check or
Replace Parts
(O)*
Receive Audio Check
and Confirmation
TP15
1.
Configure the DECT tester (CMD60) as follows;
<Setting>
•
Test mode: PP
•
Mode: Normal
•
RFPI: 0102030405
2.
Execute the command “testmode”.
3.
Execute the command “regcmd60”
4.
Initiate connection from DECT tester.
5.
Execute the command “openaudio”.
6.
Confirm that the value of EEPROM address “F3F” is “02”. (If the value is not
“02 (by User)”, set “02” and power off and power on, and return to clause 2.)
“02 (by User)”, set “02” and power off and power on, and return to clause 2.)
7.
Input audio signal (50mVrms/1kHz tone) from DECT tester.
<DECT tester setting>
•
Scramble: On
•
AF Gen. to ADPCM: On
•
AF Meter Input: AF Voltm
•
AF Gen. Frequency: 1000Hz
•
AF Gen. Level: 50mVrms
8.
Confirm hearing tone: 300mVrms ± 250mVrms (Just check Audio path)
9.
Confirm that the audio distortion with DECT tester is < 5%.
IC1,C67,C68,
R17,R20,
D7,D6,IC3,
C54,C66,
C60,L3,C57,
C55,C56,
C62,R23,R24,
C63,C64,
C65,R18
(P)
Transmit Audio Check
and Confirmation
TP15
1.
Configure the DECT tester (CMD60) as follows;
<Setting>
•
Test mode: FP
•
Mode: Normal
•
RFPI: 0102030405
2.
Execute the command “testmode”.
3.
Execute the command “regcmd60”.
4.
Initiate connection from DECT tester.
5.
Execute the command “openaudio”.
6.
Confirm that the value of EEPROM address “F3F” is “02”. (If the value is not
“02 (by User)”, set “02” and power off and power on, and return to clause 2.)
“02 (by User)”, set “02” and power off and power on, and return to clause 2.)
7.
Input audio signal (30mVrms/1kHz tone) to DECT tester.
<DECT tester setting>
•
Scramble: On
•
AF Gen. to ADPCM: Off
•
AF Meter Input: ADPCM
•
AF Gen. Frequency: 1000Hz
•
AF Gen. Level: 30mVrms
8.
Confirm hearing tone: 300mVrms ± 250mVrms (Just check Audio path)
9.
Confirm that the audio distortion with DECT tester is < 5%.
IC1,C8,R7,
R8,C6,
C7,C5,R5,
R1,C4,
IC3,C54,C66,
C60,L3,
C57,C55,C56,
C62,R23,
R24,C63,C64,
C65,R18
(Q)
Audio Check and
Confirmation
-
1.
Link to BASE which is connected to Line Simulator.
2.
Set line voltage to 48V and line current to 40mA.
3.
Input -45dBm/1KHz to MIC and measure Line output level.
4.
Confirm that the level is -9 ± 2dBm and that the distortion level is < 5% at TEL
Line (600
Line (600
Ω
Load).
5.
Input -20dBm/1KHz to Line I/F and measure Receiving level at SP+ and SP-.
6.
Confirm that the level is -23 ± 2dBm and that the distortion level is < 5% at
Receiver. (vol = middle, 150
Receiver. (vol = middle, 150
Ω
Load)
33
KX-TCD156RUB / KX-TCD156R UW / KX-TCA115RUB / KX-TCA115RUW
9.2.1. Preparation
9.2. The Setting Method of JIG (Handset)
9.2.1.1. Equipment Required
•
DECT tester: Rohde & Schwarz, CMD 60 is recommended.
•
Frequency counter: it must be precise to be able to measure 1Hz (precision; ± 4ppm).
Hewlett Packard, 53131A is recommended.
•
DC power: it must be able to output at least 1A current under 2.4V for Handset, 9V for JIG.
•
Digital multi-meter (DMM): it must be able to measure voltage and current.
•
Oscilloscope
9.2.1.2. JIGs and PC
•
EEPROM serial JIGs
1. I2C PCB: PQZZTCD420BX
2. RS232C cable: PQZZ1CD705BX
3. Clip cable: PQZZ2CD705BX
4. DC cable: PQZZ3CD705BX
•
PC which runs in DOS mode.
•
Batch file CD-ROM for setting: PQZZTCD156RU
9.2.2. PC Setting
9.2.2.1. Connections
1. Connect the DC Power or Battery to TP3 and TP4 (Handset).
2. Connect the RS232C cable to the Serial Port of PC.
3. Connect the DC cable to the DC Power.
4. Connect the Clip cable GND.
5. Connect the Clip cable SCL and SDA.
Note:
*: Com port names may vary depending on what your PC calls it .
34
KX-TCD156RUB / KX-TCD156R UW / KX-TCA115RUB / KX-TCA115RUW
9.2.2.2. PC Setting
1. Open a window of MS-DOS mode from the start-up menu.
2. Change a directory to the one with “RTX_COM” contained.
3. Type “SET RTX_COM=1” from the keyboard (when COM port 1 is used for the connection).
4. Type “doskey”.
Note:
See the table below for frequently used commands.
Command name
Function
Example
rdeeprom
Read the data of EEPROM
Type “rdeeprom 00 00 FF”, and the data from
address “00 00” to “FF” is read out.
address “00 00” to “FF” is read out.
readid
Read ID (RFPI)
Type “readid”, and the registered ID is read out.
writeid
Write ID (RFPI)
Type “writeid 00 18 E0 0E 98”, and the ID “0018 E0 0E
98” is written.
98” is written.
setfreq
adjust Frequency of RFIC
Type “setfreq nn nn”.
Getchk
Read checksum
Type “getchk”.
Wreeprom
write eeprom
Type “wreeprom 01 23 45". “01 23" is address and “45”
is data to be written.
is data to be written.
35
KX-TCD156RUB / KX-TCD156R UW / KX-TCA115RUB / KX-TCA115RUW
9.3. Adjustment Standard (Handset)
When connecting the Simulator Equipments for checking, please refer to below.
C54
R24
C69
L6
R23
TP19
C63
L7
C66
C62
L3
C65
PbF
SP
SP
C2
L2
D7
D3
D1
D5
R11
R16
C22
C30
C8
C3
C26
C28
C29
C6
R8
D2
D4
C16
R12
C17
R22
Q3
Q2
R4
C7
C4
C5
C33
MIC
TP20
TP21
TP3
TP4
R5
R7
R1
D6
R20
C67
R17
C68
R2
R3
C21
C25
R19
IC1
IC2
F1
5
8
4
1
R18
C27
TP18
C20
C23
C18
L5
L4
R21
R6
C24
X1
Q1
C14
TP1
TP2
BAT
TP12
TP16
TP23
TP13
TP17
TP14
TP22
TP10
GND
SCL
SDA
C57
C64
C58
R27
L59
C59
26
A
C56
R26
R25
C61
C71
C70
10
17
1
IC3
C60
C15
PQUP11176W
KX-TCD150R
KX-TCA115
for
50
51
30
31
100
1
81
80
AF
OSC
OSC
AF VOLT
METER
METER
LOOP
Simulator
Simulator
Dummy Base
Unit
Unit
600
OSC
TP20
CHARGE
CHARGE
Genelator
MIC+
+
MIC-
AF
6.3V47 F
DC
6V
6V
Current
Probe
Probe
Oscilloscope
CHARGE-
TP21
TP21
DC POWER
2.30 - 2.60V
2.30 - 2.60V
2.7V/2W
BATTERY
BATTERY-
TP4
TP3
PC
(*1)
I2C PCB
(JIG)
SDA
SDL
GND
Digital
Volt Meter
Volt Meter
GND
TP18
150
AF
Volt Meter
Volt Meter
Frequency
Counter
Counter
SP-
SP+
GND
TP19
Digital
Volt Meter
Volt Meter
Oscilloscope
Oscilloscope
GND TP14
TP17
Power Key
TP16
DECT tester
CMD60
CMD60
GND
ANT
(F) (G)
(A)
(I) (J) (K) (L) (M)
(N) (O) (P)
(N) (O) (P)
(H)
(B)
(C) (E) (F) (H)
(I) (O) (P)
(I) (O) (P)
(D)
(D)
(D) (E)
A (201)
TP15
TP15
Note:
(A) - (P) is referred to Check Point (Handset) (P.31)
(*1) Refer to Connections (P.34)
KX
-T
CD1
56RUB
/
K
X
-T
C
D156R
UW
/
K
X
-T
C
A115R
UB
/
K
X
-T
CA1
15RUW
36
Click on the first or last page to see other KX-TCD156RUB / KX-TCD156RUW / KX-TCA115RUB / KX-TCA115RUW service manuals if exist.