Panasonic AG-HVX200P / AG-HVX200AN / AG-HVX200E / AG-HVX200MC / AG-HVX202EN Service Manual ▷ View online
INF-15
7-2-7. MECHANISM Ass`y
When MECHA I/F Board is exchanged, it requires same operation.
LISTA Sensitivity Detection
LISTA Linearity Adjustment
START
END
Confirmation of Tape Path
Self-REC/PLAY ENV Confirmation
LISTA Connection & Boot Up
MECHANISM Ass`y is exchanged.
Tape Path Adjustment is required.
Refer to Mechanical Adjustment Procedure.
Refer to Mechanical Adjustment Procedure.
Overall check
VTR Adjustment is required.
Regarding required adjustment items, refer to item
“7-3. Adjustment after replacement of major Parts”. ( Page INF-16)
Regarding required adjustment items, refer to item
“7-3. Adjustment after replacement of major Parts”. ( Page INF-16)
INF-16
7-3. Adjustment after replacement of major parts
If one of the Major part listed requires replacement, the table below indicates what electrical adjustments are
required.
7-3-1. CAMERA Adjustment
CAMERA LENS Ass`y
ADJUSTMENT ITEM
CAMERA
Board
LENS
Ass`y
Ass`y
PRISM
Ass`y
ZOOM
MOTOR
Ass`y
ZOOM
SW
Ass`y
SIDE
JACK1
Board
Zoom SW Center Value
X
X
Hall Amp (Auto)
X
X
Iris PWM (Auto)
X
X
OIS (Auto)
X
X
Zoom Tracking (Auto)
X
X
X
CCD White scratch damage revision
X
X
Preparation of White Balance
X
X
White Balance (3100K) (Auto)
X
X
White Balance (5100K) (Auto)
X
X
White Balance (4500K) (Auto)
X
X
White Balance (3600K) (Auto) *NOTE
X
X
White Shading (Auto)
X
X
Sync Level
X
!
Y Level
X
!
Pb Level
X
!
Pr Level
X
!
Luminance Level
X
!
Chroma Level
X
!
SETUP *NOTE
X
X: Adjustment Required
!
: Confirmation Required
*NOTE:
White Balance (3600K) and
SETUP adjustment is required only for NTSC model.
7-3-2. VTR Adjustment
ADJUSTMENT ITEM
VTR Board
MECHANIZM
Ass`y
MECHA IF
Board
Sensitivity adj of Tape sensor
X
X
X
PG Shifter
X
X
X
X: Adjustment Required
NOTE:
When the adjustment data backed up is written in a new board when VTR board is exchanged, the adjustment is
unnecessary.
INF-17
8. Service menu
The DIAGNOSTIC and ADJUST menu can be displayed as follows.
Press the button in order of “COUNTER-RESET button” → “STOP button” → “MODE CHK button” → “MENU
button”, DIAGNOSTIC and the ADJUST menu can be displayed in addition to a setup menus.
Next, press the PLAY or STOP button to select the DIAGNOSTIC or ADJUST menu. And press SET(STILL) button
to open the DIAGNOSTIC or ADJUST menu.
NOTE 1: P2-PC and TAPE-DUB mode can not be display the DIAGNOSTIC and ADJUST menu.
NOTE 2: Before performing menu operations on P2-MCR mode, you must clear the thumbnail screen. If the
thumbnail menu is displayed, press the THUMBNAIL button to release the display.
Normal Screen
(MCR or VCR mode)
CAMERA MENU
1. SCENE FILE
2. CAMERA SETUP
3. SW MODE
4. AUTO SW
5. RECORDING SETUP
6. AV IN/OUT SETUP
7. DISPLAY SETUP
8. CARD FUNCTIONS
PUSH MENU TO EXIT
MCR or VCR MENU
1. RECORDING SETUP
2. PLAYBACK FUNCTIONS
3. AV IN/OUT SETUP
4. DISPLAY SETUP
5. OTHER FUNCTIONS
6. OPTION MENU
7. DIAGNOSTIC MENU
8. ADJUST MENU
PUSH MENU TO EXIT
Press the button in order of “COUNTER-RESET
button” → “STOP button” → “MODE CHK
button” → “MENU button”.
button” → “STOP button” → “MODE CHK
button” → “MENU button”.
Normal Screen
(CAMERA mode)
CAMERA MENU
9. OTHER FUNCTIONS
10. OPTION MENU
11. DIAGNOSTIC MENU
12. ADJUST MENU
PUSH MENU TO EXIT
P2
Press the “STOP” or “PLAY” button.
P2
CARD FUNCTIONS MENU is only display
in P2 mode.
in P2 mode.
MODE CHK button
COUNTER-RESET button
MENU button
PLAY button
STOP button
SET button
THUMBNAIL button
INF-18
Display the following items on the DIAGNOSTIC and ADJUST menu by setting of operation mode.
OPERATION MODE
P2 TAPE
MENU ITEM
CAM MCR CAM VCR
BER
DISPLAY
X X X !
SAMPLE
SPEED X X X !
SOFT VERSION
!
X
!
X
EEPROM VERSION
!
!
!
!
CYLINDER X
X
!
!
TAPE RUN
X
X
!
!
THREADING X
X
!
!
1394 DIAG
!
!
!
!
DIAGNOSTIC
1394 UID
!
!
!
!
ATF
GAIN
X X X !
LINEARITY
X X X !
AUDIO FILTER
!
!
!
!
Y LEVEL
!
!
!
!
C LEVEL
!
!
!
!
CMPNT Y LEVEL
!
!
!
!
CMPNT PB LEVEL
!
!
!
!
CMPNT PR LEVEL
!
!
!
!
DEFECT COMP
!
X
!
X
DEBUG DISP
!
!
!
!
DEBUG MODE
!
!
!
!
LCD OFFSET
!
!
!
!
EVF OFFSET
!
!
!
!
ADJUST
1394 GAP COUNT
!
!
X X
!
: Displayed
X: Not displayed
NOTE: Please do not change the setting of the items of “DEFFECT COMP”, “DEBUG DISP” and “DEBUG
NOTE: Please do not change the setting of the items of “DEFFECT COMP”, “DEBUG DISP” and “DEBUG
MODE”. These items are for factory use only.
Factory default setting is “OFF”.
Factory default setting is “OFF”.
Click on the first or last page to see other AG-HVX200P / AG-HVX200AN / AG-HVX200E / AG-HVX200MC / AG-HVX202EN service manuals if exist.