Panasonic PT-TX300U / PT-TX300E / PT-TX300EA / PT-TW240U / PT-TW240E / PT-TW240EA / PT-TW330U / PT-TW330E / PT-TW330EA Service Manual ▷ View online
PT-TX300 / PT-TW240 / PT-TW330 series
5-3
5. Click "Next".
6. Click "Next".
7. Click "Finish".
PT-TX300 / PT-TW240 / PT-TW330 series
5-4
5-1-3 Firmware Upgrade
Procedure
1.
Set-up
- Hold on "Power" button and plug in the
power cord.
- Until Power will light orange,Temp and Lamp
LED will light red ,Loosen “Power” button.
- Connect projector with RS232 cable to PC.
- Connect projector with RS232 cable to PC.
2. Execute the "DLP Composer
TM
Lite 11.1.1"
file.
3. Setting "11.1.1 FlashDeviceParameters".
- Select the file "11.1.1
- Select the file "11.1.1
FlashDeviceParameters".
- Put "FlashDeviceParameters" file into the
folder where you setup "DLP Composer Lite
11.1.1".
4. Click "Edit" and "Perferences".
PT-TX300 / PT-TW240 / PT-TW330 series
5-5
5. Click "Communications".
- Select “Serial Port”, then click “Configure”.
- Select the COM Port which you are using.
- Select “Serial Port”, then click “Configure”.
- Select the COM Port which you are using.
6. “Serial Port Configuration” picture will
appear on the screen.
- Make sure the settings are as below:
(1) In “Baud Rate” item, select “115200”.
(2) In “Data Bits” item, select “8”.
(3) In “Stop Bits” item, select “1”.
(4) In “Parity” item, select “None”.
(5) In “RTS” item, select “Enable”.
(6) In “CTS” item, select “Disable”.
(7) Key in “2000” into “Read” and “Write”
- Make sure the settings are as below:
(1) In “Baud Rate” item, select “115200”.
(2) In “Data Bits” item, select “8”.
(3) In “Stop Bits” item, select “1”.
(4) In “Parity” item, select “None”.
(5) In “RTS” item, select “Enable”.
(6) In “CTS” item, select “Disable”.
(7) Key in “2000” into “Read” and “Write”
items of “ Timeouts (in milliseconds)”.
- Click "OK".
- Click "OK".
7. Choose "Flash Loader".
- Click "Browse" to search the firmware file
- Click "Browse" to search the firmware file
(*.img).
- Click "Open".
PT-TX300 / PT-TW240 / PT-TW330 series
5-6
8. Selete the item skip Boot Loader Area
- Select “32KB”.
- Click "Reset Bus" to erase the flash
- Select “32KB”.
- Click "Reset Bus" to erase the flash
memory.
9. If the FW is ready, click "Start Download" to
execute the firmware upgrade.
- Click “Yes” to erase the flash memory.
10. When firmware upgrade process is finished,
“Download Complete” will appear.
“Download Complete” will appear.
11. Check SYS FW version.
- Re-plug in power cord and Power on
the projector. Get into the service mode
(Power--Left--Right--Menu) to check
the system firmware version.
- Re-plug in power cord and Power on
the projector. Get into the service mode
(Power--Left--Right--Menu) to check
the system firmware version.
MCU-M05 LAN-13G
PT-TX300-B04 <Jun 26.2013-18:32>
PT-TX300-B04 <Jun 26.2013-18:32>
Lamp Hour-Full
50
Lamp Hou-Eco
30
Operating Hour
80
Lamp On/Off Counter
11/10
Lamp Voltage/ Max
33 / 43V
UART Response
0 No problems
Over Temp
0
FanLock
0
Lamp Fail
0
CW Fail
0
Spoke Test
✔
Burn in Test
✔
Color Wheel Index
✔
ADC Calibration
✔
SNID
WM2469999
Thermal Detect
Disable
Enable
Waveform ID
0/6/7/8/9/10
Debug Message PJC
On
Off
Direct Power On
On
Off
Factory Fan RPM
4807
Factory Reset
✔
Internal Bus Log
✔
Exit
✔
Click on the first or last page to see other PT-TX300U / PT-TX300E / PT-TX300EA / PT-TW240U / PT-TW240E / PT-TW240EA / PT-TW330U / PT-TW330E / PT-TW330EA service manuals if exist.