Panasonic PT-RZ970 / PT-RW930 / PT-RX110 (serv.man4) Service Manual ▷ View online
INF-5
SECTION 1 SERVICE INFORMATION
< RZ970/RW930/RX110 >
1. 4 Remote controls
1
3
2
4
5
5
7
6
8
9
10
15
12
11
13
14
16
17
Front
Top
Bottom
1 Power standby <v> button
Sets the projector to the state where the projector is turned
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in projection mode.
2 Power on <b> button
Sets the projector to projection mode when the <MAIN
POWER> switch on the projector is set to <ON> and the power
is turned off (standby mode).
3 Remote control indicator
Blinks if any button in the remote control is pressed.
4 Lens buttons (<FOCUS>, <ZOOM>, <SHIFT>)
Adjusts the projection lens.
5 <MENU> button/<ENTER> button/asqw buttons
Used to navigate through the menu screen.
asqw
asqw
buttons are also used to enter the password in
[SECURITY] or enter characters.
6 <ON SCREEN> button
Switches the on-screen display function on (display) or
off (hide).
7 Input selection buttons (<RGB1/2>, <DIGITAL LINK>,
<DVI‑D>, <VIDEO>, <SDI>, <HDMI>)
Switches the input signal to project.
(SDI input is supported only for PT-RZ970.)
8 <FUNCTION> button
Assigns a frequently used operation as a shortcut button.
9 Number (<0> - <9>) buttons
Used for entering an ID number or a password in a multiple
projector environment.
10 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed while in automatic adjustment.
11 <SHUTTER> button
Used to temporarily turn off the image.
12 <TEST PATTERN> button
12 <TEST PATTERN> button
Displays the test pattern.
13 <STATUS> button
Displays the projector information.
14 <DEFAULT> button
Resets the content of the sub-menu to the factory default.
15 <ID SET> button
Sets the ID number of the remote control in a multiple
projector environment.
16 Remote control signal transmitter
17 Remote control wired terminal
17 Remote control wired terminal
This is a terminal used to connect to the projector via a cable
when the remote control is used as a wired remote control.
Note
f
When operating the remote control by directly pointing at the remote control signal receiver of the projector, operate the remote control
within a distance approximately 30 m (98'5") from the remote control signal receiver. The remote control can control at angles of up to ±30°
vertically and horizontally, but the effective control range may be reduced.
f
If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
f
The signal will be reflected off the screen. However, the operating range may be limited from light reflection loss due to the screen material.
f
If the remote control signal receiver directly receives strong light, such as fluorescent light, the remote control may not operate properly. Use
it in a place distant from the light source.
f
The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
INF-6
SECTION 1 SERVICE INFORMATION
< RZ970/RW930/RX110 >
2. Menu Navigation
Main menu
The following items are in the main menu.
When a main menu item is selected, the screen changes to a sub-menu selection screen.
When a main menu item is selected, the screen changes to a sub-menu selection screen.
Main menu item
[PICTURE]
[POSITION]
[ADVANCED MENU]
[DISPLAY LANGUAGE]
[DISPLAY OPTION]
[PROJECTOR SETUP]
[P IN P]
[TEST PATTERN]
[SIGNAL LIST]
[SECURITY]
[NETWORK]
Sub-menu
The sub-menu of the selected main menu item is displayed, and you can set and adjust items in the sub-menu.
[PICTURE]
Sub-menu item
Factory default
[PICTURE MODE]
[GRAPHIC]
*1
[CONTRAST]
[0]
[BRIGHTNESS]
[0]
[COLOR]
[0]
*2
[TINT]
[0]
[COLOR TEMPERATURE]
[DEFAULT]
*2
[WHITE GAIN]
[+10]
[GAMMA]
[DEFAULT]
[SYSTEM DAYLIGHT VIEW]
[OFF]
*2
[SHARPNESS]
[+6]
*2
[NOISE REDUCTION]
[OFF]
*2
[DYNAMIC CONTRAST]
[2]
*2
[SYSTEM SELECTOR]
[YP
B
P
R
]
*1
*1 Depends on the signal input.
*2 Depends on the [PICTURE MODE]
*2 Depends on the [PICTURE MODE]
INF-7
SECTION 1 SERVICE INFORMATION
< RZ970/RW930/RX110 >
[POSITION]
Sub-menu item
Factory default
[SHIFT]
―
[ASPECT]
[DEFAULT]
*1
[ZOOM]
―
[CLOCK PHASE]
[0]
*1
[GEOMETRY]
[OFF]
*1 Depends on the signal input.
[ADVANCED MENU]
Sub-menu item
Factory default
[DIGITAL CINEMA REALITY]
[AUTO]
*1
[BLANKING]
―
[INPUT RESOLUTION]
―
[CLAMP POSITION]
[24]
*1
[EDGE BLENDING]
[OFF]
[FRAME RESPONSE]
[NORMAL]
[RASTER POSITION]
―
*1 Depends on the signal input.
Note
f
The factory default setting varies depending on the selected input terminal.
[DISPLAY LANGUAGE]
f
Various menus, settings, adjustment screens, control button names, etc., are displayed in the selected language.
f
The language can be changed to English, German, French, Spanish, Italian, Portuguese, Japanese, Chinese,
Russian, or Korean.
INF-8
SECTION 1 SERVICE INFORMATION
< RZ970/RW930/RX110 >
[DISPLAY OPTION]
Sub-menu item
Factory default
[COLOR MATCHING]
[OFF]
[COLOR CORRECTION]
[OFF]
[SCREEN SETTING]
―
[AUTO SIGNAL]
[OFF]
[AUTO SETUP]
―
[BACKUP INPUT SETTING]
―
[RGB IN]
―
[DVI-D IN]
―
[HDMI IN]
―
[DIGITAL LINK IN]
―
[SDI IN]
*1
―
[ON-SCREEN DISPLAY]
―
[CLOSED CAPTION SETTING]
―
[IMAGE ROTATION]
[OFF]
[BACK COLOR]
[BLUE]
[STARTUP LOGO]
[DEFAULT LOGO]
[UNIFORMITY]
―
[SHUTTER SETTING]
―
[FREEZE]
―
[WAVEFORM MONITOR]
[OFF]
[CUT OFF]
―
*1 Only for PT-RZ970
[PROJECTOR SETUP]
Sub-menu item
Factory default
[PROJECTOR ID]
[ALL]
[PROJECTION METHOD]
―
[OPERATION SETTING]
―
[LIGHT OUTPUT]
[100.0%]
[BRIGHTNESS CONTROL]
―
[STANDBY MODE]
[NORMAL]
[QUICK STARTUP]
[OFF]
[NO SIGNAL SHUT-OFF]
[DISABLE]
[NO SIGNAL LIGHTS-OUT]
[DISABLE]
[INITIAL STARTUP]
[LAST MEMORY]
[STARTUP INPUT SELECT]
[LAST USED]
[DATE AND TIME]
―
[SCHEDULE]
[OFF]
[MULTI PROJECTOR SYNC]
―
[RS-232C]
―
[REMOTE2 MODE]
[DEFAULT]
[FUNCTION BUTTON]
―
[LENS CALIBRATION]
[NORMAL]
[STATUS]
―
[SAVE ALL USER DATA]
―
[LOAD ALL USER DATA]
―
[INITIALIZE]
―
[SERVICE PASSWORD]
―
Click on the first or last page to see other PT-RZ970 / PT-RW930 / PT-RX110 (serv.man4) service manuals if exist.