Panasonic PT-RZ770 / PT-RW730 / PT-RZ660 / PT-RW620 (serv.man4) Service Manual ▷ View online
ADJ-12
SECTION 3 ADJUSTMENTS
< RZ770/RW730/RZ660/RW620 >
LD1-2
LD2-2
LD2-3
LD1-3
LD2-1
LD1-1
[Reference] t All LD units location
6. Click the [Reset] button corresponding to the replaced LD unit No.
7. A confirmation window is displayed. If LD No. is correct, click the [OK] button and reset the runtime.
(Display example of LD2-3 reset)
(Display example of LD2-3 reset)
8. Completion screen is displayed, and click the [OK] button. Confirm the runtime is set to 0h.
9. After completing the reset, restart the projector and check the runtime with the [STATUS] screen.
ADJ-13
SECTION 3 ADJUSTMENTS
< RZ770/RW730/RZ660/RW620 >
1. 8. LD unit status reset
f
If the LD unit is unconnected, the fault (open) status is retained when the power is on.
In this case, to clear the fault status by using the LDResetTool. (Runtime is not reset.)
1. Display the status of each LD unit at the same procedure to "1.7 LD unit runtime reset".
[Display example] t If the open failure of LD2-3.
2. A confirmation window will be displayed when click the [LD Status Reset] button.
Then Click the [OK] button.
3. Completion screen is displayed, and click the [OK] button. Confirm the status is set to "ON / ON".
4. After completing the reset, restart the projector and check the LD status with the [SELF CHECK] screen on service
mode.
ADJ-14
SECTION 3 ADJUSTMENTS
< RZ770/RW730/RZ660/RW620 >
2. Firmware Update Procedure
f
Firmware updating can be done via the LAN terminal or the serial terminal. (Updating of DIGITAL LINK firmware can be
done via the serial terminal only.)
f
The update procedure via the LAN terminal connection is recommended for quick updating.
2. 1. Equipment to be used
1. Computer : Use it for the transfer of firmware.
2. Communication cable :
3. Service software : [MainSubNet Update Tool.exe] Download from the projector service Web (PASS).
4. Firmware : Download the firmware file from the projector service Web (PASS) to the PC.
2. 2. Connection Preparations
1. Check the settings of the projector.
1) The [INPUT SELECT] of sub menu [RS-232C] must be set according to the connection method.
2) The [EMULATE] of sub menu [RS-232C], please set to [DEFAULT]. (in service mode)
3) Check the RS-232C settings (ID, Baudrate and Parity) and take a note.
1) The [DIGITAL LINK MODE] of sub menu [NETWORK], is select to [AUTO] or [ETHERNET].
2) Check the network IP address of the projector and take a note.
3) Set the IP address of computer to approximate value of projector IP address.
[Note]
• If you have changed the each menu settings, please return settings of the original (customers) after work.
• Set up your computer not to standby or shutdown.
2. Connect the projector and the PC by using a communication cable.
2. 3. Update procedure
1. Switch the projector to "Normal-Standby" mode (Power indicator is lighting in red).
2. Activate a [MainSubNet Update Tool.exe] Service software and select the Model No., then click the [OK] button.
Serial terminal connection
D-sub 9 pin (male/female RS-232C straight)
LAN terminal connection
LAN cable (When connecting directly, use a cross cable)
Serial terminal connection
LAN terminal connection
Serial terminal connection example
LAN terminal connection example
Projector
SERIAL IN
Communication cable (straight)
Computer
D-Sub 9P
(male)
LAN cable (straight)
LAN cable (straight)
Hub
Projector
LAN
Computer
ADJ-15
SECTION 3 ADJUSTMENTS
< RZ770/RW730/RZ660/RW620 >
• Select [SERIAL] menu and set up the Serial Port, Baudrate and Parity of the PC.
LAN terminal connection
• Select [LAN] menu and set up the IP address, Username, Password and Command Port of the projector.
[Note] • If the Username and Password has been changed, please select serial terminal connection.
4. After completing the connection setup, click the [Connection Check] button.
Items
Default
SERIAL
Port
–
Baud Rate
9600bps
Parity
None
LAN
IP Address
192.168.0.8
Username
admin1
Password
panasonic
Command Port
1024
3. Select the connection method, and enter the setting information of the projector.
Serial terminal connection
• When "Check : OK" is displayed, click the [OK] button and proceed to the next step.
• If "Check : NG" is displayed, check the setting in step 3.
Click on the first or last page to see other PT-RZ770 / PT-RW730 / PT-RZ660 / PT-RW620 (serv.man4) service manuals if exist.